YEELIGHT YLDDL-0083-B LED Spotlight User Manual

YEELIGHT YLDDL-0083-B LED Spotlight User Manual

Product Description

• Front view of light body
  

• Reverse view of light body
  

• Base plate
  

Tools

• Self-tapping screw
  

• Expansion tube

Mounting Instructions

1. Take out the spotlight from the package, and remove the base in the opposite direction according to the installation instructions of the base.
   

2. Use an impact drill 6 mm in diameter to make two mounting holes with a length of;, 25 mm in the wall (as shown in the following figure). Put the expansion tube into the mounting hole, and then thread the power cord through the wiring hole. Use self-tapping screws to fix the base on the ceiling, and verify the base is securely mounted.
   

   • In order to avoid any danger, please ask an electrical professional to perform mounting or maintenance.
     Before mounting, make sure to disconnect the power supply to prevent electric shock. Mounting

   • should performed in strict accordance w,th the instructions. Improper mounting is liable to cause accidents such as fall, fire, and electric shock.

3. The wiring hole is suitable for power leads with a cross-sectional area of 1.5-2.5 mm2. Strip the power cord by 11-13 mm, and connect the neutral, live, and ground wires to the ceiling light.
   
   Connect the neutral, and live wires to the wiring holes marked with N, and Lin turn. (Open the internal junction box at the back of the spotlight, connect the wires and tighten the screws with an electrician’s screwdriver.)

   • A solid or stranded hard wire is used as the power lead.

11-13mm

  * This product must be grounded

4. Hold both sides of the lamp with both hands, align the lamp with the fixed base, then push the spotlight slightly to the left or right at the same time(depending on the orientation of the base). When you hear a “click”, the installation is complete.

5. Align the bulb with the GUl0 interface in the spotlight tube, and then rotate it clockwise to complete the installation.After completing the installation, please make sure that the spotlight base is securely installed.

• Always check for proper mounting after you have finished. Improper mounting may cause the product to fa

Specifications

Model: YLDDL-0083, YLDDL-0083-B
Lamp Holder :GUl0
Rated lnput: 220-240V-S0/60Hz
Rated Power: 4.SWeach lampholder
Maximum wattagere placement   bulb: SOW

Model : YLDDL-0084, YLDDL-0084-B
Lamp Holder: GUl0
Rated Input: 220-240V-S0/60Hz S0mA
Rated Power: 4.SWeach lampholder
Maximum wattagere placement bulb: SOW

Model : YLDDL 008S, YLDDL 008S-B
Lamp Holder: GUlO
Rated Input: 220-240V~S0/60Hz
Rated Power: 4.SWeach lampholder
Maximum wattagere placement bulb: SOW

Precautions

• Do not replace the light source of the ceiling light by yourself. The light source should only be replaced by the manufacturer, afer-sales service, or a qualified electrician.
• The light installation requires a qualified electrician, and the wiring must comply with IEEE electrical standards or national standards.
• Make sure the voltage is consistent with the ceiling light’s operating voltage before use. Using the mismatched voltage may damage the ceiling light and cause safety hazards.
• The ceiling light generates heat during working. Please keep it is well ventilated for heat dissipation.
• The ceiling light should be installed in a stable location to prevent it from dropping down or falling off.
• Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user
• For indoor use only.

EU Declaration of Conformity

We Qingdao Yeelink Information Technology Co., Ltd., Hereby, declares that this equipment is in compliance with the applicable Directives and European Norms, and amendments.

WEEE Disposal and Recycling

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/ EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

Manufacturer Qingdao Yeelink Information Technology Co., Ltd Address: 10E-B4, Building B, Qingdao International Innovation Park, No.1 Keyuan Weiyi Road, Laoshan District, Qingdao City, Shandong Province, P.R.China
Website: www.yeelight.com
Customer Service Email: support@yeelight.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>