ENFORCER SD-72231-6MQ Mortise Cylinder Key Switch with LED Instruction Manual
- June 12, 2024
- ENFORCER
Table of Contents
ENFORCER SD-72231-6MQ Mortise Cylinder Key Switch with LED
Product Information
The Mortise Cylinder Key Switches with LED are designed to provide backup access control for electronic locks. These switches can be used to switch between normally closed (N.C.) and normally open (N.O.) contacts, forcing the door to open when a keypad or proximity card reader fails to activate the lock. The switches are available in two models: SD-72231-6MQ and SD-72281-6MQ, both of which have the same appearance.
The key features of the Mortise Cylinder Key Switches with LED include:
- Keyed mortise cylinder with 2 keys included
- Removable mortise cylinder for ease of keying
- Red (standby) and green (triggered) LEDs
- Flush mount design with vandal-resistant security screws
- Chrome-plated aluminum back plate that fits single-gang back box
- Stainless steel front cover that conceals mounting screws
- DPDT switch type with a contact rating of 25A@24VAC
- Color-coded wires for easy wiring
- Maintained output for SD-72231-6MQ model and momentary output for SD-72281-6MQ model
Product Usage Instructions
- Remove the front cover from the unit.
- Thread the cable wire through the electrical box.
- Connect the wires to the switch using the wiring diagram provided.
- Fasten the back plate to the electrical box using the included security screws.
- Finish the assembly by snapping the front cover onto the back plate.
Sample Application:
- Connect an electromagnetic lock to the normally closed (N.C.) side of one of the switch outputs of the SD-72281-6MQ model.
- Connect a strobe light to the normally open (N.O.) side of the other switch output of the SD-72281-6MQ model.
- Activating the switch of the SD-72281-6MQ model will unlock the electromagnetic lock and trigger the strobe light.
Important Note: Ensure that the installation and configuration of this product comply with all national, state, and local laws and codes. SECO-LARM will not be held responsible for any violation of current laws or codes.
Mortise Cylinder Key Switches with LED
Both models are identical in appearance
| Model | Switch Type | Output |
|---|---|---|
| SD-72231-6MQ | DPDT | Maintained |
| SD-72281-6MQ | DPDT | Momentary |
If a keypad or proximity card reader fails to activate an electronic lock, the user can switch between normally closed (N.C.) and normally open (N.O.) contacts using the ENFORCER Single-Gang Mortise Cylinder Key Switches with LED (available with either momentary or maintained outputs), forcing the door to open. This acts as a backup for access control systems, so that the system does not rely on the integrity of a single device.
- Keyed mortise cylinder (2 keys included)
- Mortise cylinder removable for ease of keying
- Red (standby) and green (triggered) LEDs
- Flush mount with vandal-resistant security screws
- Chrome-plated aluminum back plate fits to single-gang back box
- Stainless steel front cover conceals mounting screws
- DPDT, 25A@24VAC contact rating
- Color-coded wires for easy wiring
- Maintained (SD-72231-6MQ) or momentary (SD-72281-6MQ) output
Parts List
- 1x Front cover
- 1x Back plate
- 2x Security screws
- 1x Security wrench
- 2x Keys
- 1x Varistor
- 1x Manual
No replacement keys are available. Please make replacement copies of your keys and store them in a safe place.
Specifications
| Model | SD-72231-6MQ | SD-72281-6MQ |
|---|---|---|
| Switch type | DPDT Switch | |
| LED Indicators | Red (standby) and green (triggered) | |
| Output | Maintained | Momentary |
| Contact switch | 25A@24VAC, NO/NC | |
| Dimensions | 23/4″x41/2″x17/16″ (69x114x37 mm) |
Overview
NOTE : Shown without cover.
Installation
- Remove the front cover from the unit.
- Thread the cable wire through the electrical box.
- Connect the wires to the switch using the wiring diagram below.
- Fasten the back plate to the electrical box using the included security screws.
- Finish assembly by snapping the front cover onto the back plate.
Sample Application
- An electromagnetic lock is connected to the normally closed (N.C.) side of one of the switch outputs of the SD-72281-6MQ.
- A strobe light is connected to normally open (N.O.) side of the other switch output of the SD-72281-6MQ.
- Activating the switch of the SD-72281-6MQ will unlock the electromagnetic lock and trigger the strobe light.
NOTE : The above application is an example of a momentary output. If a maintained output is required, then use the SD-72231-6MQ instead.
Wiring Diagram
IMPORTANT :
Users and installers of this product are responsible for ensuring that the
installation and configuration of this product complies with all national,
state, and local laws and codes. SECO-LARM will not be held responsible for
the use of this product in violation of any current laws or codes.
IMPORTANT WARNING :
Incorrect mounting which leads to exposure to rain or moisture inside the
enclosure could cause a dangerous electric shock, damage the device, and void
the warranty. Users and installers are responsible for ensuring that this
product is properly installed and sealed. California Proposition 65 Warning:
These products may contain chemicals which are known to the State of
California to cause cancer and birth defects or other reproductive harm. For
more information, go to
www.P65Warnings.ca.gov.
WARRANTY :
This SECO-LARM product is warranted against defects in material and
workmanship while used in normal service for one (1) year from the date of
sale to the original customer. SECO-LARM’s obligation is limited to the repair
or replacement of any defective part if the unit is returned, transportation
prepaid, to SECO-LARM. This Warranty is void if damage is caused by or
attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair or alteration, improper or abnormal usage, or faulty installation, or
if for any other reason SECO-LARM determines that such equipment is not
operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive
remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral,
incidental, or consequential personal or property damage of any kind to the
purchaser or anyone else.
NOTICE :
The SECO-LARM policy is one of continual development and improvement. For that
reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints. All trademarks are the
property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright ©
2023 SECO-LARM U.S.A., Inc. All rights reserved.
SECO-LARM ® U.S.A., Inc. 16842 Millikan Avenue, Irvine, CA 92606
- Phone: 949-261-2999 | 800-662-0800
- Website: www.seco-larm.com
- Email: sales@seco-larm.com
MI_SD-722×1-6MQ_230607.docx
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>