GAS MAD X2-34 Car Audio Specialist Owner’s Manual
- June 12, 2024
- GAS
Table of Contents
GAS MAD X2-34 Car Audio Specialist
SAFETY
PLAY LOUD & SAFE. Read through this information, follow the instructions and
save the manual for future usage and reference.
Make sure to pay attention to the instructions when you see this symbol:
Do not expose the wiring to your new speaker to excessive damp or moisture. If
the speaker’s wiring is exposed it might result in electric failure, shock or
damage to the product. Servicing is required when the product has been damaged
in any way and/or doesn’t operate normally. Refer all servicing to qualified
service personnel only. Keep the cables inside the vehicle separate from sharp
edges or components that may be affected or take damage. Follow the
recommended cable sizes and always use high quality cables and accessories.
Even if you’re eager to put the speakers to use -take no shortcuts when
installing the cables, make sure that all connectors are protected and
secured. Do not drill any holes without checking what lies beneath, and don’t
cut anything without making sure that no important components risk being
damaged. There is a first time for everything, if you need help – ask a friend
or contact your local GAS AUDIO POWER dealer/installer. We want you to
experience your product’s MAD sound, but we don’t want you to injure yourself
or others. Use common sense, respect high pressure levels and volume, and
follow your local laws and regulations.
UNPACKING
Unboxing your new MAD product is an experience, make sure that the speakers and all the accessories are included in the packaging:
DIMENSIONS
SPECIFICATIONS
Below you’ll find the specifications that has been checked and tested in our workshop. The specified sensitivity isn’t directly connected with the sound pressure in the vehicle, and shouldn’t be used as the sole indicator for comparison with other speakers.
FEATURES
The MAD coaxial speakers are made to be LOUD and last for years to come. We want to help you and your vehicle to be as LOUD as possible. We’ve made sure that’s the case by using innovative and groundbreaking techniques that increase durability.
A MAD SPEAKER TO FIT EVERY NEED
There’s nothing better than replacing that old dusty wannabe speaker that’s
been hiding behind your speaker grills. Did your old speakers break ’cause
they couldn’t handle your level of LOUD? The X2 series is ready for you. Be
proud, be loud, be MAO!
YOUR CAR WAS MADE FOR THE X2 SERIES
Just the way you like it, just the way your car wants it – uncomplicated and
made to fit like a glove. The speaker has a 13mm silk dome tweeter with NED
magnet structure and a newly developed tweeter faceplate to up your LOUD game!
In boring science terms, this means you get an increased dispersion and off-
axis reproduction. It also makes the speaker a perfect fit for non-ideal OEM
speaker placement. The column that holds the tweeter also contains an inline
crossover. This invisible placement makes the look of the speaker extra sleek.
DESIGNED TO BE DURABLE
Our research department has truly gone MAD! For our MAD S2 subwoofers we
developed a new kind of IMPP cone. We decided that this feature was so good –
we brought it over to the X2 series. This means that the X2 series speakers
are very durable, moist proof and ready to kick some ass!
SWEDISH DESIGN, MAD SENSIBILITIES
The 25mm KSV voice coil is wound with lightweight CCAW (Copper Clad Aluminum
Wire) that creates a dynamic sound. Since the Swedish weather encompasses all
different seasons – the X2 series is designed to withstand them all. Hot,
cold, UV rays – it doesn’t matter. It’s MAD and it’s made to play LOUD, no
matter the circumstances!
HOWTO
INSTALL SPEAKERS
Before installing your brand new speakers, make sure that you have everything
you need. Have the right tools ready and make sure you have the necessary
skills/knowledge to perform the installation properly. Preparation and
knowledge is crucial! The MAD X2 series uses a single 4 Ohm voice coil. If you
want to connect four or more X2 series speakers, you can vary the impedance by
altering the wiring configuration to use a series or parallel setup. The more
the merrier! Make sure to look through the recommended wiring schematics below
and choose the setup that corresponds with the number of speakers in your
sound system. Take note of the impedance stability of your amplifier. Don’t be
afraid to consult your local GAS AUDIO POWER dealer/installer if you have any
questions.
SPEAKER PLACEMENT
Wiring tutorial – check! Now you know how to connect your cables and speakers
correctly, but where do you place the speakers? You will most likely have one
or two possible locations to put the speakers depending on make and model.
This is where the fun begins!
-
FRONT DOORS
The front right and left doors are typical speaker positions. In some models you’ll find original speakers in the kickpanel – right in front of the doors in the footwell. -
BACK DOORS
If your car’s on the newer side of the spectrum, you might find OEM coaxial speakers here and component speakers in the front. Friends in the back seat need awesome sound too! -
REAR SHELF
If you don’t have speakers here, you’re missing out! The rear shelf is a popular location by sound enthusiasts and some car manufacturers. If you don’t have it -AO□ it! -
DASH
This speaker placement is found in some car models, and is normally really great for a smaller midrange, coaxial and/or tweeter speaker.
TROUBLESHOOTING
NO POWER/SOUND
Check the speakers to make sure they’re not damaged. If your speakers don’t
get any power, the most common issue is either in the wiring or in the
amplifier. Use a multimeter to measure the amplifier’s voltage on the +12V
terminal and the remote signal terminal. Use a multimeter to make sure that
you have a negative ground connection. Check the built-in fuse (if there’s
one) on the amplifier. If there’s no power coming through – control the fuse
on the power cable. If it’s intact – make a full check of the wiring to ensure
cable integrity. Check all the speakers connected to your sound system. Check
all the speaker cables and all the signal cables. Check your head unit to make
sure no settings are limiting the amplifier’s functions or the speakers. When
all of the above has been tested/looked over, and all is as it should be but
there’s still no sound, consult your local GAS AUDIO POWER dealer/installer.
UNWANTED NOISE
Start by looking over the speakers in the sound system so there is no damage
or connection issue with the wiring. Make sure that your signal cables or
speaker cables aren’t too close to the power cables. Check your amplifier’s
grounding point and make sure that the surface is clean. When all of the above
has been tested/looked over, and the unwanted noise does not vanish, consult
your local GAS AUDIO POWER dealer/installer.
DISTORTION
Start by looking over the speakers in the sound system so there’s no damage or
connection issue with the wiring. Check the speaker cables to make sure that
the polarity isn’t reversed on one channel. Check the settings on the
amplifier, make sure that the gain/level is set according to the amplifier’s
instructions. If your amplifier has a boost function, lower its effect or turn
it off.
WARRANTY & DISPOSAL
This product is covered by warranty, depending on the conditions in the country where it’s sold. If the speakers are returned for service, please include the original dated receipt (or a copy) with the product. Make sure that the speakers are packaged properly and secured, preferably in its original packaging.
The crossed-out wheelie bin symbol means that the product, literature and
packaging included must be taken to separate collection at the end of their
working life. Don’t dispose of these products as unsorted municipal waste:
take them for recycling. For info on your nearest recycling point, check with
your local waste authority.
This product has been granted with the CE certification mark to show that the
product follows the health, safety, and environmental protection standards for
products sold within the European Economic Area (EEA).
GAS Audio Power products comply with the relevant proVisions of the RoHS
Directive for the European Union. In common with all Electrical and Electronic
Equipment (EEE) the product shouldn’t be disposed of as household waste.
Alternative arrangements may apply in other jurisdictions.
GAS Audio Power is a global partner of the European Mobile Media Association,
an organization that focus on promoting the custom-made mobile media
installations to consumers.
THE GAS WORLD
You’ve entered the world of GAS. We aim to please, and we’ve made sure to have products made for you. No matter what stage of the LOUDaddiction you might find yourself in, there is a GAS product to fill your need.
Just starting out? The MAD series is made to play LOUD and to be the
express lane to a no bullshit sound system that will make sure everyone can
hear you coming!
The MAX series holds products made to deserve the center stage. Powerful,
heavy duty and designed to be noticed. We made NO COMPROMISES because we know
that you wouldn’t accept it.
The CMP series has been developed for the crucial seconds when the dB-
counter starts to tick. All CMP products have hand-picked, high quality,
COMPETITION GRADE components and they are specially designed to withstand an
awesome amount of power.
AUDIO POWER
GAS AUDIO POWER and SHAKY are registered trademarks by Winn Scandinavia AB and
is protected by relevant laws and jurisdictions such as Copyright and
Trademark laws. Winn Scandinavia AB I Elementvagen 15, 70227 Orebro, Sweden I
www.winnscandinavia.com Winn Scandinavia AB
reserves for possible typos, factual or numeric errors that may have been
printed on any products, package designs, user manuals and/or other included
accessories.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>