Huepar 9011G Cross Line or Plumb Spot Combo Laser Level User Manual

June 12, 2024
Huepar

Huepar - logo User Manual
ross Line! Plumb Spot Combo Laser Lovel
9011G/ 9011R, 9211G/9211RHuepar 9011G Cross Line or Plumb Spot Combo
Laser Level - fig

9011G Cross Line or Plumb Spot Combo Laser Level

Thank you for purchasing Hue par Laser Level.
Before using the product, please read this manual thoroughly to ensure proper use.

Huepar 9011G Cross Line or Plumb Spot Combo Laser
Level

Safety Instructions

Before using this product, please read thoroughly and comply with the Safety Instructions and User Manual. Failure to read and follow may void the warranty.

WARNING!
CLASS II LASER PRODUCT
COMPLIES WITH CFR 1040.10 AND 1040.11
Max. Power Output: <ImW
Wavelength: 505nm-660nm
LASER RADIATION:
DO NOT STARE INTO BEAM.
DO NOT DIRECT EYE EXPOSURE.
AVOID VIEW WITH OPTICAL INSTRUMENTS.

ATTENTION:
Read all instructions prior to operating this laser tool. Do not remove any labels from tool.

  • While the product is in operation, be careful not to expose your eyes to the emitting laser beam (Green/Red light source). Exposure to a laser beam for an extended time may be hazardous to your eyes.
  • Do not attempt to view the laser beam through optical tools such as telescopes as serious eye injury may result.
  • Do not disassemble or modify the laser in any way. Modifying the tool may result in hazardous Laser Radiation Exposure.
  • Do not operate the laser around children or allow children to operate the laser. Serious eye injury may result
  •  An exposure to the beam of a Class 2 laser is considered safe for a maximum of 2 seconds. Eyelid reflexes will normally provide adequate protection.
  • The following label/print samples are placed on the product to inform of the laser class for your convenience and safety.

Huepar 9011G Cross Line or Plumb Spot Combo Laser Level -
icon1

User Guide, Maintenance and Care

  • When not in use please power OFF the tool and place the pendulum lock in its locked position.

  • The laser tool is sealed and calibrated at the plant to the accuracy specified

  • It’s recommended to carry out an accuracy check before its first use and periodic checks during future use especially for precise layouts.

  • Do not store the laser tool in direct sunlight or expose it to high temperatures.
    The housing and some integral parts are made of plastics and may become deformed at high temperatures.

  • Exterior plastic parts may be cleaned with a damp cloth.
    Although these parts are solvent resistant, NEVER use solvents. Use a soft, dry cloth to remove moisture from the tool before storage:

  • Store the tool in its case when not in use. If storing for extended time, remove batteries before storage to prevent possible damage.

  • Do opt dispose of this product with household waste.

  • Always dispose of batteries per local code.

  • Please recycle in line with local provisions for the collection and disposal of electrical and electronic waste under the WEEE Directive.

Battery Safety

  • Keep the battery away from children, and pets.
  • Please pay attention to the position of the positive and negative pole.
  • Please use large-capacity rechargeable batteries or alkaline battery above 1500mAh for each when replace batteries.
  • Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type.
  • When the device will not be used for a long time, please remove the batteries and store them in dry condition.

Product Overview

Huepar 9011G Cross Line or Plumb Spot Combo Laser Level -
overview

  1. Vertical Horizontal Laser Window
  2. Pendulum/Transit Lock
  3. Battery Compartment
  4. 1/4°-20 threaded mount
  5. Keypad
  6. 5/8″11 threaded mount

Operation Modes

Turn ON the laser tool:

  • Method 1: Short press the Keypad to turn laser tool ON.
  • Method 2: Slide the pendulum/transit switch to the Unlocked Position to turn laser tool ON

Turn OFF the laser tool:

  • Step 1, Slide the pendulum/transit switch to the Locked Position.
  • Step 2, Short press the Keypad to turn laser tool OFF.
    Note: The laser level can only be turned off when the pendulum/transit in its Locked Position.

Self Leveling Mode

  • is enabled when the pendulum transit is switched to the unlocked position.
  • The laser beam(s) blink fast when tool is out of self-leveling range (4°+1°).
    Note: When using under Self-leveling mode, please place this laser tool on a level surface.

 Manual Tilt Mode

  • is enabled when the pendulum transit is switched to the locked position
  • is enabled to position the laser tool at various angles to project non-level straight lines or points.
  • The laser beam(s) will blink about every 3-5 seconds to notify the user.
    Notice: The laser beam(s) projected in manual mode cannot be used as a horizontal or vertical reference in nature.

 Specifications

Cross Line/Plumb Spot Combo Laser Level

Model 9011G 9011R 9211G 9211R
Laser Beam Green
Beams Red
Beams Green
Beams Red

Beams
Laser Class| Class 2 (IEC/EN60825-1/2014), <1mW
Laser Wavelength| 505-520nm| 635-660nm| 505-520nm| 635-660nm
Leveling Accuracy| +3mm/10m
Horizontal/Vertical Accuracy| ±3mm/10m
Up Dot Accuracy| /| 2mm/10m
Down Dot Accuracy| /| 3mm/10m
Leveling/Compensation Range| 4°±10
Reference Working Distance (Line), 100LUX| 30m| 20m| 25m| 15m
Reference Working Distance (dot), 100LUX| /| /| 60m| 25m
Operating Time (all laser beams on)| 6 Hours| 10 Hours| 6 Hours| 12 Hours
Power Source| 2x”AA’ (LR6)
IP Rating| IP54
Operation Temperature Range| -10°C — +50°C
Storage Temperature Range| -20t — +70°C

Note

  • Appearance and specifications may differ due to product improvement.
  • Working distance varies depending on the operating environment.
  • Battery life depends on battery capacity and quality, it is recommended to use large-capacity rechargeable batteries

Warmly

The laser tool passed rigorous and comprehensive product inspection. We are confident of the quality of our products and offer outstanding guarantee for professional users of the products.
We offer One Year Limited Warranty from date of purchasing provided that:

  • Proof of purchase
  • Fair wear and tear
  • Have not repaired by unauthorized persons
  • Has not been misused

Defective products will be repaired or replaced, free of charge or at our discretion, if sent together with proof of purchase to our authorized distributor(s)
This Warranty does not cover:

  • Faults caused by accidental damage
  • Failure to use according to manufacturers’ instructions
  • Defects caused by maintenance or renovation without our authorization
  • Calibration and care are not covered by warranty

Note:

  • To the extent permitted by law, we shall not be liable under this Warranty for indirect or consequential loss resulting from faults in this product.
  • Repair or replacement under this Warranty does not affect the expiry date of the Warranty.
  • This warranty is limited to purchased customers, and is not permitted to transfer this warranty to other third parties.
  • This Warranty may not be varied without our authorization.

http://eepurl.com/cVG6yT

Please scan the QR code to register this  product and enjoy 2-year warranty.


If you encounter any question or confusion about the product, please feel free to  contact us: [support@huepar.com](mailto:support@huepar.com)


![Huepar - logo](https://manuals.plus/wp-content/uploads/2023/07/Huepar-logo-1.png)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals