TrolMaster TWS-1 Wireless Station User Manual
- June 4, 2024
- TrolMaster
Table of Contents
TrolMaster TWS-1 Wireless Station User Manual
CAUTION
- Read all instructions carefully before installation.
- This product is not intended for use by any persons and children with reduced physical, sensory or mental capabilities or lack of experience and product knowledge.
- The device is designed to be installed INDOORS IN A SPACE THAT IS PROTECTED FROM RAIN AND FLOODING.
- DO NOT clean the exterior of the enclosure with any chemicals that might cause damage. To clean the enclosure… Use a damp cloth only
OVERVIEW
The TWS-1 Wireless Station enables you to use TrolMaster sensors and devices wirelessly with your existing Hydro-X Pro Controller (HCS-2). The TWS-1 is the core of the wireless system, designed to convert wired and wireless protocols, thus building a scalable, solid communication link between the HCS-2 controller, sensors, and devices. The TWS-1 provides a wiring-free option for TrolMaster’s future wireless product development, to enhance user experiences by offering the option to connect sensors and devices wirelessly.
PACKAGE CONTENT
- 1 x TrolMaster Wireless Station (TWS-1)
- 1 x Antenna
- 2 x Phillips Head Screws (0.05in / 1.28mm)
SPECIFICATION
Input Voltage
| 12V, 80mA
---|---
Working Environment|
Temperature: 32°-122°F Humidity: ≤90%
Wireless Standard
| 915Mhz Lora
Product Dimensions|
Unit: 60mm x 82.5mm x 25mm Screw Size: Phillips Head (0.05″ / 1.28mm)
RJ12 cable: 16ft (4.9m) Antenna: 6.99″ (177.5mm)
Product Weight
| 0.42 lbs
Maximum Range (Without Interference)|
1mile / 1.6km
FCC ID
|
2A33F-TWS-1
DIMENSION
HOW TO INSTALL
- The TWS-1 can be mounted directly on any wall surface with appropriate fasteners to secure. (*Do not place TWS-1 inside metal enclosures or else the signal may be affected.)
- Fasten the antenna to the wireless station
- Connect the wireless station to the Hydro-X Pro’s sensor port to connect sensors or the device port to connect device modules wirelessly.
OPERATION INSTRUCTIONS
There is a manual push-button and a LED indicator on the TWS-1 antenna side. The button can be used to pair the wireless station to the controller or to reset the addressing between sensors or device modules and the TWS-1 itself.
| LED Indication | Message |
|---|---|
| No Light | No Powe |
| Flashing Green | Stand By |
| Solid Green | Pairde to Controller |
ADDRESSING INSTRUCTIONS
How to add the TWS-1 to the Hydro-X Pro
-
make sure that your HCS-2 controller is updated to the most recent firmware.
-
Connect the TrolMaster Wireless Station (TWS-1) to the Hydro-X Pro (HCS-2) Sensor port.
-
Press and release the button quickly on the TWS-1 to pair the TWS-1 to the main controller. A “pairing successful” message will appear on the HCS-2 display when successful.
WIRELESS PARING INSTRUCTIONS
-
On the HCS-2 controller screen, go to “Setting” and tab down to the next page. Then go to the “Wireless Station” menu. If the icon does not appear, try pairing again.
-
Press the “Add” button in the top-rigth corner to add a new device.
-
Device(s) will show up on the “Scanning New Device” window with the paring ID provided.
-
Once the device(s) is paired, it will show up in the “Wireless Station” menu.
CAUTION: For instructions on how to pair the specific device/sensor to the TWS-1, please check the manual from the device/sensor unit.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
ISED Canadia Statement
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS-102 and compliance with RSS 102RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
WARNING : DO NOT allow the TrolMaster Wireless Station to be exposed to
water or excessive heat. DO NOT open or attempt to repair or disassemble the
module, as there are no user-serviceable parts inside. Opening the module will
void the warranty.
If the surface of the TrolMaster Wireless Station is dirty, wipe it with a dry
towel. The TrolMaster
Wireless Station operates under natural ventilation conditions.
If you have any questions,please contact us:
TrolMaster Agro Instruments Co.,Ltd. 64 N Mission Dr, Pueblo West, CO 81007
AUG 2022 ©TrolMaster
Room 2520, 25/F., New Tech Plaza, No.34 Tai yau Street,
Kowloon, Hong Kong, China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>