saxby lighting Shield360 4CCT Tri Wattage Downlight Instruction Manual

: June 12, 2024
: saxby lighting

Table of Contents

Warning
Layout
Installation
Wiring
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Instruction manual
Shield360 4CCT Tri Wattage
103029, 106537

Thank you for purchasing this light ﬁtting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This light fitting is double insulated and does not require connection to an Earth circuit.
Please read these instructions carefully before commencing any work
This unit must be ﬁtted by a competent and qualiﬁed electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this ﬁtting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light ﬁtting should be connected to a circuit with a 30mA RCD ﬁtted.
If replacing an existing ﬁtting, make a careful note of the connections
This product is suitable for covering with insulation 300mm.
This product complies with Building Regulations Part B and is suitable for use in 90 minute fire rated ceilings.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part shouldbe scrapped.
The external ﬂexible cable or cord of this luminaire cannot be replaced. If the cord is damaged, the luminaire must be destroyed.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these ﬁttings carefully, ensuring the cables will reach the distances between each light ﬁtting.
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross section area of 1.0mm.
Cables must be protected using suitable conduit or plastic trunking.
When more than one downlight is installed, the minimum distance between units is 500mm. the unit must be located a 2 minimum distance of 50mm from a joist.
This product must be mounted out of arms reach.
This product has special protection against the ingress of moisture and is IP44 rated.
This product is suitable for use zone 2 and outside zones in a bathroom. Please see diagram.
If this unit is being ﬁtted in a room containing a bath or shower, a 30mA RCD must be used – in accordance with IEE regulations. saxby lighting Shield360
4CCT Tri Wattage Downlight - fig 1

Installation

Existing ﬁttings must be completely removed before installation of a new product. Before removing the existing ﬁtting, carefully note the position of each set of wires.
The ceiling surface must be ﬂat and smooth to ensure a good ﬁt.
Note that the switch is turned off before installation.
Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.

Cut a mounting hole 90mm diameter in the ceiling taking care not to foul any pipes, mains cables or joists beneath the surface (Ref. Fig.1). It is always recommended to cut the hole slightly smaller than the size specified, and then file the hole until the recessed unit fits snugly. Ensure a minimum ceiling void depth of 45mm is available.
Open the terminal block cover, Connect the mains supply cable into the terminals (Ref. Fig. 2).
Ref. Fig. 3. Choose your preferred wattage or colour before installing by wattage switch or CCT switch on the back of the product. Note: Befeore you change the wattage or colour, please turn off the power switch for safety.

The wattage is changeable between 4/6/8W using the wattage switch on the drive before installation.
The colour is changeable between 2700/3000/4000/6000K using the CCT switch on the drive before installation.

Push the spring clips upwards and fit into the ceiling hole, then push the unit up until firmly in position, ensuring that no cables are trapped. (Ref. Fig. 4).
Ensure that the product is sitting properly in the hole.
Switch on. Your light is now ready for use.

Wiring

Having correctly identiﬁed the wiring from your existing light ﬁtting, pull the mains wire through the hole and connect to the quick ﬁt connection block in the following way. Terminations:
Live supply to L = ( Brown or Red )
Earth to **= ( Green / Yellow )
Neutral to N = ( Blue or Black )
The terminal block allows for Loop-in / Loop-out connection.
Check that…**
You have correctly identiﬁed the wires.
The connections are tight.
No loose strands have been left out of the connection block.

Technical data

Supply Voltage: 220-240 V~, 50 Hz
Bulb Type: 4/6/8W LED SMD 4CCT, 2700/3000/4000/6000K
This product contains a light source of energy efficiency class E.
Non-replaceable light source
Non-replaceable control gear
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
The power supply is Double Insulated and does not require connection to an Earth circuit.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
This product is suitable for dimming.
This product is fire rated to 90 minutes.
This product is rated at IP44.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the ﬁnish.
For your safety, always switch off the power supply before cleaning.
For further information, please visit https://www.lighting-info.co.uk/103029