Harley Benton 60-B Spaceship PowerBar User Guide

60-B Spaceship PowerBar
User Guide

Quick Start Guide
This quick start guide contains important information on the safe operation of the product. Read and follow the safety advices and instructions given. Retain the quick start guide for future reference. If you pass the product on to others please include this quick start guide.

Safety instructions

Intended use
This product is meant to be used as a multiple power supply for effects pedals. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow the pieces and choke! Never let children unattended use electrical devices.
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react with the coating of your surface and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the surface and use a suitable underlay if necessary, i.e. felt-pad floor protectors or similar.
Where to use the product
Never use the product

• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
• at locations where the unit can become wet

General handling

• To prevent damage, never use force when handling the product.
• Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.

Incorrect handling of lithium batteries can result in injury

In the event of a short circuit, overheating or mechanical damage, lithium batteries can cause severe injuries.

• When handled correctly and appropriately lithium batteries pose no risk.
• Store lithium batteries in a cool, dry place, ideally in the original packaging.
• Store lithium batteries away from heat sources (e.g. radiators or sunlight). Lithium batteries are hermetically sealed. Never attempt to open a lithium battery.
• If the battery housing is damaged small amounts of the electrolyte may leak out. If this should happen, seal the lithium battery in airtight packaging and wipe up the traces of electrolyte using absorbent paper towels. You must wear protective rubber gloves when doing so. Clean your hands and the affected surface thoroughly with cold water.
• Never attempt to recharge non-rechargeable lithium batteries. When charging lithium batteries you must use a suitable charging device intended for the purpose.
• Before disposing of the device remove the lithium batteries. Protect used lithium batteries against potential short circuits, e.g. by covering the poles with adhesive tape.
• Only use powder extinguishers or other suitable extinguishing agents to extinguish a burning lithium battery.

Features

• Special power adapter to connect and integrate with existing Harley Benton Spaceship 60 pedalboards
• Battery or mains powered
• 11 insulated, filtered and short-circuit proof outputs eliminate noise and hum
• 4 uninsulated outputs for multi-effect devices or for charging smartphones or tablets
• Incl. power adapter for power supply and charging
• With volt/current meter
• High current output for modern digital effects
• LED indicator on each output

Scope of delivery

• 4 × DC cable with a length of 30 cm
• 5 × DC cable with a length of 60 cm
• 4 × DC cable with a length of 90 cm
• 1 × reverse polarity cable with red plug
• 1 × battery clip
• 1 ×  connector cable with a length of 45 cm with 5.5 × 2.5 mm green coaxial plug to 5.5 × 2.1 mm coaxial plug
• 1 ×  connector cable with a length of 45 cm with 3.5 mm jack plug to 5.5 × 2.1 mm coaxial plug
• 1 × voltage boost cable, 20 cm
• 1 × current boost cable, 60 cm
• 1 × EIAJ-05 cable
• 1 × power adapter with EU plug, 120 cm
• 1 × cable fastening set
• 1 × velcro tape, self-adhesive, 100 cm × 4.5 cm
• 1 × Allen key (5 mm)
• 6 × screw
• 2 × rubber foot
• 1 × transport bag with storage pocket and shoulder strap
• 2 ×  aluminium edges for mounting the Powerbar or the Crossbars of existing Harley Benton Spaceship 60 Boards

Operating elements

1. USB-A output, uninsulated

2. USB-C output, uninsulated

3. Socket for the supplied power adapter for power supply and charging

4. Mains switch

5. Output 1 with 24 V @ 2000 mA, uninsulated

6. Output 2 with 9 V @ 3000 mA, uninsulated

7. Outputs 3 – 6 with each 9 V @ 250 mA, insulated

8. Outputs 7 – 9 with each 9 V @ 500 mA, insulated

9. Outputs 10 – 13 with voltage switches, insulated, switchable between
   9 V @ 500 mA /
   12 V @ 375 mA /
   18 V @ 250 mA

10. Control LED for outputs 1 – 13, lights up green when voltage is present, turns off when output is deactivated due to overload

Using the product

1. Use the supplied power adapter to connect the device to the power and press the mains switch to switch on the device.

2. Use a suitable voltage supply cable to connect effects pedals or similar devices which require 24 V supply voltage at a maximum of 2000 mA to the output 1.

3. Use a suitable voltage supply cable to connect devices with high power consumption (i. e. multi-effect devices) which require 9 V supply voltage at a maximum of 3000 mA to the output 2.

4. Use suitable voltage supply cables to connect effects pedals or similar devices which require 9 V supply voltage at a maximum of 250 mA to the outputs 3 – 6.

5. Use suitable voltage supply cables to connect effects pedals or similar devices which require 9 V supply voltage at a maximum of 500 mA to the outputs 7 – 9.
   Danger of property damage by polarity reversal
   Make sure that the polarity of the devices to be connected must be the same as the polarity of the power supply outputs ( ). To power a device with polarity-reversed voltage may damage it!

6. Use suitable voltage supply cables to connect effects pedals or similar devices which require 9 V ,12 V  or 18 V  supply voltage at a maximum of 500 mA, 375 mA or 250 mA to the outputs 10 – 13. Set the associated switch above the output to the position of the required voltage. The maximum output power of 45 W must not be exceeded.
   Danger of property damage by overvoltage
   Make sure that connected devices are actually suitable for the set voltage. To power a device with overvoltage may damage it!

7. Use suitable voltage supply cables to connect devices as smartphones or tablets to the USB outputs.

8. Each operational output 1 – 13 is indicated by a green LED. If an output is switched off due to overload, the LED turns off. Then disconnect the respective pedal from the device. After approx. 2 seconds, the normal voltage supply is restored here.

9. Press the mains switch to switch off the device.

Technical specifications

• Connections ( )
  – Output 1: 24 V @ max. 2000 mA
  – Output 2: 9 V @ max. 3000 mA
  – Outputs 3: – 6 9 V @ max. 250 mA (individually insulated)
  – Outputs 7: – 9 9 V @ max. 500 mA (individually insulated)
  – Outputs 10: – 13switchable 9 / 12 / 18 V @ max. 500 / 375 / 250 mA (individually insulated)

• USB output
  USB-C max. 18 W
  USB-A max. 18 W

• Power output: 45 W

• Current output: 3750 mA

• Power supply: External power adapter, 100 – 240 V ~ 50/60 Hz

• Operating voltage: 24 V / 2 A, centre negative

• Battery
  Battery type: Lithium-ion
  Voltage: 7.4 V
  Capacity: 9000 mAh
  Operating time: 1.1 h (after 3.4 h charging time)

• Dimensions (W × H × D)
  600 mm × 30 mm × 50 mm
  23.62″ × 1.18″ × 1.96″

• Weight: 950 g

• Ambient conditions:
  Temperature range 0 °C…40 °C
  Relative humidity 20 %…80 %
  (non-condensing)

**** For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Only dispose of lithium batteries when they are discharged. Remove replaceable lithium batteries from the device before disposal. Protect used lithium batteries against short circuits, for example by covering the poles with adhesive tape. Permanently built-in lithium batteries must be disposed of together with the device. Please inquire about an appropriate collection point.
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
www.thomann.de
info@thomann.de
DocID: 521011_19.09.2022

References

• Buy musical instruments online from the market leader – Thomann United States

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>