Harley Benton 50M-B Power Spaceship User Guide

: June 12, 2024
: Harley Benton

Table of Contents

Harley Benton 50M-B Power Spaceship
Product Information
Safety Instructions
Features
Scope of Delivery
Product Usage Instructions
**Operating elements
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Harley Benton 50M-B Power Spaceship

Harley-Benton-50M-B-Power-Spaceship-PRODUCT

Product Information

The Spaceship Power 50M-B is a multiple power supply designed for effects pedals. It provides various voltage outputs to power different devices. The power supply comes with a power adapter and features insulated and uninsulated outputs.

Safety Instructions

Ensure that plastic bags, packaging, etc. are disposed of properly and are out of reach of babies and young children to prevent choking hazards.
Do not let children use electrical devices unsupervised.
Avoid direct contact between the rubber feet of the product and surfaces as they may cause permanent dark stains. Use felt-pad floor protectors or similar underlays if needed.
Avoid using liquid cleaners such as benzene, thinners, or flammable cleaning agents on the product.

Features

1 USB-A output, uninsulated
2 USB-C output, uninsulated
1 socket for the supplied power adapter for power supply and
charging
1 mains switch
1 output with 24 V @ 2000 mA, uninsulated
1 output with 9 V @ 3000 mA, uninsulated
2 outputs with 9 V @ 250 mA, insulated
3 outputs with 9 V @ 500 mA, insulated
2 outputs with voltage switches, insulated, switchable between
9 V @ 500 mA / 12 V @ 375 mA / 18 V @ 250 mA
Control LED for outputs 1 – 9, lights up green when voltage is
present, turns off when output is deactivated due to overload

Scope of Delivery

The product comes with the following items:

Spaceship Power 50M-B
Power adapter

Product Usage Instructions

Connect the supplied power adapter to the device.
Press the mains switch to switch on the device.
Connect effects pedals or devices requiring 24 V supply voltage (up to 2000 mA) to output 1 using a suitable voltage supply cable.
Connect devices with high power consumption (i.e., multi-effect devices) requiring 9 V supply voltage (up to 3000 mA) to output 2 using a suitable voltage supply cable.
Connect effects pedals or devices requiring 9 V supply voltage (up to 250 mA) to outputs 3 – 4 using suitable voltage supply cables.
Connect effects pedals or devices requiring 9 V supply voltage (up to 500 mA) to outputs 5 – 7 using suitable voltage supply cables.
Ensure that the polarity of the devices being connected matches the polarity of the power supply outputs to prevent property damage by polarity reversal.
Connect effects pedals or devices requiring 9 V, 12 V, or 18 V supply voltage (up to 500 mA, 375 mA, or 250 mA respectively) to outputs 8 – 9 using suitable voltage supply cables. Set the associated switch above the output to the position corresponding to the required voltage.
Do not exceed the maximum output power of 31.5 W.

Quick Start Guide
This quick start guide contains important information on the safe operation of the product. Read and follow the safety advices and instructions given. Retain the quick start guide for future reference. If you pass the product on to others please include this quick start guide.

Safety instructions
Intended use This product is intended to be used as a multiple power supply for effects pedals. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
Danger for children Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow the pieces and choke! Never let children unattended use electrical devices.
Possible staining The plasticiser contained in the rubber feet of this product may possibly react with the coating of your surface and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the surface and use a suitable underlay if necessary, i.e. felt- pad floor protectors or similar.

Where to use the product
Never use the product
- in conditions of extreme temperature or humidity
- in extremely dusty or dirty areas
- at locations where the unit can become wet
General handling
- To prevent damage, never use force when handling the product.
- Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.

Incorrect handling of lithium batteries can result in injury

In the event of a short circuit, overheating or mechanical damage, lithium batteries can cause severe injuries.
When handled correctly and appropriately lithium batteries pose no risk.
Store lithium batteries in a cool, dry place, ideally in the original packaging.
Store lithium batteries away from heat sources (e.g. radiators or sunlight). Lithium batteries are hermetically sealed. Never attempt to open a lithium battery.
If the battery housing is damaged small amounts of the electrolyte may leak out. If this should happen, seal the lithium battery in airtight packaging and wipe up the traces of electrolyte using absorbent paper towels. You must wear protective rubber gloves when doing so. Clean your hands and the affected surface thoroughly with cold water.
Never attempt to recharge non-rechargeable lithium batteries. When charging lithium batteries you must use a suitable charging device intended for the purpose.
Before disposing of the device remove the lithium batteries. Protect used lithium batteries against potential short circuits, e.g. by covering the poles with adhesive tape.
Only use powder extinguishers or other suitable extinguishing agents to extinguish a burning lithium battery.

Features

Lightweight, compact pedalboard
Battery or mains powered
Powder-coated aluminium frame
7 insulated, filtered and short-circuit-proof outputs eliminate noise and hum
4 uninsulated outputs for multi-effect devices or for charging smartphones or tablets
Incl. power adapter for power supply and charging
With volt/current meter
High current output for modern digital effects
LED indicator on each output

Scope of delivery

3 × DC cable with a length of 30 cm
3 × DC cable with a length of 60 cm
3 × DC cable with a length of 90 cm
1 × reverse polarity cable with red plug
1 × battery clip
1 × connector cable with a length of 45 cm with 5.5 × 2.5 mm green coaxial plug to 5.5 × 2.1 mm coaxial plug
1 × connector cable with a length of 45 cm with 3.5 mm jack plug to 5.5 × 2.1 mm coaxial plug
1 × voltage boost cable, 20 cm
1 × current boost cable, 60 cm
1 × EIAJ-05 cable
1 × power adapter with EU plug, 120 cm
1 × cable fastening set
1 × velcro tape, self-adhesive, 200 cm × 4.5 cm
1 × Allen key (5 mm)
1 × transport bag with storage pocket and shoulder strap

**Operating elements

Harley-Benton-50M-B-Power-Spaceship-
FIG-1 **

USB-A output, uninsulated
USB-C output, uninsulated
Socket for the supplied power adapter for power supply and charging
Mains switch
Output 1 with 24 V @ 2000 mA, uninsulated
Output 2 with 9 V @ 3000 mA, uninsulated
Outputs 3 – 4 with each 9 V @ 250 mA, insulated
Outputs 5 – 7 with each 9 V @ 500 mA, insulated
Outputs 8 – 9 with voltage switches, insulated, switchable between 9 V @ 500 mA / 12 V @ 375 mA / 18 V @ 250 mA
Control LED for outputs 1 – 9, lights up green when voltage is present, turns off when output is deactivated due to overload

Using the product

Use the supplied power adapter to connect the device to the power and press the mains switch to switch on the device.
Use a suitable voltage supply cable to connect effects pedals or similar devices which require 24 V supply voltage at a maximum of 2000 mA to the output 1.
Use a suitable voltage supply cable to connect devices with high power consumption (i. e. multi-effect devices) which require 9 V supply voltage at a maximum of 3000 mA to the output 2.
Use suitable voltage supply cables to connect effects pedals or similar devices which require 9 V supply voltage at a maximum of 250 mA to the outputs 3 – 4.
Use suitable voltage supply cables to connect effects pedals or similar devices which require 9 V supply voltage at a maximum of 500 mA to the outputs 5 – 7.
Danger of property damage by polarity reversal
Make sure that the polarity of the devices to be connected must be
the same as the polarity of the power supply outputs ( ). Powering a device with polarity-reversed voltage may damage it!
Use suitable voltage supply cables to connect effects pedals or similar devices which require 9 V ,12 V or 18 V supply voltage at a maximum of 500 mA, 375 mA or 250 mA to the outputs 8 – 9. Set the associated switch above the output to the position of the required voltage. The maximum output power of 31.5 W must not be exceeded.
Danger of property damage by overvoltage Make sure that connected devices are actually suitable for the set voltage. To power a device with overvoltage may damage it!
Use suitable voltage supply cables to connect devices as smartphones or tablets to the USB outputs.
Each operational output 1 – 9 is indicated by a green LED. If an output is switched off due to overload, the LED turns off. Then disconnect the respective pedal from the device. After approx. 2 seconds, the normal voltage supply is restored here.
Press the mains switch to switch off the device.

Technical specifications

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Only dispose of lithium batteries when they are discharged. Remove replaceable lithium batteries from the device before disposal. Protect used lithium batteries against short circuits, for example by covering the poles with adhesive tape. Permanently built-in lithium batteries must be disposed of together with the device. Please inquire about an appropriate collection point.

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.