Hunter 19339 19 Inch Jupiter Star Pendant Ceiling Light Instruction Manual
- June 4, 2024
- Hunter
Table of Contents
Hunter 19339 19 Inch Jupiter Star Pendant Ceiling Light
OVERVIEW
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning installation of the lighting fixture.
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the ceiling,
including the old mounting bracket. Remove the new mounting bracket assembly
from the bag. One end of the threaded post (H) should be attached to the
mounting bracket (A) with a hex nut (G) in place. The other end should be
connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the
canopy loop
(E). Depending on the placement of your junction box the position of threaded
post (H) may need to be adjusted to allow the canopy to be flush with the
ceiling. Determine this by lifting mounting bracket (A) up to the junction box
and place canopy (D) over the canopy loop (E) so that it is flush with the
ceiling. Adjust the position of threaded post (H) on the mounting bracket (A)
so that the canopy (D) covers at least half of the exterior threads on the
canopy loop (E) while it is securely connected to threaded post (H). The
threaded post (H) can be adjusted by loosening hex nut (G) to allow movement
of threaded post (H) on mounting bracket (A). Once the ideal position of the
threaded post (H) is determined, tighten up the hex nut (G) onto the threaded
post (H) just beneath the mounting bracket (A) to secure the threaded post in
place.
ASSEMBLING THE FIXTURE
There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten (some manual straightening of the downrods may be required). Thread the wires through spike (K) and screw it onto the threaded post (L) of the fixture. Thread the wires through and screw the rod to the threaded post of the spike (K). Pull the fixture wires through the canopy loop ring (F), the canopy (D), and the canopy loop (E). Screw the top rod to the canopy loop (E). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).
CONNECTING THE WIRES
Attach the fixture’s wires to the power supply wires from the junction box.
Connect black to black (Live); white to white (grounded); grounding to
grounding (green or copper). Twist the ends of the wire pairs together. Then,
twist on a wire connector. Make sure all twists are in the same direction.
Loop fixture’s ground wire around grounding screw (C) and tighten. If there is
no ground wire (green or copper) from the junction box, contact a qualified
electrician.
FINISHING THE INSTALLATION
Place the canopy (D) flush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw the canopy loop ring (F) onto the canopy loop (E) to properly secure the canopy (D) in place. Screw the decorative spikes (M) to the threaded posts (N) of the fixture. Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Your installation is now completed. Turn on the power and test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray the cleaner directly onto the fixture.
NOTICE In order to use a 12-in rod by itself you must first remove the post from the 6-in rod and install it on one of the ends of the 12-in rod.
Hunter Pro Tip: Twist or tape wire ends together to make it easier to pass them through the downloads. Threaded posts may also be removed for easier wire access.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>