SEALEY ASH2000.V2 2 Tonne Capacity High Level Supplementary Stand User Manual
- June 12, 2024
- SEALEY
Table of Contents
2 TONNE CAPACITY HIGH LEVEL
SUPPLEMENTARY STAND
MODEL NO: ASH2000.V2
ASH2000.V2 2 Tonne Capacity High Level Supplementary Stand
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these
instructions, and properly maintained, give you years of trouble free
performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instructions
IMPORTANT NOTE: these stands are rated singly. Used in pairs they will
support twice the rated load.
TAKE CARE; you may know the total weight of the load you want to support but
you cannot calculate the exact weight distribution between support points.
For this reason always allow a 40% margin for error.
For example: a load weighing 4tons could have a single point load of more than
2tons and two 2ton supports would not be adequate.
NOTE: Sold singly but must be used in pairs. Only to be used in
conjunction with permanently fixed lifts. Not mobile column lifts.
SAFETY
WARNING!
DO NOT OVERLOAD SUPPLEMENTARY SUPPORT STANDS BEYOND RATED CAPACITY.
OVERLOADING CAN CAUSE DAMAGE
TO, OR FAILURE OF, THE STANDS. POSITION LOAD ON CENTRE OF CRUTCH/SADDLE ONLY.
ALWAYS ENSURE ADEQUATE
NUMBER OF STANDS ARE USED TO SUPPORT THE LOAD FULLY AND USE ON A HARD LEVEL
SURFACE CAPABLE OF
SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL SURFACES CAN
RESULT IN LOAD INSTABILITY
AND POSSIBLE LOSS OF LOAD. DO NOT USE ON TARMACADAM. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT
IN DAMAGE TO STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE, SERIOUS
PERSONAL INJURY OR LOSS OF LIFE.
▲ DANGER! GREAT CARE MUST BE TAKEN TO ENSURE YOU LOWER THE LOAD
SLOWLY AND CAREFULLY ONTO THE CENTRES OF THE CRUTCH/SADDLE OF THE STANDS.
√Inspect stands before each use. DO NOT use if they show signs of damage. DO
NOT use if it is suspected that they have been overloaded.
√Use only as specified by the manufacturer. √These stands must be used in
pairs and in conjunction with a permanently fixed lift. They are not designed
to support a load on their own.
√Use no more than a single pair of stands either on the front or rear of the
vehicle.
√ Vehicle must have the wheels that stay in contact with the lift chocked
before using the stands.
√ Ensure the load does not exceed the maximum capacity as marked on the stand.
× DO NOT alter or modify the stands in any way.
√Use on a hard, level surface, e.g. concrete. DO NOT use on uneven ground or
tarmacadam.
√ Make sure that each stand is securely located under a strong point on the
load; consult the manufacturer’s handbook for guidance.
√Ensure that height adjust locking mechanism is fully located before applying
any load to the stand.
√Ensure that the load is located centrally on the saddle and that the weight
is directed through the vertical axis of the stand.
√ Ensure that the load and stands are stable before starting work.
√Ensure that it is not possible for the load to move before commencing any
work.
√Before commencing any work undertake a risk assessment.
√Ensure that a responsible person is aware of the work about to be undertaken.
√ Replace any labels on the stand should they become unreadable. This applies
in particular to any warning or operation instruction labels. If replacement
labels are required, contact your Sealey stockist.
× DO NOT use stands on the highway, or anywhere else if it is deemed to be
unsafe.
× DO NOT push or twist the load whilst it is supported on stands.
× DO NOT mix components between stands. Use only as supplied.
× DO NOT allow children or animals in the vicinity of loads supported on
stands.
× DO NOT leave a load on stands in an area that could be considered a hazard
to others or property.
√ Only to be used in conjunction with permanently fixed lifts. Not mobile
column lifts.
× DO NOT use the stand or multiple stands to solely support the vehicle.
INTRODUCTION
All steel stand with pin and chain load support and full width crutches for
safe support of load. Designed to support part of a vehicle that is beingused
on a lift where free access is required. Stands also help prevent the
tipping/rocking of the vehicle.
Note: These stands should not be used to support a vehicle on their own.
Sold as singles, but MUST be used in pairs.
SPECIFICATION
Model No ………………………………………….AS2000HS.V2
Capacity Each……………………………………………..2000Kg
Minimum Height………………………………………….1210mm
Maximum Height…………………………………………1795mm
OPERATION
4.1. Before undertaking work, conduct a risk assessment with a responsible
person and ensure it covers the weight to be supported and a margin for
error. Never work alone on a load supported on these stands. It is the
employer’s responsibility to ensure the operator has read these instructions
and is familiar with the products’ use and limitations. Ensure that all
operators can read English or have the instructions explained to them in
their native language. Also ensure the warnings on the product are observed.
4.2. Vehicle must have wheels that stay in contact with the lift chocked
before using the stands.
4.3. Use only in conjunction with a permanently fixed vehicle lift – Never
with any other jacking device. Elevate the lift to the appropriate height and
locate the supplementary supports, on the recommended support positions.
4.4. Ensure the pin is inserted fully. Use stands as a pair to support either
the front or rear of the vehicle only. BE CERTAIN that all the stands are set
to a height that will leave the load supported completely horizontal and not
at an angle that could cause slipping on the stand support heads. Ensure
there are no objects or individuals in the area other than the operator and
the supervisor. Take extreme care in lifting or lowering the load. Engage the
assistance of a colleague while you perform this task. LOWER ONTO ALL STANDS
BEING USED AT THE SAME TIME, ensuring load is lowered onto the centre of the
crutch/saddle.
‰ WARNING! When load is supported on stands never apply excessive force to
the load so that it becomes unstable.
4.5. To remove stands, lift load slowly, ensuring that the load is balanced
and will not slip from lifting points. Remove the stands.
MAINTENANCE
5.1. Before and after each use, check that stands and stand welds are not
cracked and that there are no missing or damaged parts. Any suspect stands
must be removed from service immediately.
5.2. Periodically lubricate the main support column with general purpose oil.
5.3. After use, wipe the stand and saddles clean.
5.4. Store the stand in a dry childproof area.
Parts support is available for this product. Please email
sales@sealey.co.uk or telephone 01284 757500
ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on
technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty:** Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
ASH2000.V2 Issue 1 01/11/21
Documents / Resources
|
SEALEY ASH2000.V2 2 Tonne Capacity High Level Supplementary
Stand
[pdf] User Manual
ASH2000.V2, ASH2000.V2 2 Tonne Capacity High Level Supplementary Stand, 2
Tonne Capacity High Level Supplementary Stand, Capacity High Level
Supplementary Stand, High Level Supplementary Stand, Supplementary Stand,
Stand
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>