TOYS FACTORY H9 Obstacle Avoidance 8K Brushless Mini Drone User Manual

TOYS FACTORY H9 Obstacle Avoidance 8K Brushless Mini Drone

Product Information

The product has been evaluated and meets the general RF (radio frequency) exposure requirements set by the Federal Communications Commission (FCC). It is designed to be used in portable exposure conditions without any restrictions.

Product Usage Instructions

1. Ensure that the device is fully charged or connected to a power source before use.
2. Power on the device by pressing the designated power button.
3. Follow the device’s user interface or display instructions to navigate through its features and functions.
4. Take note of any specific instructions or warnings provided in the user manual regarding safe usage, maintenance, and handling of the device.
5. When using the device in portable exposure conditions, ensure it is held or placed in a comfortable and secure manner.
6. If any discomfort or unusual sensations occur during use, immediately stop using the device and consult the user manual or contact customer support.
7. Keep the device away from water, extreme temperatures, and direct sunlight to prevent damage.
8. When not in use, store the device in a safe and dry place away from children and pets.
9. Follow local regulations and guidelines regarding the use of electronic devices in specific environments or situations.

Please refer to the complete user manual for detailed instructions, troubleshooting information, and additional safety guidelines.

Safety instructions

1. please keep the parts of drone out of the reach of children.
2. this drone is very powerful. When using it for the first time, you should push the left control lever slowly to prevent the drone from rising too fast and causing unnecessary collisions and injuries.
3. when a flight is ended, please tum off the power switch of remote control first and turn off the power switch of the drone then.
4. do not place the drone battery in high-temperature condition or near flammable or explosive materials.
5. please keep the drone at a distance of 4.5 meters from humans and animals to ensure safety and prevent injury.
6. this drone is suitable for people aged 14 and over, and it should be within the sight of the operator’s (coach) to ensure safe flight.
7. do not charge the battery of the remote control if the battery is a non-rechargeable battery. The drone must be used with the original batteries.
8. if the drone will not be used for a long time, please take the batteries out of the remote control unit.
9. do not cause a short circuit during the charging.
10. if you do not use the drone for more than 10 days, please discharge the battery of drone to 40-50%(Iight for a certain time). In this way, the life of battery will be extended greatly.
11. please keep a safe distance from the rotating propeller to prevent injury.
12. all operators should abide by the electromagnetic environment regulations of China on the aeronautical radio (station), which remote control radios are prohibited from being used within 5000 meters of the airport pavement, they are also required to comply with the certificate and broadcasting regulations made by the relevant regulatory authorities, including flight time and area.
13. please assemble the drone under the supervision of an adult.
14. operators are responsible for their safe flight and safe distance. Do not hover and fly over the crowd (more than 12 people).

Know your drone

Adopt 2.4Ghz Frequency,multi-perso operate at the same time, do not interfere with each other.Through remote control to operated the drone,or WIFI connect drone and mobile phone, APP mode control drone,more playing funtions.

Drone

Description of drone
The aircraft has good controllability and stability, and with the functions of real-time image transmission, information return, mobile phone control, photography and video, gesture recognition, trajectory flight, one-key return and headless mode, etc. Also it is low power alarm tips.

Installing the Propellers

The Drone comes with replaceable propellers if the originals are broken or badly damaged.

1. When installing for the first time, please carefully distinguish the propellers type.
2. Referring to Figure 3, insert the groove of the propeller opener into the bottom of propeller which needs to be replaced. And press the handle of the opener to take down the propeller.
3. Referring to Figure 4, distinguish between type A and type B propellers, and press the propeller vertically to install them on the motor shaft. The mark can be found on the rotor. It is extremely important to use the correct propeller (A or B) for replacement. Using the incorrect propeller will make the drone out of to control.

Battery Charging Steps

The battery is a 3.7V lithium battery, pis using factory-configured USB cable to charge. & First using drone to fly, please fully charge the battery.

Charge way Charging red light, full of lights off, charging time is about 100 minutes

Remote control batteries installation
Open and remove the battery cover, according to the correct polarity putting into the three AA batteries, battery installation direction as shown in the picture, close the cover and screw it. (AA* 3PCS Remote control battery needs to be purchased separately.)

Remote control

Functions Instructions

Preparing for flight

Preparing Inspection
Please inspect the following items before flying

1. Whether the drone and remote control are both with fully battery power
2. Whether the propellers are installed correctly and without any damage
3. Whether the propellers can run normally when the produce is started
4. Check whether the gyroscope completed successfully.
5. Whether successful connect smartphone and have a transmission image
6. Whether the environment suitable for frying

Notes: Please check drone’arms are fully open.

Flight environment requirements

First Using

1 , calibration
Turn on the power switch and place the aircraft on the flat ground with the indicator flashes. And then turn on the power switch of the remote control, and the aircraft will automatically matching the frequency. After, pulling out the two rockers to correct the gyroscope with a sound of Di, a111d the aircraft indicator light is on for a long time, which means that the frequency matching is completed, and the aircraft can be taken off.
Note that the gyroscope needs to be calibrated every time the flight is restarted, and the aircraft needs to be placed horizontally on the ground.

2, One-button take-off and one-button landing
It is suggested that the height of this product is determined by barometer.Due to the influence of various environmental temperatures and other different factors, it is normal for the aircraft to change evenly at the beginning of flight or at low voltage.
It must be operated after 2.4 G alignment is completed

Advanced Flight Function

Speed adjustment
Press the speed switch button on the remote control to switch the flight speed of the aircraft. When switching to the medium speed gear, the remote control deliver two sounds of Di. When switching to the high gear, the remote control will deliver three sounds of Di. Each time the remote control and the aircraft are turned off and restarted, the aircraft gear will automatically return to the low gear.

Headless mode
Press headless mode button.start Headless mode,press again exit this mode.

Camera adjustment
The drone camera up or down adjustment.

Rolling
Press the rolling button and then push the direction control lever to roll the aircraft in different directions.
Warning: rolling function consumes a lot of power and should be reduced. More important, the novice suggests using it in an open space.
PhotoNideo
After turn on the aircraft, press the Photo/Video button to take photos and record video.
Obstacle Avoidance
After turning on the aircraft, press the obstacle avoidance mode button. At this time, if the steering rod is turned in any direction, the obstacle avoidance head of the aircraft will automatically sense whether there is an obstacle in that direction. If there is, the aircraft will not be able to fly in that direction..

Basic operation

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and use d in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instance collation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help important announcement

Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>