Harley Benton StreetBox-60 Battery Powered Speaker User Manual

StreetBox-60
Battery-powered Speaker
User Manual

General information

This user manual contains important information on the safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future reference. Make sure that it is available to all persons using this device. If you sell the device to another user, be sure that they also receive this manual.
Our products and user manuals are subject to a process of continuous development. We there‐ fore reserve the right to make changes without notice. Please refer to the latest version of the user manual which is ready for download under www.thomann.de.
1.1 Further information
On our website (www.thomann.de) you will find lots of further information and details on the following points:

topics of interest for you quickly.
Online guides| Our online guides provide detailed information on technical basics and terms.
Personal consultation| For personal consultation please contact our technical hotline.
Service| If you have any problems with the device the customer service will gladly assist you.

1.2 Notational conventions
This manual uses the following notational conventions:
Letterings
The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
Displays
Texts and values displayed on the device are marked by quotation marks and italics.
Examples: ‘24ch’ , ‘OFF’ .
1.3 Symbols and signal words
In this section you will find an overview of the meaning of symbols and signal words that are used in this manual.

immediate dangerous situation that will result in death or serious injury if it is not avoided.
WARNING!| This combination of symbol and signal word indicates a pos‐sable dangerous situation that can result in death or serious injury if it is not avoided.
CAUTION!| This combination of symbol and signal word indicates a possible dangerous situation that can result in minor injury if it is not avoided.
NOTICE!| This combination of symbol and signal word indicates a possible dangerous situation that can result in material and environmental damage if it is not avoided.
Warning signs| Type of danger
| Warning – high-voltage.
| Warning – danger zone.

Safety instructions

Intended use
This device is designed for sound reinforcement. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices.
DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device if covers, protectors or optical components are missing or damaged.
WARNING!
Incorrect handling of lithium batteries can result in injury
In the event of a short circuit, overheating or mechanical damage, lithium batteries can cause severe injuries. Follow the advice on the correct handling of lithium batteries in the present section.
CAUTION!
Possible hearing damage
The device can produce volume levels that may cause temporary or permanent hearing impairment. Over an extended period of time, even levels that seem to be uncritical can cause hearing damage. Decrease the volume level immediately if you experience
ringing in your ears or hearing impairment. If this is not possible, keep a greater distance or use sufficient ear protectors.
NOTICE!
Risk of fire
Do not block areas of ventilation. Do not install the device near any direct heat source. Keep the device away from naked flames.
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions specified in the chapter
‘Technical specifications’ of this user manual. Avoid heavy temperature fluctuations and do not switch the device on immediately after it was exposed to temperature fluctuations (for example after transport at low outside temperatures). Dust and dirt inside can
damage the unit. When operated in harmful ambient conditions (dust, smoke, nicotine, fog, etc.), the unit should be maintained by qualified service personnel at regular intervals to prevent overheating and other malfunction.
NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the external power supply, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker. Failure to do so could result in damage to the device and possibly the user. Unplug the external power supply before electrical storms occur and when the device is unused for long periods of time to reduce the risk of electric shock or fire.
NOTICE!
Possible damage to lithium-ion batteries through incorrect storage
By deep discharge, lithium-ion batteries can be permanently damaged or lose some of their capacity. Before long breaks, charge the batteries to around 50 % of their capacity and then switch off the device. Store the device at room temperature or cooler in an envi‐ ronment as dry as possible. If the batteries are stored for a longer period, recharge them to 50 % every three months. Fully charge the batteries only shortly before use at room temperature.
NOTICE!
Possible staining
The plasticizer contained in the rubber feet of this product may possibly react with the coating of your surface and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the surface and use a suitable underlay if  necessary, i.e. felt pads or similar.

Features

Compact portable battery-powered amplifier with great features for playing and singing along with streamed music via the built-in Bluetooth function; ideal for electric guitar, acoustic guitar, ukulele, vocals and music.
Special features of the device:

• Built-in Bluetooth function

• 60 watt RMS

• 2 × 5.5 inch full-range speaker

• Connections:
  – Microphone input, designed as XLR / 1/4″ jack combo socket
  – Instrument / microphone input, designed as 1/4″ jack socket
  – Instrument input, designed as 1/4″ jack socket
  – Amp in and output, designed as 3.5 mm jack socket

• Guitar / Microphone, Bass, Mid, Treble, Reverb and Master Volume controls

• Built-in compressor to protect speakers and prevent distortion

• Plug-in power supply and gigbag included

Installation and starting up

Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.
Create all connections while the device is off. Use the shortest possible high-quality cables for all connections. Take care when running the cables to prevent tripping hazards.
NOTICE!
Possible property damage by magnetic fields
Loudspeakers produce a static magnetic field. Therefore, maintain an appropriate distance to devices that can be adversely affected or damaged by an external magnetic field.
4.1 Battery operation
You can also operate the device independently of the mains power supply via the built-in rechargeable lithium battery (lithium-ion accumulator 18.5 V, 2.2 Ah).
4.1.1 Dealing with lithium batteries
WARNING!
Incorrect handling of lithium batteries can result in injury In the event of a short circuit, overheating or mechanical damage, lithium bat‐teries can cause severe injuries.
Follow the advice on the correct handling of lithium batteries in the present sec‐tion.
When handled correctly and appropriately lithium batteries pose no risk.
Store lithium batteries in a cool, dry place, ideally in the original packaging.
Store lithium batteries away from heat sources (e.g. radiators or sunlight). Lithium batteries are hermetically sealed. Never attempt to open a lithium battery.
If the battery housing is damaged small amounts of the electrolyte may leak out. If this should happen, seal the lithium battery in airtight packaging and wipe up the traces of electrolyte using absorbent paper towels. You must wear protective rubber gloves when doing so. Clean your hands and the affected surface thoroughly with cold water.
Never attempt to recharge non-rechargeable lithium batteries. When charging lithium bat‐teries you must use a suitable charging device intended for the purpose.
Before disposing of the device remove the lithium batteries. Protect used lithium batteries against potential short circuits, e.g. by covering the poles with adhesive tape.
Only use powder extinguishers or other suitable extinguishing agents to extinguish a burning lithium battery.
4.2 Connection options

Connections and controls

Pressed: Passive pickup
Not pressed: Active pickup
3| [ACOUSTIC GUITAR] | control for the instrument input
• [BASS] | bass control
• [MIDDLE] | mids control
•  [TREBLE] | treble control
•  [VOLUME] | volume control
• [REVERB] | control for reverb effect intensity
4| [NOTCH] | control for setting the anti-feedback filter
•  [FREQ.] | filter centre frequency
•  [DEPTH] | filter quality
5| [AMP] | connections for another device of the same type. When two devices are connected together, the second device will automatically adjust the volume, tone, and effects of the first device.
• [IN] | input, designed as 3.5 mm jack socket (stereo)
• [OUT] | output, designed as 3.5 mm jack socket (stereo)
6| Connector for the supplied power adapter for power supply
7| State of charge indicators. All three LEDs light up when battery is fully charged. When capacity decreases, the LEDs [FULL] , [70%] and [LOW] go out one by one. If only the [LOW] LED lights up, the remaining battery capacity is low. Then connect the device to the mains power to charge the battery.
---|---
8| [POWER] | main switch, turns the device on and off
9| [BLUETOOTH] •  [VOLUME] | volume control
•  [ON/OFF] | Bluetooth connection control
To establish a Bluetooth connection, press and hold [ON/OFF] for 2 seconds to search for Bluetooth-enabled devices ready for pairing. The LED flashes blue. The Bluetooth list of the device to be paired displays ‘AG-60A’. Accept the connection. For IOS devices the code 0000 must be entered. A short beep sounds when the connec‐tion is successfully established. The LED lights up solid blue.
10| [MASTER] | master volume control
11| Instrument / microphone input, designed as 1/4″ jack socket (mono)
12| [Mode Select] | switch for the sensitivity of the instrument / microphone input Pressed: Instrument
Not pressed: Microphone
13| [MIC / ACOUSTIC GUITAR] | control for the instrument / microphone input
•  [BASS] | bass control
•  [MIDDLE] | mids control
•  [TREBLE] | treble control
•  [VOLUME] | volume control
•  [REVERB] | control for echo and reverb effect intensity
---|---
14| Microphone input, designed as XLR / ¼” jack combo
15| [MICROPHONE] | control for the microphone input
[BASS] | bass control
•  [MIDDLE] | mids control
•  [TREBLE] | treble control
•  [VOLUME] | volume control

Technical specifications

 Capacity

1 × XLR / 1/4″ jack combo socket, mono
Pairing with second unit| 1 × 3.5 mm jack socket, stereo
Output connections| Pairing with second unit| 1 × 3.5 mm jack socket, stereo
Output power| 60 W (RMS)
Frequency range| 80 Hz … 20 kHz
Sound pressure level (SPL)| –111 dB (@ 1 kHz)
Bluetooth®| Frequency range| 2.400 GHz … 2.4835 GHz
Max. transmission power| 10 mW
Power supply| External power adapter, 100 – 240 V     50/60 Hz
Operating voltage| 24 V    / 1500 mA, centre positive
Battery / rechargeable battery| Battery type| Lithium-ion
Voltage| 18.5 V
| Capacity| 2200 mAh
Operating time| 5 h
Charging time in the device| 3 h
Dimensions (W × H × D)| 375 mm × 195 mm × 185 mm
Weight| 4.0 kg
Ambient conditions| Temperature range| –20 °C…60 °C
Relative humidity| 20 %…80 % (non-condensing)

Further information

Plug and connection assignment

Introduction
This chapter will help you select the right cables and plugs to connect your valuable equip‐ment in such a way that a perfect sound experience is ensured.
Please note these advices, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into the socket, an incorrect connection may result in a destroyed power amp, a short circuit or ‘just’ in poor transmission quality!
Balanced and unbalanced trans‐mission
Unbalanced transmission is mainly used in semi-professional environment and in hifi use.
Instrument cables with two conductors (one core plus shielding) are typical representatives of the unbalanced transmission. One conductor is ground and shielding while the signal is trans‐mitted through the core.
Unbalanced transmission is susceptible to electromagnetic interference, especially at low levels, such as microphone signals and when using long cables.
In a professional environment, therefore, the balanced transmission is preferred, because this enables an undisturbed transmission of signals over long distances. In addition to the conduce‐tors ‘Ground’ and ‘Signal’, in a balanced transmission a second core is added. This also transfers the signal, but phase-shifted by 180°.
Since the interference affects both cores equally, by subtracting the phase- shifted signals, the interfering signal is completely neutralized. The result is a pure signal without any noise inter‐refence.
1/4″ TS phone plug (mono, unbalanced)

1. Signal
2. Ground, shielding

1/4″ TRS phone plug (mono, balanced)

1. Signal (in phase, +)
2. Signal (out of phase, –)
3. Ground

Three-pole 1/8″ mini phone jack (stereo, unbalanced)

1. Signal (left)
2. Signal (right)
3. Ground, shielding

XLR plug (balanced)

1. Ground, shielding
2. Signal (in phase, +)
3. Signal (out of phase, –)
4. Shielding on plug housing (option)

Protecting the environment

Disposal of the packaging mate‐rial
** For the packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Disposal of batteries
Batteries must not be thrown away or incinerated; they must be disposed of in accordance with local regulations for the disposal of hazardous waste. Use the existing collection points for this.
Only dispose of lithium batteries when they are discharged. Remove replaceable lithium bat‐teries from the device before disposal. Protect used lithium batteries against short circuits, for example by covering the poles with adhesive tape. Permanently built-in lithium batteries must be disposed of together with the device. Please inquire about an appropriate collection point.
Disposal of your old device**
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.

StreetBox-60
Battery-powered Speaker

References

• Buy musical instruments online from the market leader – Thomann International

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>