Uniden App 4K Dome Camera User Guide
- June 12, 2024
- Uniden
Table of Contents
Uniden App 4K Dome Camera User Guide
What’s in the Box
Uniden App 4K Dome x1
Weatherproof Lid x1
1m Ethernet Cable x1
Quick Start Guide x1
Screw Kit x1
Mounting Template x1
General Introduction
Camera Connection
Before using the camera, please connect the camera to App Cam 4K NVR.
Note:
The camera should be powered with a Uniden App Cam 4K NVR (not included in the
package). Please set up the camera via the NVR interface
Mount the Camera
Installation Tips
- Do not face the camera towards any light sources.
- Do not point the camera towards a glass window. Or, it may result in poor image quality because of the window glare by infrared LEDs, ambient lights or status lights.
- Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may result in poor image quality. To ensure best image quality, the lighting condition for both the camera and the capture object shall be the same.
- To ensure better image quality, it’s recommended to clean the lens with a soft cloth from time to time.
- Make sure the power ports are not directly exposed to water or moisture and not blocked by dirt or other elements.
- With IP weatherproof ratings, the camera can work properly under conditions like rain and snow. However, it doesn’t mean the camera can work underwater.
- Do not install the camera at places where rain and snow can hit the lens directly
Installation Tips
Step 1
Drill holes in accordance with the mounting hole template.
NOTE: Use the drywall anchors included in the package if needed.
Step 2
Install the mount base with the mounting screws included in the package.
NOTE: Run the cable through the cable notch on the mount base.
Step 3
To get the best field of view, loosen the adjustment knob on security mount
and turn the camera.
Step 4
Stiffen the adjustment knob to lock the camera.
Troubleshooting
Camera is not turning on
If your camera is not powering on, please try the following solutions:
- Make sure your camera is powered properly. The camera should be powered by the Uniden App Cam 4K NVR or a 12V power adapter.
- If the camera is connected to a PoE device as listed above, connect the camera to another PoE port and see if the camera will power on.
- Try again with another Ethernet cable.
Infrared LEDs Stop Working
If the Infrared LEDs of your camera stop working, please try the following
solutions:
- Enable infrared lights on Device Settings page via Uniden Solo App.
- Check if the Day/Night mode is enabled and set up auto infrared lights at night on Live View page via Uniden Solo App.
- Upgrade the firmware of your camera to the latest version.
- Restore the camera to factory settings and check out the infrared light settings again.
If there are more support needed, please contact Uniden Support
Specifications
Video & Audio|
Model
|
App Cam 4K Dome
---|---|---
Image Sensor| 1/2.49” CMOS Sensor
Video Resolution| up to 3840×2160 (8MP) 4K up to 25 fps
Video Compression| H.264/H.265
Viewing Angle| Horizontal: 87° Vertical: 44°
Night Vision| Up to 30 Meters
Audio| Two-way talk
Alerts| Person detection; vehicle detection; motion detection
Network| Ethernet| One 10M/100Mbps; RJ45
Hardware| PoE| IEEE 802.3af
DC Power| Can be powerd by 12V/1A power adaptor
Storage| Supports up to 256GB micro SD card, min class 10*
**Other Parameters**| Temperature| Operating Temperature : -10°C~+55°C
Operating Humidity| 10% to 90%
Waterproof Level| IP66 Weatherproof
Note: When the camera is connected to the NVR, the SD Card storage option is not supported on the App and the NVR itself. Only supports recording to fat32 SD Card when setup as a standalone camera.
Uniden App Cam 4K Dome
Important:
Satisfactory evidence of the original purchase is required for warranty
service. Please refer to our Uniden website for any details or warranty
durations offered in addition to those contained below.
Warrantor
The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”).
Terms of Warranty : Uniden Aust warrants to the original retail purchaser
only that the Uniden App Cam 4K Dome (“the Product”), will be free from
defects in materials and craftsmanship for the duration of the warranty
period, subject to the limitations and exclusions set out below.
Warranty Period: This warranty to the original retail purchaser is only
valid in the original country of purchase for a Product first purchased either
in Australia or New Zealand and will expire, as indicated below, from the date
of original retail sale
| Product | 1 Year |
|---|---|
| Accessories | 90 Days |
If a warranty claim is made, this warranty will not apply if the Product is found by Uniden to be:
A. Damaged or not maintained in a reasonable manner or as recommended in
the relevant Owner’s Manual;
B. Modified, altered or used as part of any conversion kits,
subassemblies or any configurations not sold by Uniden Aust;
C. Improperly installed contrary to instructions contained in the
relevant Owner’s Manual
D. Repaired by someone other than an authorized Uniden Repair Agent in
relation to a defect or malfunction covered by this warranty; or
E. Used in conjunction with any equipment, parts or a system not
manufactured by Uniden.
Parts Covered : This warranty covers the Product and included accessories
User-generated Data : This warranty does not cover any claimed loss of or damage to user-generated data (including but without limitation phone numbers, addresses and images)that may be stored on your Product.
Statement of Remedy : If the Product is found not to conform to this warranty as stated above, the Warrantor, at its discretion, will either repair the defect or replace the Product without any charge for parts or service. This warranty does not include any reimbursement or payment of any consequential damages claimed to arise from a Product’s failure to comply with the warranty.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty is in addition to and sits alongside your rights under either the COMPETITION AND CONSUMER ACT 2010 (Australia) or the CONSUMER GUARANTEES ACT (New Zealand) as the case may be, none of which can be excluded.
Procedure for Obtaining Warranty Service : Depending on the country in which the Product was first purchased, if you believe that your Product does not conform with this warranty, you should deliver the Product, together with satisfactory evidence of your original purchase (such as a legible copy of the sales docket) to Uniden. Please refer to the Uniden website for address details. You should contact Uniden regarding any compensation that may be payable for your expenses incurred in making a warranty claim. Prior to delivery, we recommend that you make a backup copy of any phone numbers, images or other data stored on your Product, in case it is lost or damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD
Phone number : 1300 366 895
Email address : [email protected]
