HOOVER CH50200 Commercial Superior Lite Upright Vacuum User Manual

SUPERIOR LITE
LIGHTWEIGHT VACUUM
USER MANUAL
MODEL: CH50200

IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE. THIS PRODUCT IS FOR COMMERCIAL USE ONLY. THIS PRODUCT CONTAINS NO SERVICEABLE PARTS.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS
READ ALL SAFETY WARNINGS AND INSTRUCTIONS BEFORE USING THIS PRODUCT.
WARNING: WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY, INCLUDING THE FOLLOWING:

• Fully assemble prior to use.
• Operate cleaner only at voltage specified on data plate on back of cleaner.
• Do not leave product when plugged in. Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Not intended for use by children age 12 and under. Close supervision is necessary when used by or near children. To avoid injury or damage, keep children away from product, and do not allow children to place fingers or other objects into any openings.
• Use only as described in this user’s manual. Use only Hoover® recommended attachments.
• Do not use product with damaged cord or plug. If product is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call customer service at 1-888-768-2014 prior to continuing use.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. Brush roll continues to rotate when in the upright position.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs. To avoid personal injury or damage, and to prevent the cleaner from falling, always place cleaner at bottom of stairs or on floor. Do not place cleaner on stairs or furniture, as it may result in injury or damage.
• Do not use to pick up flammable or combustible liquids, such as gasoline, or fine wood sandings, or use in areas where they may be present.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without bag in place.
• Your appliance is provided with an extension cord. In case of damage or loss of function, only replace this extension cord with an SJT type, rated 300 Volt – 105 degrees C (221 degrees F), 3 wire grounded, #18 AWG (American Wire Gauge), no longer than 50 feet. Failure to use the proper cord could result in fire or electric shock.
• Connect to properly grounded outlet only. See Grounding Instructions.

CAUTION: TO REDUCE THE RISK OF DAMAGE:

• Avoid picking up hard, sharp objects with this product, as they may cause damage.

• Store appropriately indoors in a dry place. Do not expose machine to freezing temperatures.

• Brush roll continues to turn while product is turned on and handle is in upright position.
  To avoid damage to carpet, rugs, and flooring, avoid tipping cleaner or setting it on furniture, fringed area rugs, or carpeted stairs during tool use.

• Do not use sharp objects to clean out hose as they can cause damage.

• With brush roll on, do not allow cleaner to sit in one location for an extended period of time, as damage to floor can result.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipmentgrounding conductor and  grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING: IMPROPER CONNECTION OF THE EQUIPMENT-GROUNDING CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE – IF IT WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY DUE TO A LOOSE ELECTRICAL CONNECTION BETWEEN THE APPLIANCE’S PLUG AND EXTENSION CORD, FIRMLY AND FULLY ATTACH THE APPLIANCE PLUG TO THE EXTENSION CORD. PERIODICALLY CHECK THE CONNECTION WHILE OPERATING TO ENSURE IT IS FULLY ATTACHED. DO NOT USE AN EXTENSION CORD THAT PROVIDES A LOOSE CONNECTION. A LOOSE CONNECTION MAY RESULT IN OVERHEATING, FIRE, AND INCREASES THE RISK OF A BURNING.
To reduce the risk of disconnection of the appliance cord from the extension cord during operating make a knot as shown in Figure 1.

This appliance is for use on a nominal 120-V circuit and has a grounding attachment plug that looks like the plug illustrated below. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adapter should be used with this appliance.

HAVE A QUESTION? HOOVER®
HAS THE ANSWER!
START WITH
HOOVERCOMMERCIAL.COM
DO NOT
RETURN TO STORE Start with 24/7 resources like these:
FAQs
HOW-TO-VIDEOS
TROUBLESHOOTING VIDEOS
Or call us and we’ll talk you through it.
CUSTOMER SUPPORT
1-888-768-2014
Mon-Fri, 8am-4pm CST

ASSEMBLY

FULLY ASSEMBLE PRODUCT PRIOR TO USE.
To assist you in identifying components of your vacuum, the parts have been numbered as follows:

1. Handle section,
   upper

2. Tube, lower

3.  Power head

4. Outer bag

5. Paper filter

6. Power cord

7. Retaining spring

8. Bag tension bar

9. Zip fastener

10. ON/OFF Switch

11.  Cord hook

12.  Plastic loop/cable clamp

13. Connector Assembly/ Rear Carry Handle

14. Fan housing

15. Cord assembly

16. Cord-Lock

17. Pigtail

18. Before assembling appliance, remove two screws from the connector assembly. Remove plastic insert by pulling upward.

19. With ON/OFF switch facing the front of the unit, slide upper handle section over matching section of the connector assembly. Place brace against handle and connection assembly aligning the holes. Insert one screw into top hole and one screw into the  bottom hole then tighten firmly until handle is no longer loose.

20. Attach cord to cord clip by pressing cord above and below clip ensuring the cord is fully rested in clip.

OPERATION

CAUTION: Use extra care when cleaning on stairs. To avoid personal injury or damage, and to prevent the cleaner from falling, always place cleaner at the bottom of the stairs or on the floor. Do not place cleaner on stairs or furniture, as it may result in injury or damage. When using tools, always ensure handle is in the upright position.

TO OPERATE
IMPORTANT: Make sure disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag.

OPERATING INSTRUCTIONS

1. Insert a new disposable paper filter dust bag— FIRST PUFF OUT and OPEN THE BAG. See “How To Replace Filter Dust Bag” in the Maintenance section of this manual.

2. Plug the power cord into an electrical outlet.

3.  Press the ON (l) – OFF (O) switch on Helping Handle Assembly, or on top of base for Straight Handle Models when ready to operate.

4. When the disposable filter dust bag is full, REPLACE IT.

5. If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service.

6. Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing.
   WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not covered under warranty.

7. Change the disposable filter dust bag at least once a month— even if it is not full! The collected dust in the dust bag can cause odor

8. DO NOT run the vacuum cleaner over cord. The revolving brush could damage the cord. Use caution when vacuuming over area rug edges & fringe.
   NOTE: Disposable paper filter dust bags play a very important role in the efficiency of your Hoover vacuum cleaner. If the filter bag becomes clogged, no air can pass through the cleaner and cleaning cannot take place, regardless of the cleaner’s power. To keep your cleaner operating at maximum efficiency, change the dust bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG.
   NOTE: Be sure the disposable paper filter dust  bag is installed properly. All paper dust bags arenot the same. Your Hoover disposable dust bags have been designed to be used with the Hoover cleaner. Using bags other than genuine Hoover disposable bags will affect the cleaning ability of your cleaner and may void the warranty.

MAINTENANCE

WARNING: Unplug cord from electrical outlet before servicing.

HOW TO REPLACE FILTER DUST BAG
BAG PART# AH10200

1.  Hook bottom of bag collar opening under lip “B” of connector assembly. Pull up on bag collar and snap over lip “A” of connector.

2. Press on edges of bag collar to insure bag is completely installed.
   IMPORTANT: Check to make sure bag collar is behind lips “A” and “B”. If it is not, dust will leak into outer bag. When filter bag is in place, close outer bag with zipper fastener.

GENERAL CLEANER CARE

At least once a month, check for and remove excessive lint, string or hair from revolving brush. Wipe the outside of the cleaner with a damp cloth. Also, clean the connector deflector assembly area, base of cleaner and fan housing area. If there is dust in the outer bag, vacuum it or shake it out. A little preventative maintenance will keep your cleaner looking new and will ensure continued cleaning effectiveness.
CAUTION: Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor Surfaces and Polished Floor Finishes Use low speed for hard surfaces and fine rugs.
Use floor and floor finish manufacturer’s recommended methods of cleaning. The metal strip on the base of the cleaner could be damaged if used on concrete or abrasive surfaces, and, therefore, cause damage to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished floor finishes. The roller brush may also scuff very soft finishes. Do not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation.

TO REPLACE FILTER DUST BAG
PART# AH10200.
STUFFING OR BLOCKAGE

Under certain conditions it is possible to stuff or block the intake tube and the lower tube assembly. If your vacuum cleaner does not pick up properly, makes an unusual noise or the outer bag does not fluff up or balloon open, follow these steps:

1.  Check for blockage at the mouth of the intake opening. See illustration A. If there is blockage, remove it with long-nose pliers, a screwdriver or coat hanger. If you can not reach the blockage, remove baseplate.

2. If the blockage is not at the base, remove lower tube. See illustration C. Unhook retainer spring, releasing bottom of bag. Twist lower collar counterclockwise to slide up. Pull tube out of base. Check for blockage. If blockage is in the tube, remove with a coat hanger.

3. If tube is not blocked, look into fan housing. Remove debris with long-nose pliers, a screwdriver or coat hanger.

WARNING: Unplug cord from
electrical outlet before servicing or removing cordlock.
ASSEMBLY:

1.  Connect plug and receptacle.
2. Snap cord into lock.
3.  Rotate insert until secure against plug.
4. Ensure rotation is as depicted to ensure proper engagement.

DISASSEMBLY:

1. Remove cord from lock
2. Disconnect plug and receptacle.

TO ADJUST OR REPLACE BRUSH PART # 430000880
WARNING: Unplug cord from electrical outlet before servicing.
To determine if the brush is worn, place a firm straight edge across the nozzle opening. If brush bristles do not extend beyond baseplate, brush should be adjusted.

1. Remove the baseplate by removing 5 screws.
   Then, remove the belt and brush roll from the housing.

2. Rotate both bearing assemblies at ends of brush roll to show “OLD” and replace in the holding channels in the housing.
   NOTE: The bearing assembly setting marked “OLD” has two notches ( l l ) on the top of the assembly. The one marked “NEW” has one notch ( l ). When rotating bearings, make sure both bearing assembly settings are the same and face up when replacing the brush roll.

3. Reassemble the belt and the baseplate and check bristle height above baseplate at each end of brush. If a previous adjustment has already been made and bristle height does not extend above baseplate, a new brush assembly should be ordered.

IMPORTANT: Unless the brush is worn as indicated above, both bearings must be in the “NEW” position. When rotating, both bearings must be in the “OLD” position. Unmatched settings will cause damage to your machine.
LUBRICATION: The motor and brush roll are equipped with bearings which contain sufficienlubrication for their lifetime. The addition of lubricant could cause damage. Do not add lubricant to motor or brush roll.

TROUBLESHOOTING

SAVE SERVICE CALLS CHECK THESE FIRST:

• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake opening, fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
• Does the brush turn freely? Are hair, string or rug fibers wound around the brush?

TROUBLESHOOTING
AVAILABLE REPLACEMENT PARTS AND ACCESSORIES SUCH AS FILTER BAGS AND BELTS CAN BE FOUND ON HOOVER.COM IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-888-768-2014 PRIOR TO CONTINUING USE. ALWAYS IDENTIFY YOUR CLEANER BY THE COMPLETE MODEL NUMBER. (THE MODEL NUMBER APPEARS ON THE BOTTOM OF THE CLEANER.)
ACCESSORIES
GENUINE PARTS AND ACCESSORIES: WE RECOMMEND USING ONLY WITH GENUINE HOOVER® REPLACEMENT BAGS
(FOR HOOVER BAGGED UPRIGHTS), PARTS, AND ACCESSORIES. DAMAGE CAUSED BY USE WITH OTHER THAN GENUINE HOOVER®
BAGS, PARTS, AND ACCESSORIES IS NOT COVERED BY AND MAY VOID YOUR WARRANTY.

WARNING: To reduce the risk of electric shock or injury from moving parts unplug before cleaning or servicing.
CAUTION: To reduce the risk of injury from moving parts – Unplug before servicing. Do not use cleaner without brushes in place.

into wall outlet.
2. No electricity in wall outlet.| 2.Checked electrical source – fuse or circuit breaker.
3.Brush roll is jammed and motor shut off.| 3. Clear obstruction. Upright can be
reset by unplugging or switching the on/off button once.
1. Filter bag is full.| 1. Replace filter bag. See “To install
paper filter bag dust bag:
2. Nozzle or intake pivot
clogged.| 2.Clear obstruction.
3.Brush is worn.| 3. See “To replace or adjust brush:
4. Too clogged.| 4. Clear obstruction.
5. Big pores are clogged with
fine dust.| 5. Change bag.
6. Impeller fan is broken.| 6. Return to service center for
repair.

ACCESSORIES SOLD SEPARATELY
COMMERCIAL: 1-888-768-2014

LIMITED WARRANTY FOR HOOVER® PRODUCT

1 YEAR LIMITED WARRANTY
Failure to register the product does not diminish product warranty rights.
WHAT THIS WARRANTY COVERS: When used and maintained in normal Commercial use and in accordance with the User’s Manual, your Royal Appliance Mfg. Co. product is warranted against original defects in material and workmanship for a full one year from date of purchase (the “Warranty Period”). During the Warranty Period, as described in this Warranty, Royal Appliance Mfg. Co. will provide labor and parts, at no cost to you, to correct any such defect in products purchased in the United States, U.S. Military Exchanges and Canada.
HOW TO MAKE A WARRANTY CLAIM: If this product is not as warranted, take or send the product to a Hoover® Commercial Authorized Warranty Service Dealer along with proof of purchase. For an automated referral to authorized service outlets, phone: 1-888-768-2014. For additional assistance or information concerning this Warranty or the availability of warranty  service outlets, phone 1-888-768-2014, Mon-Fri 8am-4pm CST.
WHAT THIS WARRANTY DOES NOT COVER:
Certain parts for your Royal Appliance Mfg. Co. product require replacement in the ordinary course of use due to normal wear. These items include filters (after 90 days of purchase unless damaged by defect of another warrantable component), belts (after 90 days of purchase unless damaged by defect of another warrantable component), brushrolls or agitators (after 90 days of purchase unless damaged by defect of another warrantable component), and housings. These parts are not covered by this Warranty.
This Warranty also does not cover: improper maintenance This warranty does not cover filters, improper maintenance of the product, damage due to misuse, acts of God, nature, vandalism or other acts beyond the control of Royal Appliance Mfg. Co., owner’s acts or omissions, use outside the country in which the product was initially purchased and resales of the product by the original owner defects or damages caused by repair or alteration by anyone other than an Authorized Hoover Warranty Service Dealer. Royal Appliance Mfg. Co. reserves the right to inspect any alleged defective product and make final decisions on any warranty claim. This warranty  does not cover pick up, delivery, transportation or house calls. However, if you mail your product to a Service Center for warranty service, cost of shipping will be paid one way. Please call Hoover Commercial Customer Services at 1-888-768-2014 for instructions on how to ship this product. This warranty does not apply to products purchased outside the United States (including its territories and possessions), a U.S. Military Exchange and Canada.
OTHER IMPORTANT TERMS: This warranty is not transferable and may not be assigned. This Warranty shall be governed and construed under the laws of the state of North Carolina. The Warranty Period will not be extended by any replacement of batteries or parts or repair performed under this Warranty.
THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY. ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, ARE DISCLAIMED. IN NO EVENT WILL Hoover Commercial BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER OR ANY PARTY CLAIMING THROUGH OWNER, WHETHER BASED IN CONTRACT, NEGLIGENCE, TORT OR STRICT PRODUCTS LIABILITY OR ARISING FROM ANY CAUSE WHATSOEVER EVEN IF THIS WARRANTY FAILS OF ITS ESSENTIAL PURPOSE. TO THE EXTENT PERMITTED BY APPLICABLE LAW, NO WARRANTIES  THAT ARISE BY OPERATION OF LAW, IF APPLICABLE, SHOULD EXCEED THE DURATION OF THE LIMITED WARRANTY PROVIDED HEREIN. Some states do not allow the exclusion of consequential damages, so the above exclusion may not apply to you. This warranty gives you specific rights; you may also have others that vary from state to state.

References

• Vacuum Cleaners | Carpet Cleaners | Hard Floor Cleaners | Hoover
• Parts Finder & Support Library – Hoover
• Hoover Commercial Information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>