Harley Benton 119603 Powerplant Power Supply User Manual

Powerplant

User Manual

Power Supply

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
Internet: www.thomann.de

13.09.2022, ID: 119603 (V2)

1 General information

This user manual contains important information on the safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future reference. Make sure that it is available to all persons using this device. If you sell the device to another user, be sure that they also receive this manual.

Our products and user manuals are subject to a process of continuous development. We there- fore reserve the right to make changes without notice. Please refer to the latest version of the user manual which is ready for download under www.thomann.de.

1.1 Further information

On our website (www.thomann.de) you will find lots of further information and details on the following points:

topics of interest for you quickly.
Online guides| Our online guides provide detailed information on technical basics and terms.
Personal consultation| For personal consultation please contact our technical hotline.
Service| If you have any problems with the device the customer service will gladly assist you.

1.2 Notational conventions

This manual uses the following notational conventions:

Letterings

The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.

1.3 Symbols and signal words

In this section you will find an overview of the meaning of symbols and signal words that are used in this manual.

immediate dangerous situation that will result in death or serious injury if it is not avoided.
NOTICE!| This combination of symbol and signal word indicates a possible dangerous situation that can result in material and environmental damage if it is not avoided.
Warning signs| Type of danger
---|---
| Warning – high-voltage.
| Warning – danger zone.

2 Safety instructions

Intended use

This device transforms mains voltage into safety extra-low voltage, e.g. for the voltage supply of effects pedals. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.

This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Safety

DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices.

DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device if covers, protectors or optical components are missing or damaged.

DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a protective contact plug. Do not modify the mains cable or the plug. Failure to do so could result in electric shock/death or fire. If in doubt, seek advice from a registered electrician.

NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions specified in the chapter ‘Technical specifications’ of this user manual. Avoid heavy temperature fluctuations and do not switch the device on immediately after it was exposed to temperature fluctuations (for example after transport at low outside temperatures). Dust and dirt inside can damage the unit. When operated in harmful ambient conditions (dust, smoke, nicotine, fog, etc.), the unit should be maintained by qualified service personnel at regular intervals to prevent overheating and other malfunction.

NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker. Failure to do so could result in damage to the device and possibly injure the user. Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire.

NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react with the coating of your surface and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the surface and use a suitable underlay if necessary, i.e. felt pads or similar.

3 Installation and starting up

Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.

Wiring

Create all connections while the device is not connected to the mains. Use the supplied cables for all connections.

The following cable types are available:

8 standard cables (1:1), plug-plug, length 55 cm, each to supply one effects pedal with 9 V ⎓, black/white, centre negative.

2 standard cables (1:1), plug-plug, length 35 cm, each to supply one effects pedal with 12 V ⎓ or 12 V ~, 1 × red, 1 × blue, centre negative.

1 adapter cable with 3.5 mm phone plug (1:1), plug-socket, length 35 cm, to supply one effects pedal.

3 adapter cables plug-socket for changing the polarity (from centre negative to positive), length 20 cm.

4 Components and functions

Connection side

1

| Output sockets to supply effects pedals with a voltage of 9 V ⎓
---|---

2

| [POWER] | blue control LED. Indicates that the device is connected to the power supply. The LED turns off a few seconds after switching off the power supply of the device.

3

| Output socket to supply effects pedals with a voltage of 12 V ⎓

4

| Output socket to supply effects pedals with a voltage of 12 V ~

Left side view

5

| [POWER ON|OFF] | mains switch to turn the device on and off
---|---

6

| [MAINS VOLTAGE] | IEC chassis plug for power supply with fuse holder

5 Technical specifications

1 × 12 V ⎓, max. 500 mA
1 × 12 V ~, max. 500 mA
Dimensions (W × H × D)| 165 mm × 50 mm × 85 mm
Weight| 1 kg
Ambient conditions| Temperature range| 0 °C…40 °C
Relative humidity| 20 %…80 % (non-condensing)

Further information

6 Protecting the environment

Disposal of the packaging material

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.

Ensure that plastic bags, packaging, etc. are properly disposed of.

Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.

Disposal of your old device

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose with your normal household waste.

Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.

Notes

Powerplant
Power Supply

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>