RYOBI RPD500 500W Corded Impact Drill Instruction Manual

RYOBI RPD500 500W Corded Impact Drill

Product Information

• Product Name: RPD500
• Language Options: English, French, German, Spanish, Italian, Dutch, Portuguese, Danish, Finnish, Norwegian, Russian, Polish, Czech, Hungarian, Romanian, Latvian, Lithuanian, Estonian, Croatian, Slovenian, Slovakian, Greek, Turkish
• Special Safety Rules:
  • Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
  • Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
  • Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock.
  • Wear safety goggles to protect your eyes from flying particles and splinters.
• Intended Use:
  • Drilling and screw driving in all types of wood.
  • Drilling in metals: steel, brass, aluminum sheets, stainless steel and pipe (do not use impact drilling on these materials).
  • Drilling in masonry: stone and masonry (use impact drilling), wall tiles (use ordinary drilling first, then impact drilling).
  • Do not use this product in any other way other than those stated for intended use.
• Maintenance:
  • The product should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product will prevent accidental starting that could cause serious injury.
  • When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.
• Lubrication:
  • All of the bearings in the product are lubricated with a sufficient amount of high-grade lubricant for the lifespan of the product under normal operating conditions. Therefore, no further lubrication is required.
• Environmental Protection:
  • Recycle raw materials instead of disposing of as waste. The machine, accessories, and packaging should be sorted for environmentally friendly recycling.

Product Usage Instructions

• Wear ear protectors when impact drilling to prevent hearing loss.
• If supplied with the tool, use auxiliary handle(s) to maintain control and prevent personal injury.
• When performing operations where the cutting accessory may contact hidden wiring or its own cord, hold the power tool by insulated gripping surfaces to avoid electric shock.
• Always wear safety goggles to protect your eyes from flying particles and splinters.
• For drilling and screw driving in wood, follow standard drilling procedures.
• When drilling in metals su as steel, brass, aluminum sheets, stainless steel, and pipe, do not use impact drilling.
• When drilling in masonry such as stone and masonry walls, use impact drilling. For drilling wall tiles, start with ordinary drilling first and then switch to impact drilling.
• Do not use the product in any other way than stated for the intended use.
• Disconnect the product from the power supply before assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use to prevent accidental starting and serious injury.
• When servicing, use only identical Ryobi replacement parts to avoid hazards or product damage.
• No additional lubrication is required as all bearings in the product are already lubricated with high-grade lubricant.
• Recycle the machine, accessories, and packaging as environmentally friendly recycling.

Important: It is essential that you read the instructions in this manual before operating this machine.

Subject to technical modifications

What In The Box

Installation Instructions

Using Instructions

SPECIAL SAFETY RULES

• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Wear safety goggles to protect your eyes from flying particles and splinters.

INTENDED USE

• Drilling and screw driving in all types of wood.
• Drilling in metals: steel, brass, aluminum sheets, stainless steel and pipe (do not use impact drilling on these materials).
• Drilling in masonry: stone and masonry (use impact drilling), wall tiles (use ordinary drilling first, then impact drilling).
• Do not use this product in any other way other than those stated for intended use.

MAINTENANCE

WARNING

• The product should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product will prevent accidental starting that could cause serious injury.
• When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.
• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
• Do not at any time let brake fl uids, gasoline, petroleum based products, penetrating oils, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
• Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc.
• Consequently, we do not recommend using this tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the product using compressed air.

WARNING

• Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
• If the power supply cord is damaged, it must be replaced only by the manufacturer or by an authorized service center to avoid risk. Contact authorized service center.

LUBRICATION

• All of the bearings in the product are lubricated with a sufficient amount of high grade lubricant for the life span of the product under normal operating conditions. Therefore, no further lubrication is required.

ENVIRONMENTAL PROTECTION

• Recycle raw materials instead of disposing of as waste.
• The machine, accessories and packaging should be sorted for environmental-friendly recycling.

SYMBOLS

• Safety Alert

• Class II, double insulated

• Wood

• Metal

• Masonry

• Impact

• Chuck

• CE conformity

• GOST-R conformity

• Please read the instructions carefully before starting the machine.

• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Product Specifications

• Voltage: 230V 50Hz
• Input: 500W
• No-load speed: 0 – 3,000 min-1
• Blows per minute (Impact rate): 0 – 50,000 min-1
• Chuck capacity: 13 mm
• Drilling capacity
  • in wood: 25 mm
  • in metal: 13 mm
  • in masonry: 13 mm
• Weight According to EPTAProcedure 01/2003: 1.6 kg

WARRANTY

All Ryobi products are guaranteed against manufacturing defects and defective parts for a period of twenty-four (24) months from the date stated on the original invoice drawn up by the retailer and given to the end user. Deterioration caused by normal wear and tear, unauthorised or improper use or maintenance, or overload are excluded from this guarantee as are accessories such as battery packs, light bulbs, blades, fittings, bags. In the event of a malfunction during the warranty period, please take the NONDISMANTLED product, along with the proof of purchase, to your retailer or nearest Authorised Ryobi Service Centre. This warranty in no way affects your legal rights concerning defective products.

AUTHORISED SERVICE CENTRE

• To find an authorised service centre near you, visit ryobitools.eu.

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

EC Declaration Of Conformity

Techtronic Industries GmbH

• Max-Eyth-Straße 10, D-71364 Winnenden, Germany

Herewith we declare that the product

• Percussion Drill
• RPD500
• S/N: 80000201000001 – 80000201999999

is in conformity with the following standards or standardized documents

• 2006/42/EC, 2004/108/EC, 2011/65/EU
• EN55014-1:2006+A1:2009+A2:2011, EN55014-2:1997+A2:2008, EN61000-3-2:2006+A1:2009+A2:2009, EN61000-3-3:2008, EN60745-1:2009+A11:2010, EN60745-2-1:2010.
• Sound pressure level [K=3dB(A)]: 95,0 dB (A)
• Sound power level [K=3dB(A)]: 106,0 dB (A)

Weighted root mean

The vibration total values(triax vector sum) determined according to EN60745:

• Impact drilling into concrete: ah=15,5 m/s2 K=1.5 m/s2

• Impact drilling into metal: ah= 3,6 m/s2 K=1.5 m/s2

• Vice President of Engineering

• Winnenden, Nov. 2, 2012

Authorised to compile the technical file:

• Rainer Kumpf
• Techtronic Industries GmbH
• Max-Eyth-Straße 10, D-71364 Winnenden, Germany

References

• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>