HINKLY 53180 Masthead 14 Tall Bathroom Sconce with Clear Glass Installation Guide
- June 3, 2024
- HINKLY
Table of Contents
GLASS INSTALLATION
Item no: 53180-53182
53180 Masthead 14 Tall Bathroom Sconce with Clear Glass
start here
- Find a clear area in which you can work.
- Unpack fixture and glass from carton.
- Carefully review instructions prior to assembly
DRAWING 1- MOUNTING
-
To begin installation of your fixture it will be first be first necessary to remove the mounting plate (A) from the backplate (B). This is accomplished by first removing the two screws (C), located at the top and bottom of the backplate. Set screws in a safe place for later.
-
Next attach mounting plate (A) to junction box (J) with two screws (D), NOT PROVIDED.
* NOTE:** make sure when installing mounting plate (A) that one of the tabs (T) is facing toward the ceiling and level, before tightening screws (D) – see Drawing 1. -
Make all necessary electrical connections following instruction sheet IS-18 provided.
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUC-TIONS (LS. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
DRAWING 2-GLASS INSTALLATION
-
After all connections are made, tuck wires into junction box (J) and slip backplate (B) over mounting tabs (T) and align threaded holes in tab (T) with holes (H) in backplate (B).
-
Thread in screws (C) removed earlier, and tighten to secure fixture to wall.
1. Slide glass (G) inside of fixture (1)
2. Replace end cap (2)
3. Fixture can now be powered on
DRAWING 3-GLASS INSTALLATION
Drawing 1 – Flush Mount
Drawing 2 – Chain Hun g
Drawing 3 – Post-Mount
I.S. 1 8 wiring grounding instructions
SAFETY WARNI NG: READ WIRING AND GROUNDING INSTRUCTIO NS (IS 18) AND ANY
ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW
WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR
CODE REQUIREMENTS
wiring instructions
Indoor Fixtures
- Connec t positive supply wire (A) (typically black or the smooth, unma rked side of the two-conduc for cord) to positive fixture lead (B) with appropriately sized twist on connec tor – see Dra wings 1 or 2.
- Connec t negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
- Please refer to the grounding instructions below to complete all electrical connec tions
Outdoor Fixtures
- Connec t positive supply wire (A) (typically black or the smooth unma rked side of the two-conduc for cord) to positive fixture lead (B) with appropriately sized twist on connec for — see Drawings 2 or 3.
- Connec t negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
- Cover open end of connec tors with silicone sealant to form a watertight seal. 0 If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backpla te) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
- Please refer to the grounding instructions below to complete all electrical connec tions.
grounding instructions
Flush Mount Fixtures
For positive ground ing in a 3-wire electrical system, fasten the fixture
ground wire (E) (typically copper or green plastic coated) to the fixture moun
ting strap (M) with the ground screw (S) – see Draw in g 1. Note: On straps
for screw supported fixtures, first install the two mounting screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (E) (typicallycoppe r or green plastic coated) under
the head of the ground screw (S) on fixture mounting strap (M) and connec t to
the loose end of the fixture ground wire directly to the ground wire of the
building system with appropriately sized twist-on connec tors – see Draw in g
2.
Post-Mou nt Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to
power supply ground with appropriately sized twist-on connec tor inside post.
Cover open end of connec tor with silicone sealant to form a watertight seal –
see Drawing 3.
HINKLEY 33000 Pin Oak Parkway,
Avon Lake, OH 44012 800.446.5539 / 440.653.5500
hinkley.com