Rebel RB-5010 Pressure Washer User Manual
- June 12, 2024
- Rebel
Table of Contents
Rebel RB-5010 Pressure Washer
Product Information
- Product Name : RB-5010 Pressure Washer
- Model : RB-5010
- Manufacturer: Lechpol Electronics Leszek Sp.k.
- Website : www.rebelelectro.com
Product Usage Instructions
- Read the entire instruction manual before installation and assembly. Keep the manual for future reference.
- Before connecting the device to a power supply socket, ensure that the voltage indicated on the device matches the voltage in the power supply socket.
- Place the device on stable and flat ground.
- Clean the device according to the instructions in the Cleaning and Maintenance section.
- Always turn off the device and disconnect it from the mains supply before performing any maintenance or adjustments.
Operation:
- Connect the extension wand with the gun. Insert the lance plug into the output hole of the gun and turn it clockwise until it locks into place.
- Connect a lance with an adjustable nozzle to the extension lance in the same way. To change the shape of the water jet, turn the nozzle.
- Connect a high-pressure hose to the gun. Insert the hose plug into the hole located at the bottom of the gun near the trigger. You will hear a clicking sound when properly installed.
- To release the hose, press the hose release button and pull out the hose.
SAFETY INSTRUCTIONS
In order to reduce the injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:
- Read the entire instruction manual before you start installation and assembly and keep it for future reference. Keep the manual for future reference.
- Before connecting the device to power supply socket, make sure the voltage indicated on the device corresponds to the voltage in the power supply socket.
- Place the device on stable, flat ground
- Clean this device in accordance to the instructions listed in the Cleaning and Maintenance section.
- ALWAYS turn off the device and disconnect it from the mains supply:
- if it’s not operating correctly
- if there’s an uncommon voice when using
- before disassembling the device
- before cleaning
- when not in use
- When you disconnect the power cord of the device, grasp and pull the plug, not the cord/cable.
- Fixed power cable may only be replaced in an authorized service point.
- Turn off the device by rotating power switch before disconnecting the power cord.
- Keep the device out of the reach of children. Only adult persons should use the pressure washer.
- Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
- Do not carry the pressure cleaner by the cord or hose.
- Do not pull the cord over sharp edges and do not slam in by the door.
- Make sure the plug does not bump into people, animals or objects when winding the cord.
- Do not step on the hose or crush it.
- Do not place the appliance in water or any liquid.
- Do not point hose or tube at people or animals.
- Do not use the device to clean animals or people.
- Do not use the product for purposes different from those displayed in this operating manual.
- Do not leave the appliance unattended when it’s working.
- The producer of this product is not responsible for damages caused by inappropriate handling and use of the device.
- DO NOT use this device if the cord or the plug is damaged, or the appliance is broken.
- Do not use the device if any accessory is damaged or leaky.
- Do not use the device at very low temperatures (below 0ºC)
- Do not attempt to repair this device yourself. Only authorized and qualified personnel may repair this device. Never disassemble this device.
- During work, use personal protection equipment. Always wear safety eye protection when using this pressure washer
- When working with delicate materials, do not bring the nozzle too close to the surface to be cleaned.
- After working with the device, roll up the power cord and place it on the hook.
OPERATION
- Connect extension wand with gun. To do this, insert the lance plug into the output hole of the gun and turn clockwise until the element locks into place.
- Connect a lance with an adjustable nozzle to the extension lance in the same way. To change the shape of the water jet, turn the nozzle.
- Connect a high-pressure hose to the gun. Insert the hose plug into the hole located at the bottom of the gun near the trigger. A clicking sound will be heard after proper installation. To release the hose, press the hose release button and pull out the hose.
- Connect the other end of the high pressure hose to the outlet port located on the front of the unit. A clicking sound will be heard after proper installation. To release the hose, slide the hose lock release switch and pull out the hose.
- Screw the input adapter to the water input hole on the back of the device, and then use the quick coupler to connect the water hose to it.
- Connect the power cord to the power supply socket.
- Switch power switch to “ON” position.
- To trigger the ejection of water from the gun, press the trigger located in its handle. At the bottom of the pistol’s handle is the pistol trigger lock switch. To lock the trigger, move the lock switch to the position marked with the padlock icon.
- Before each use of the washer, it should be bleeded, as there may be air in the system. To do this, after installing accessories, connect the hose with water and press the trigger of the gun. The entire operation should be carried out after making sure that the power switch is set to the OFF position.
CLEANING AND MAINTENANCE
- Before cleaning, rotate the power switch and unplug the device from the AC outlet.
- Then disconnect the water supply hose to the washer.
- Remove the input adapter and clean it.
- When the device is disconnected from the water source, high pressure will be maintained in the gun. Before removing the gun, point it at an empty space and squeeze the trigger. After disassembling the connected accessories, dry them.
- Store the device at temperatures above 0ºC.
DESCRIPTION
- Handle
- Hook for the power cord
- Power switch
- Power cord
- High-pressure hose
- Output hole for high-pressure nose wheel
- Gun mount
- Hion pressure nose release button
- Gun
TROUBLESHOOTING
| Problem | Cause | Solution |
|---|---|---|
| Motor does not run when the power switch is set to the ON position | Electrical | |
| socket does not work | Check plug, socket, fuses | |
| Socket voltage is inadequate | Check voltage in socket | |
| Power cord is not plugged in | Plug power cord | |
| The pump does not reach adequate pressure | Water inlet is clogged | Remove and |
clean adapter
Pump is drawing air| Check inlet connection / bleed system
Suction valves are clogged
/ worn
| Clean or replace valves
Diameter of garden hose is too small| Replace the hose with another with a
diameter of ¾ inch.
The water supplied to the washer has too low pressure| Check the water supply
hose for leaks / Open the water supply hose valve fully
Pressure cleaner makes excessive noise| Intake is blocked| Check the patency
of the intake valves
Valves are worn , dirty or clogged| Check intake valves
Filter is dirty| Check adapter filter
The motor stops running while in use| Net voltage is lower than suggested|
Check the voltage at the power socket
SPECIFICATION
| Power | 1200 W |
|---|---|
| Rated pressure | 70 bar (max 100 bar) |
| Rated flow | 330 l / h |
| Max. water supply pressure | 1,2 MPa |
| Max. water temperature | 50ºC |
| Power supply | 220 – 240 V AC , 50 / 60 Hz |
| Dimensions | 332 x 266 x 681 mm |
| Weight | 5,6 kg |
| In set | Gun, extension lance, lance with adjustable nozzle, hose, input |
adapter with filter
Sound pressure level (LPA)| 81 dB (A), K= 3 dB (A)
Sound power level (LWA)| 92 dB (A), K= 3 dB (A)
Hand-arm vibration| ah 2,5 m/s2 K=1,5 m/s2
LEARN MORE
For more information on this device visit:
www.rebelelectro.com.
Read the owner’s manual carefully before using your device.
Visit www.rebelelectro.com website for more
products and accessories.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400
Miętne.
CE DECLARATION OF CONFORMITY
Supplier’s name : Lechpol Electronics Leszek Sp.k.
Supplier’s address : ul. Garwolińska 1, 08-400 Miętne, Poland
Equipment type Pressure washer
Model : RB-5010 (LT303 – 1200D)
We, the undersigned, hereby declare that the equipment specified above
confirms to the following directives:
Product standard:
- EN 60335-1:2012/A2:2019
- EN60335-2-79:2012
- EN 62233:2008
According to the following European directive:
Machinery Directive: 2006/42/EC
EMC Directive : 2014/30/UE
RoHS Directive : 2011/65/UE (EN IEC 63000:2018)
WEEE Directive : 2012/19/EC
Supplier : Lechpol Electronics Leszek Sp.k.
Representative’s name: Marek Puszkiel
Place and date of issue : Garwolin, Poland; 07.02.2023
www.rebelelectro.com
Multilanguage manual available at :
www.rebelelectro.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>