Meta K10 Ball Lock User Manual
- June 12, 2024
- Meta
Table of Contents
K10 Ball Lock
User Manual
Model No:K10
INSTALLATION GUIDE
Prepare Door and Check Dimensions
Install Latch and Strike
STEP 1
Hold the Latch in front of the door hole so that the Latch is flush with the
door edge. Make sure the square-shaped hole is centered. STEP 2
Set the latch backset to 60mm (2.3/8″) or 70mm (2-3/4″) to fit your door hole.
For 70mm (2-3/4″) backset, pull to extend the Latch in order to center square-
shaped hole.
STEP 3
Insert the Latch into the door hole, and tighten Screw A to fix the Latch.
Install Strike Box and Strike Plate with Screw A into the door frame.
In more cases, the existing plate is ready to be used. You can keep the strike plate in box for future use. If not, please make sure the bolt is aligned correctly with the strike plate.
Install Exterior Knob & Interior Knob
Install Exterior Knob
STEP 1
Make sure the door is open.
STEP 2
Make sure the keyhole is under the Exterior Knob
Install Exterior Knob
STEP 3
As shown above, Install the Exterior Knob onto the door with the rod bolts
going through the circular holes on the Latch, and spindle going through the
square-shaped(center)hole.
Install the Interior Knob
STEP 1
Insert the pin into the hole as shown in figure 1 and separate the rosette
from the Interior Knob as shown in figure 2.
STEP 2 The “up”mark above the rosette should face upward. Install the
rosette onto the door with the rod bolts aligning the circular holes, and
spindle aligning the squa re-shaped(center)hole. Then Insert the Screw e into
the circular holes and tighten them to secure the rosette.
Install the Interior Knob
STEP 3
Firstly, make sure the spindle bar is in the vertical position as shown above.
Secondly, rotate the thumb turn to the circular mark. Lastly, insert the
Interior Knob into the rosette by aligning the hole of interior knob with the
spindle bar and aligning the rectangular hole at the edge of the interior knob
with the circular hole at the edge of the rosette.
OPERATION GUIDE
Key To Unlock
• Insert the key into the keyhole at the edge of the Exterior Knob and turn
the key 90″ to unlock, then turn the Exterior Knob to open the door.
Passage Mode
• As shown above, rotate the thumb turn to unlock sign on the right to
activate passage mode. After activating passage mode, the door knob is always
unlocked.
Normal Mode
- As the figure shows, rotate the thumb turn to circular mark above the thumb turn to switch to normal mode. In the normal mode, after unlocking with the fingerprint, the door knob automatically locks in 5 seconds. Both members and administrators can unlock with their fingerprints.
Privacy Mode
- As the figure shows, rotate the thumb turn to lock sign on the left to active privacy mode. In the privacy mode, Both members and administrators can unlock via app.Only the administrator’s fingerprint can unlock.
Restore Factory Setting
- Rotate the thumb turn from the circular mark to the lock sign on the left and then return the thumb turn to the the circular mark, after repeat this operation 5 times, perform the same operation towards the right for 5 times. After that, you will hear the long beep and the fingerprint identification area flashes green.
- Any fingerprints can unlock the lock.
Low Power Indication
- After being unlocked by fingerprint or APP successfully, the buzzer beeps once, and the fingerprint identification area flashes green and then flashes red.
| Action | Buzzer | tirlicatn, |
|---|---|---|
| Power on | Beep once | Inactive |
| Footprint added successfully | Lotif3etr, | Slay green to-a while |
| Un ocking successful | Beeps once | Blinks green once |
| Unlocking failure | Beeps twice | Slinks red once |
| tow batter/ warning | Beeps once (after eV re fingerprint ur app .0 univc 4) |
Blinks green then blinks red latter using fingerprint ex app tc intl.-Irk)
Resetting successful| Long Beep| Blinks green once
APP GUIDE
♦ Account Registration
1.- Tuya Smart App can be downloaded directly by scanning the QR code or
downloaded from App Store(i0S) or Google Play(Android).
http://smart.tuya.com/download
App Unlock /Look
♦ Create Smart Scenes
♦ Member Management and Fingerprints
♦ Setting
♦ Device Information Set Up
SPECIFICATIONS
Technical Parameters
Name| Parameter Description
USB| Type-C/5V2A
Fingerprints max|
20
Low power warning|
4.8V±0.2
Voltage range|
3.4^’4.2V
Stand-by current|
(901.1A
Working current|
–.500mA
Unlock time|
=1.5sec
Working temperature| 23T 131T ( —5t-55t )
♦ FCC WARNING
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device. pursuant to part 15 of the FCC Rules.These
limits are designed to provide reasonable protection against harmful
interference In a residential installation.This equipment generates uses and
can radiate radio frequency energy and,if not installed and used in accordance
with the instructions,may cause harmful interference to radio
communications.However there is no guarantee that interference will not occur
In a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on the user Is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.Operation is subject to the
following two conditions(1)This device may not cause harmful
interference,and(2)this device must accept any interference received,
including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>