Einhell CC-HS 12-2 Car Hammer Screwdriver Instruction Manual

: June 12, 2024
: Einhell

Einhell CC-HS 12-2 Car Hammer Screwdriver

Product Information

The product is a car hammer screwdriver, designed for automotive use. It has a model number of CC-HS 12/2 and is manufactured by Einhell. The product comes with original operating instructions in multiple languages, including German, English, Slovenian, French, Italian, Swedish, Dutch, Greek, Croatian, Bosnian, Serbian, Polish.

The product is equipped with various features and specifications:

Model Number: CC-HS 12/2
Art.-Nr.: 20.483.13
I.-Nr.: 21012
Sound pressure level (LpA): 86 dB(A)
Uncertainty (KpA): 3 dB
Sound power level (LWA): 97 dB(A)
Uncertainty (KWA): 3 dB
Vibration emission value (ah): 4.27 m/s2
Uncertainty (K): 1.5 m/s2

Product Usage Instructions

Before using the car hammer screwdriver, please read and follow the safety instructions provided in the user manual. Ensure that all packaging and transport safety measures are removed before use.

Safety Instructions

Always use appropriate safety gear such as ear-muffs and safety
goggles to protect against noise and potential eye injuries.
Check for any existing fuses or safety measures and remove them if necessary.
Do not exceed the specified warranty period.

Technical Specifications

Sound pressure level (LpA): 86 dB(A)
Uncertainty (KpA): 3 dB
Sound power level (LWA): 97 dB(A)
Uncertainty (KWA): 3 dB
Vibration emission value (ah): 4.27 m/s2
Uncertainty (K): 1.5 m/s2

Before Operation

Prior to using the car hammer screwdriver, please take note of the following:

Clean the device after each use.
Use the water level bubble (Libelle) to ensure proper alignment of the screwdriver attachment on a wheel nut/bolt.

Cleaning, Maintenance, and Spare Part Ordering
To clean the car hammer screwdriver, make sure to unplug the 12V plug. For maintenance and spare part ordering, please refer to the provided instructions and visit Einhell’s official website for current prices and information.
Disposal and Recycling
Follow proper disposal and recycling guidelines for the car hammer screwdriver.

Service Information

If you require service or have any product-related inquiries, you can contact Einhell’s service department via phone, fax, or email.

Phone: 09951 – 959 2000
Fax: 09951 – 959 1700
Email: Service-DE@Einhell.com. You can also visit Einhell’s website for more information and services.
Website: www.Einhell-Service.com.

Danger!
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Explanation of the symbols used (see Fig. 2)

Danger! – Read the operating instructions to reduce the risk of injury.
Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.
Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.

Safety regulations

The corresponding safety information can be found in the enclosed booklet.
Warning! Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fi re and/or serious injury. Keep all the safety information and instructions in a safe place for future use. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Layout and items supplied

Layout (Fig. 1) $Einhell-CC-HS 12-2 Car-Hammer-Screwdriver-FIG-1 $1$$

External square drive mount
Spirit level
Selector switch for clockwise/counter-clockwise rotation
On/Off switch
LED lamp
Power cable
12 V power plug with integrated fuse

Items supplied

Please check that the article is complete as specifi ed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

Open the packaging and take out the equipment with care.
Remove the packaging material and any packaging and/or transportation braces (if available).
Check to see if all items are supplied.
Inspect the equipment and accessories for transport damage.
If possible, please keep the packaging until the end of the guarantee period

Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suff ocating!

1 impact driver 12 V DC
1 set each of double-ended socket inserts size 17/19 mm and 21/23 mm
2 spare miniature fuses (30 x 6 mm / 15 A)
Original operating instructions
Safety instructions

Proper use

The impact driver is a handy DC tool designed to be connected to a motor vehicle‘s 12 V power supply for use in the automotive fi eld. It is suitable for fastening and releasing threaded connections on motor vehicles (fi tting tyres, etc.). The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Technical data

Max. loosening torque …………………………350 Nm
Operating voltage …………………………….. 12 V DC
Power rating ……………………………………….. 80 W
Working range (max. thread size) ……………. M14
Square drive mount …………….12.7 mm (1/2 inch)
Weight ……………………………………………….1.7 kg

Danger! Sound and vibration
Sound and vibration values were measured in accordance with EN 60745.

LpA sound pressure level …………………… 86 dB(A)
KpA uncertainty ………………………………………3 dB
LWA sound power level …………………….. 97 dB(A)
KWA uncertainty ………………………………………3 dB

Wear ear-muff s.
The impact of noise can cause damage to hearing. Total vibration values (vector sum of three directions) determined in accordance with EN 60745. Vibration emission value ah = 4.27 m/s2 K uncertainty = 1.5 m/s2 The stated vibration emission levels and stated noise emission values were measured in accordance with a set of standardized criteria and can be used to compare one power tool with another. The stated vibration emission levels and stated noise emission values can also be used to make an initial assessment of exposure.
Warning: The vibration and noise emission levels may vary from the level specifi ed during actual use, depending on the way in which the power tool is used, especially the type of workpiece it is used for.

Keep the noise emissions and vibrations to a minimum.

Only use appliances which are in perfect working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.

Caution! Residual risks Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout:

Lung damage if no suitable protective dust mask is used.
Damage to hearing if no suitable ear protection is used.
Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Limit the operating time!
All stages of the operating cycle must be considered (for example, times in which the electric tools are switched off and times in which the tool is switched on but operates without load).

Before starting the equipment

Use only drive socket inserts which are suitable for the purpose and in faultless condition.
Note: This tool is equipped with a centrifugal clutch.

A) When the drive socket insert fi tted to the square drive mount is placed on the wheel nut/wheel bolt, this will result in the motor being loaded. The motor will run without the drive socket insert turning. Using the centrifugal clutch, the motor builds up torque and performs short impact movements on the drive socket insert when this torque is reached. As the result, the wheel nut/wheel bolt will be tightened or slackened.
B) When the motor is not loaded, the square drive mount or the fi tted drive socket insert will rotate. Caution! Never hold the square drive mount or the fi tted drive socket insert with your hand. You could be injured by a sudden impact movement.

Operation

Power supply
Connect the 12 V power plug (Fig. 1 Item 7) to the vehicle’s cigarette lighter socket.
The direction of rotation switch (Fig. 1/Item 3)
The slide switch above the On/Off switch is for setting the direction of rotation of the impact driver and for preventing the impact driver from being switched on inadvertently. You can select between counter-clockwise and clockwise rotation. To avoid causing damage to the gearing, the direction of rotation is allowed to be changed only when the equipment is at a standstill. When theslide switch is in the middle position, the On/Off switch is blocked.
On/Off switch (Fig. 1/Item 4)
Switching on:
Press the On/Off switch (4).
Switching off :
Release the On/Off switch (4)
Working with the impact driver
Plug the required drive socket insert on thesquare drive mount. Select the correct direction of rotation on the impact driver.

Note:

The spirit level on the top of the driver (Fig. 1 / Item 2) helps you to fit the drive socket insert onto a wheel nut/wheel bolt in a straight position.
The LED light (Fig. 1 / Item 5) will come on when the equipment is connected to the 12 V power supply. It enables the work area to be illuminated when lighting conditions are poor.

Tightening
Push the drive socket insert onto the screw head and actuate the On/Off switch. Carefully insert the bolt or nut in the thread before you move the electric driver into position. A torque of approx. 50 Nm per pulse is generated on standard bolts of size M12/M14. On motor cars, each bolt should be tightened with two pulses. Each bolt should then be checked with one additional pulse. A total torque of approx. 150 Nm is thus achieved. Three pulses are recommended on heavy vehicles (e.g. luxury cars, off -road vehicles, etc.). Each bolt should then be tightened in diametrically opposed order with one additional pulse. A total torque of approx. 200 Nm is thus achieved. Check the threaded connections for signs of damage after tightening.
Danger! Always check and retighten wheel nuts with a torque wrench that is set to the torque specific ed by the manufacturer of the vehicle in question.
Slackening
To slacken a wheel bolt/wheel nut proceed as described in the section “Tightening” but use the opposite direction of rotation. Several impact pulses will be needed depending on how tight the wheel nut/wheel bolt is seated.

Cleaning, maintenance and ordering of spare parts

Danger! Pull out the 12 V plug.

Cleaning

Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
We recommend that you clean the device immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

Maintenance

There are no parts inside the equipment which require additional maintenance.
Replacing the fuse in the 12 V plug
If an overload occurs, the 15 A fuse in the 12 V power plug will melt. Unscrew and remove the top end of the plug and replace the defective fuse with one of the same type. Screw the top end of the plug back in place. Find out what caused the overloading.
Ordering replacement parts:
Please quote the following data when ordering replacement parts:

Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required For our latest prices and information please go to www.Einhell-Service.com.

Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.
Storage
Store the equipment and accessories in a dark and dry place at an above- freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging. For EU countries only Never place any electric power tools in your household refuse. To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot. Recycling alternative to the return request: As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aid without electrical components supplied with the old equipment. Please note that batteries and lamps (e.g. light bulbs) must be removed from the tool before it is disposed of. The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of Einhell Germany AG. Subject to technical changes

Service Information

We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requestssuch as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Category	Example
Wear parts*	Drive socket inserts
Consumables*	Miniature fuse
Missing parts

Not necessarily included in the scope of delivery!
In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

Did the equipment work at all or was it defective from the beginning?
Did you notice anything (symptom or defect) prior to the failure?
What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.

Warranty certifi cate

Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.
The warranty services cover only defects due to material or manufacturing faults on a product that you have bought from the manufacturer mentioned below and are limited to either the rectifi cation of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade, or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out orparts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if an on-site service is used.
To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identification will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.

Of course, we are also happy off er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address. Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.

Declaration of conformity

We declare conformity in accordance with the EU directive and standards for article

*Kfz-Schlagschrauber CC-HS 12/2 (Einhell)**

2014/29/EU
2005/32/EC_2009/125/EC
(EU)2015/1188
2014/35/EU
2006/28/EC
X 2014/30/EU
2014/32/EU
2014/53/EU
2014/68/EU
(EU)2016/426
Notifi ed Body:
(EU)2016/425
X 2011/65/EU_(EU)2015/863
X 2006/42/EC
Annex IV
Notifi ed Body:
Reg. No.: 2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured LWA = dB (A); guaranteed LWA = dB (A) P = kW; L/Ø = cm
Notifi ed Body: 2012/46/EU_(EU)2016/1628
Emission No.:

Standard references: EN 62841-1; EN 62841-2-2; EN 55014-1; EN 55014-2

Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar Landau/Isar, den 15.04.2022

First CE: 22
Art.-No.: 20.483.13 I.-
No.: 21012 Subject to change without notice
Archive-File/Record: NAPR027594
Documents registrar: Landauer Josef Wiesenweg 22, D-94405 Landau/Isar

Car Hammer Screwdriver

Declaration of conformity

We, Einhell UK Ltd Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom declare the conformity to UK standards and legislation was assessed for:

Car Hammer Screwdriver CC-HS 12/2 (Einhell)

UK legislation

Simple Pressure Vessels (Safety) Regulation X
Electrical Equipment (Safety) Regulation
Radio Equipment Regulation
Electromagnetic Compatibility
Regulation Measuring
Instruments Regulation Pressure
Equipment (Safety) Regulation
Personal Protective Equipment Regulation
The Ecodesign for Energy-Related Products and Energy Information Regulation
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation Noise Emission in the Environment by Equipment for use Outdoors Regulation
Annex V
Annex VI
Noise: measured LWA = dB (A); guaranteed LWA = dB (A) P = kW; L/Ø = cm
UK Approved Body:
Supply of Machinery (Safety) Regulation
Annex IV
UK Approved Body:
UKTE Certiﬁ cate No.: