marta MT-1171 Vertical Floor Steamer User Manual
- June 12, 2024
- MARTA
Table of Contents
marta MT-1171 Vertical Floor Steamer
Product Information
The product is a steamer with the model number MT-1171. It is produced by Cosmos Far View International Limited, located at Room 701, 16 apt, Lane 165, Rainbow North Street, Ningbo, China. The power supply for the steamer is 230V ~ 50Hz.
Parts List
- Steamer
- Trousers clips
- Telescopic bar
- Steam hose
- Telescopic bar hole
- Water tank
- Operating light indicator
- Mode switcher
- Main unit
- Brush nozzle
- Thermal insulated glove
Specification
- Model: MT-1171
- Power supply: 230V ~ 50Hz
- Producer: Cosmos Far View International Limited
Warranty Information
The warranty does not cover supplies such as filters, ceramic and non-stick coating, rubber seals, etc. The production date can be found in the serial number on the identification sticker on the gift box and/or on the device. The serial number consists of 13 characters, where the 4th and 5th characters indicate the month and the 6th and 7th characters indicate the year of device production. The producer may change the complete set, appearance, country of manufacture, warranty, and technical characteristics of the model without notice.
Contact Information
For any further inquiries or assistance, you can contact Cosmos Far View
International Limited at:
Address: Room 701, 16 apt, Lane 165, Rainbow North Street,Ningbo, China
Phone: 8(812)325-23-48
Website: http://multimarta.com
Product Usage Instructions
Caution
Before using the steamer for the first time, please read the user manual
carefully and follow the instructions.
Before the First Use
Prior to using the steamer, it is recommended to clean the device from calc
(limescale). This should be done at least once a year or every 50 hours of
using the device.
Cleaning and Maintenance
To clean the device from calc, switch off the device and allow it to cool.
Then, pour water into the watertank and clean the device as per the
instructions provided in the user manual.
Troubleshooting
If you encounter any issues with the steamer, refer to the following
troubleshooting guide:
| Case | Cause | Solution |
|---|---|---|
| No steam | Device is not switched on |
Watertank is empty
Steam hose is folded or deformed
Limescale inside the device| Check connection with outlet
Switch off the device, cool, pour water in watertank
Exclude the fold or deformation of steam hose
Clean the device from calc not less than 1 time a year or every 50
hours of using the device
Weak steam or stream is interrupted| Small volume of water inside the
watertank or watertank is
empty
Steam is not formed yet
Steam hose is folded or placed horizontally| Switch off the device, cool, pour
water in watertank
Pause is needed for the formation of steam
Do not use steam hose in horizontal position or in position lower
than the level of the device
Water flows through the hole steam tip| Accumulation of condensate in the
steam hose| Do not use steam hose in horizontal position. Keep steam hose
vertically until water will not drain into the device.
The device is heated slowly and/or disperses the white
particles| Limescale inside the device| Clean the device from calc not less
than 1 time a year or every
50 hours of using the device
Noise in the steam hose| Accumulation of condensate in the steam hose| Do not
use steam hose in horizontal position. Keep steam hose
vertically until water will not drain into the device.
Please note that the producer reserves the right to change the complete set, appearance, country of manufacture, warranty, and technical characteristics of the model without notice. It is recommended to check these details when purchasing the device.
GBR USER MANUAL
Parts list
- Steamer
- Trousers clips
- Telescopic bar
- Steam hose
- Telescopic bar hole
- Water tank
- Operating light indicator
- Mode switcher
- Main unit
- Brush nozzle
- Thermal insulated glove
CAUTION
Read this manual carefully before using the appliance and save it for future reference.
- Before the first use, check the device specifications and the power supply in your network.
- It is not intended for industrial use.
- For indoor use only. Use only for domestic purposes according to the instruction manual.
- Do not use with damaged cord, plug or other injuries.
- Keep the power cord away from sharp edges and hot surfaces.
- Do not pull the cord. Always take the socket. Do not reel the cord around the device housing.
- Never attempt to frame and repair the appliance by yourself. If you meet problems, please contact the nearest customer service center.
- Using accessories or replacement parts that are not recommended or sold by the manufacturer may cause damage to the appliance.
- Always unplug the appliance and let it cool down before cleaning and removing parts. Keep unplugged when not in use.
- To avoid electric shock and fire, do not immerse in water or other liquids. If this occurs, immediately unplug it and contact service center for inspection.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Check the device before each use to avoid the risk of contact with of hot water that might accumulate on the steam nozzle, keeping it opposite yourself. Use operating device only in vertical position, moving up and down. Never use a steam nozzle horizontally, don’t turn it backwards, it can lead to water leakage and skin burns.
- Never direct the flow of steam towards people or animals. Never use steam flow for clothing worn on people.
- Do not try to disconnect the steam hose during operation , it can be cause of burns.
- The device must not be used for cleaning of electrical devices , such as ovens , electric ovens , kitchen hoods, microwave ovens, TVs , lamps , hair dryers, electric heaters , etc.
- Disconnect the appliance before filling the water tank
- Do not lift or pull the appliance by the steam hose
- Do not add detergents / cleaners in a water tank
BEFORE THE FIRST USE
- Unpack the appliance and remove all packaging materials and labels.
- Wipe the surface with a damp cloth and detergent.
CLEANING AND MAINTENANCE
- Before cleaning, always unplug the appliance.
- Clean the device with a damp cloth, wipe dry.
- Clean the appliance from scale regularly. Use special cleaners that can be purchased at special stores. Applying cleaners, follow the instructions on the packaging.
TROUBLESHOOTING
| Case | Cause | Solution |
|---|---|---|
| Device is not switched on | Check connection with outlet | |
| No steam | Watertank is empty | Switch off the device, cool , pour water in |
watertank
| Steam hose is folded or deformed| Exclude the fold or deformation of steam
hose
|
Limescale inside the device
|
Clean the device from calc not less then 1 time a year or every 50 hours of using the device
|
Small volume of water inside the watertank or watertank is empty
|
Switch off the device, cool , pour water in watertank
Weak steam or stream is interrupted| |
| Steam is not formed yet| Pause is needed for the formation of steam
|
Steam hose is folded or placed horizontally
|
Do not use steam hose in horizontal position or in position lower, than level of device
Water flows through the hole steam tip
|
Accumulation of condensate in the steam hose
|
Do not use steam hose in horizontal position. Keep steam hose vertically until water will not drain into the device.
The device is heated slowly
and / or disperses the white particles
|
Limescale inside the device
|
Clean the device from calc not less then 1 time a year or every 50 hours of using the device
Noise in the steam hose
| Accumulation of condensate in the steam hose|
Do not use steam hose in horizontal position. Keep steam hose vertically until water will not drain into the device.
SPECIFICATION
- Model Power supply
- Producer: Cosmos Far View International Limited
МТ-1171
2
30 V ~ 50 Hz
Room 701, 16 apt, Lane 165, Rainbow North Street , Ningbo, China
Made in China
WARRANTY
WARRANTY DOES NOT COVER SUPPLIES (filters, ceramic and non-stick coating, rubber seals, etc.)
Production date is available in the serial number located on the
identification sticker on the gift box and/or on sticker on the device. The
serial number consists of 13 characters, the 4th and 5th characters indicate
the month, the 6th and 7th indicate the year of device production.
Producer may change the complete set, appearance, country of manufacture,
warranty and technical characteristics of the model without notice. Please
check when purchasing device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>