Huepar P02CG 360 Degree Self-Leveling Cross Line Laser Level User Manual

Huepar P02CG 360 Degree Self-Leveling Cross Line Laser Level

Accessories Description

1. Li-ion Battery
2. Power Adapter& Type-C Power Cord
3. Laser Target Plate
4. Remote Control
5. Wall steel sheet
6. Multifunctional Bracket
7. Hard Carrying Case
8. Laser Level Adapter
9. Soft Carrying Bag
10. Lifting Base
11. Laser Enhancement Glasses GL0lG/GL0lR
12. Laser Detector LR-SRG or LR-6RG
13. Laser Level Rotating Base AT2
14. Laser Telescopic Pole LP36
15. 1.4m Tripod TPD14
16. 1.6m Tripod TPD16
17. 1.65m Aluminum Flat Head Contractor Tripod M3Y
18. Sm Telescopic Grade Rod Leveling Staff GRS

Thank you for purchasing Huepar 360° Self-leveling Cross Line Laser Level. Before using the product, please read this manual thoroughly to ensure proper use.

Product Overview

1. Top / Bottom Laser Line Switch
2. Side Laser Line Switch
3. Front Laser Line Switch
4. Pulse Mode Button
5. Power Indicator
6. Pendulum/ Transit Lock
7. Type – C Charging Port
8. Top Laser Window
9. Front Laser Window
10. Side Laser Window
11. Bottom Laser Window(P04CG/P03DG)
12. Battery
13. Battery Unlock Button Buckle
14. 1/4″-20 Threaded Mount
15. 5/8″-11 Threaded Mount (P02CG/P03CG)

Safety Instructions

Please read thoroughly and comply with the Safety Instructions and User Manual before using this product. Failure to read and follow may void the warranty.

WARNING! CLASS II LASER PRODUCT COMPLIES WITH 21 CFR 1040.10 AND 1040.11 Max. Power Output: <lmW

Wavelength: 505nm-660nm

LASER RADIATION:
DO NOT STARE INTO BEAM. DO NOT DIRECT EVE EXPOSURE. ACOIDVIEW WITH OPTICAL INSTRUMENTS.

ATTENTION:
Read all instructions prior to operating this laser tool. Do not remove any labels from tool.

• While the product is in operation, be careful not to expose your eyes to the emitting laser beam (Green light source). Exposure to a laser beam for an extended time may be hazardous to your eyes.
• Do not attempt to view the laser beam through optical tools such as telescopes as serious eye injury may result.
• Do not disassemble or modify the laser in any way. Modifying the tool may result in hazardous Laser Radiation Exposure.
• Do not operate the laser around children or allow children to operate the laser. Serious eye injury may result.
• Exposure to the beam of a Class 2 laser is considered safe for a maximum of 2 seconds. Eyelid reflexes will normally provide adequate protection.
• The following label/print samples are placed on the product to inform of the laser class for your convenience and safety.

User Guide, Maintenance, and Care

• When not in use please power OFF the tool and place the pendulum lock in the OFF position.
• The laser tool is sealed and calibrated at the plant to the accuracy specified.
• It’s recommended to carry out an accuracy check before its first use and periodic checks during future use, especially for precise layouts.
• Do not touch the glass window in case of leaving any fingerprints on the window, which may affect the performance of the laser.
• Do not store the laser tool in direct sunlight or expose it to high temperatures. The housing and some internal parts are made of plastics and may become deformed at high temperatures.
• Exterior plastic parts may be cleaned with a damp cloth, NEVER use solvents. Use a soft, dry cloth to remove moisture from the tool before storage.
• Store the tool in its case when not in use. If storing for an extended time, remove batteries before storage to prevent possible damage.
• Do not dispose of this product with household waste.
• Always dispose of batteries per local code.
• Please recycle in line with local provisions for the collection and disposal of electrical and electronic waste under the WEEE Directive.

Charging and Battery Safety

Please read thoroughly and comply with battery safety instructions and attention before charging. Failure to read and follow may result in personal injury, fire, and property damages if the battery is charged and/or used improperly.

Battery Installation:
Push the battery into the groove at the end of the laser tool. When disassembling, press the battery unlock button buckle(13) and pull out the battery.

Charging:
Method 1: Charging when battery is installed into the laser tool Connect the Type-C Charging Port(7) on the laser level to the power supply, the Power indicator (5) will blink, indicating that the battery is being charged. When charging is completed, all four panels of the Power lndicator(5) are on.

Method 2: Charging the battery independently
There is a type-C charging port on the battery. When charging, the power indicator on the battery will light up in red. When charging is completed, the power indicator will turn green.

Note

• When connecting the power supply, the laser tool can work properly without a battery.
• When the battery is less than 15%, the Power indicator (5) will blink every second, indicating that the battery is low.

Attention

• DO NOT SHORT CIRCUIT. Short circuits may cause fire, and injury!
• Do not charge unattended.
• Do not disassemble, or modify the battery.
• Keep the battery away from children, and pets.
• Immediately discontinue use of the battery if the battery becomes abnormal/ deformed (emits an unusual smell, feels hot, changes color or shape, or appears abnormal in any other way). Please contact the manufacturer to replace it.
• Never charge or store the batteries inside your car. Extreme temperatures (low or high) might ignite the battery, and cause a fire.
• Do not place the battery in high-pressure containers, microwave ovens, or on induction cookware.
• Do not carry, or store the batteries together with hairpins, necklaces, or other metal objects.
• On (battery electrolytes) exposure to skin, flush with water immediately. If eye exposure occurs, flush with water for 15 minutes, and seek emergency care immediately.

Operation

Turn ON the laser tool:
A. Method 1: Turn ON the Manual/ Tilt Mode:

• Slide the pendulum to the Locked Position to turn ON the laser tool, the manual mode is activated by default.
• Under manual mode, users can position the laser tool at various angles.

Note

• Please notice the laser beam(s) projected in manual mode cannot be used as a horizontal or vertical reference in nature.

Method 2: Turn ON the Self-leveling Mode

• Slide the pendulum to the ON position to turn ON the laser tool, the self-leveling mode is activated by default.
• When the laser tool is within the self-leveling range( 3°), the laser tool is self-leveling. The laser beam(s) blink fast and the laser tool will beep as well when the tool is out of self-leveling range ( 3°).

Turn OFF the laser tool:
Slide the pendulum to the OFF position to turn OFF the laser tool.

Automatic Power OFF:

• In Manual Mode, when all laser lines are switched OFF, the laser tool will Automatically Turn OFF after about 5 minutes of inactivity.

Note

• If all laser lines are switched OFF while the laser tool is still powered ON, the laser tool will beep and the laser beam(s) will blink fast every 30 seconds to remind the laser tool that it is not turned OFF.

Lines Switching: After powering on, all laser beams will be on by default.

• Short press Top/ Bottom Laser Line Switch(!) to switch the top (8) and bottom (11) horizontal laser lines.
• Short press the Side Laser Line Switch(2) to switch the vertical line of the Side Laser Window(lO). This function is invalid for the P02 model.
• Short press Front Laser Line Switch(3) to switch the vertical line of the Front LaserWindow(9).

Pulse Mode {Use with Laser Receiver):

• With the pulse mode on, the laser tool can work with the laser receiver for working in a brighter environment or a larger working distance.
• When working with the laser receiver, please turn on the pulse mode in advance.
• Switch to Pulse Mode: Turn on the laser tool, short press the Pulse Mode Button(4) to switch to Pulse Mode. The laser beams are dimmer in pulse mode.
• Return Back to Normal Mode: Short press the Pulse Mode Button(4) again to return to Normal Mode. The laser beams will be recovered.

Note

• When switching between Pulse Mode and Normal mode, the laser beam(s) will blink fast as a reminder.
• The Pulse Mode Button(4) will light up in blue when switching to Pulse Mode, and light off when return back to Normal Mode.

Horizontal Laser Beams Accuracy Check
It is recommended to slide the pendulum to the unlocked position to enable the self-leveling mode before the accuracy check. Please ensure that there is no vibration. Accuracy check requires a wall of 10 meters, which needs to be smooth and flat to facilitate marking.

1. Place the laser tool at one end of the wall about 50cm away from the wall and turn on the laser tool. Mark the intersection of the horizontal laser beam and vertical laser beam as mark 1 on the wall.
2. Remain the laser tool in place. Mark the position of the horizontal beam on the wall along the other end of the horizontal laser beam 10 meters away as mark 2.
3. Move the machine parallel to mark 2 along the wall and keep the machine about 50cm away from the wall. Make the intersection of the horizontal laser beam and vertical laser beam precisely align with mark 2 (An adjustable platform is recommended).
4. Mark the horizontal laser beam at the position of mark 1 again along the horizontal laser line as mark 3.
5. Measure the offset of mark 1 and mark 3 on the wall. The offset value should be less than 6mm.
6. If the offset value is more than 6mm, the laser tool should be returned to the service center for repair.

Vertical Laser Beams Accuracy Check

1. Place the laser tool on the floor and turn on the vertical beams of the front laser window and side laser window.
2. Mark the cross point below the laser tool as mark 1 and remain the laser tool in the same position. Mark a mark 2 on the floor Sm away from mark 1, mark the cross point on the ceiling as mark 3.
3. Rotate the level horizontally by 180°, and then move the laser tool close to mark 2, so that the vertical laser line is aligned through mark 2 and mark 1.
4. Mark the laser line at the position of mark 3 on the ceiling as mark 4.
5. Measure the offset of mark 3 and mark 4 on the ceiling. If the measured value is more than the value in the table below, the laser tool should be returned to the service center for repair.

Orthogonal check

1. Install the laser tool on the equipped bracket, and then place it on the flat ground, and turn on the side vertical laser beam.
2. Mark a mark 1 below the laser tool on the floor, and then mark a mark 2 on the floor Sm away from mark 1, and finally mark a mark 3 on the floor Sm away from mark 2.
3. Turn on the vertical laser beams of front laser window and side laser window, and move the laser tool to mark 2. Align the cross point at the bottom of the laser tool to mark 2 accurately, and align the laser beam of the side laser window with mark 3.
4. Mark a mark 4 Sm away, along the vertical line of the front window of the laser tool.
5. Rotate the level horizontally by 90°. Align the cross point at the bottom of the laser tool to mark 2 accurately, and align the laser beam of the side laser window with mark 4.
6. Mark the vertical laser beam of the front window as mark 5 at the position of mark 1.
7. Measure the offset of mark 1 and mark 5. The offset value should be less than 4.5mm. If the offset value is more than 4.5mm, the laser tool should be returned to the service center for repair.

Bluetooth APP/APK

Function

|  |  |  |

Different models have different Bluetooth and function choices. Please confirm the model you purchased according to the label on the laser tool. If you have any questions, please contact the dealer.

Note: The laser tool can connect two Bluetooth devices simultaneously. It can connect two remote controls, or two mobile phones, or one remote control and one mobile phone at the same time.

Remote Control (Optional)

Overview

1. ON/ OFF Button
2. Brightness Adjustment Button (for Upgraded version, not for this version)
3. Switch Horizontal Line(s)
4. Switch Vertical Lines
5. Pulse Mode Button
6. Function Button for Future Upgraded version (not for this version)
7. Function Button for Future Upgraded version (not for this version)
8. Type-C Charging Port

Turn ON/ OFF & Connect

• Press and hold for 2 seconds to turn ON the remote control.
• Turn on the remote control when the laser tool is on, the remote control will match and connect with the laser tool automatically.
• Press  and hold for  2 seconds to turn OFF the remote control.

Note

• If the connection fails, please turn off the remote control and laser tool, then restart them to restore the connection.
• The laser tool is able to connect two Bluetooth remote controls at the same time.
• Please understand that due to the pendulum locking design, the laser tool cannot be turned on or off by the remote control. The self-leveling and manual mode cannot be switched via the remote control.

Function Operation

Lines Switching:

• Short press H to switch the horizontal line(s).
• Short press V to switch the vertical lines.

Pulse Mode:

• Short press to switch to Pulse Mode and return back to normal mode.

Switch OFF the laser lines:

If the laser tool is in Self-leveling Mode:
Short press to temporarily switch off all the laser lines, the laser tool is not turned OFF. Short press any button on the remote control to wake up the laser tool for working again.

If the laser tool is in Manual Mode:
Short press to switch off all the laser lines, the laser tool will Automatically Turn OFF after about 5 minutes of inactivity. Within 5 minutes, users can short press any button on the remote control to wake up the laser tool for working again.

Note: The laser level can only be turned off when the pendulum in its Locked Position.

Indicator on Remote Control

Connect and Match:

• During the connecting and matching the Bluetooth remote control with the laser tool, the indicator will flash in green per second.
• Once connected, the indicator will light up in green continuously.
• If the connection fails after more than 1 minute, the remote control will automatically turn off, and the indicator will light off.

Operation

• After the remote control connected successfully, when pressing any button, the indicator will flash once in green every time you press it.
• When the remote control is not operated within 5 minutes, the indicator will flash in green every 5 seconds, and the remote control enters low power consumption mode. Press any button to resume normal operation.

Battery and Charging

• When the power is low, the indicator will flash in red twice per second. The remote control can still work until the power is exhausted and turn off automatically, and the indicator will light off.
• During charging, the indicator will flash in red.
• When charging is complete, the indicator will light up in green continuously.

Huepar Bluetooth APP/APK(Optional)

Connect the laser tool to Bluetooth APP/APK

• Step 1: Download Huepar APP/APK
  • Method 1: Scan the QR code
  • Method 2: Search “Huepar” in iPhone App Store or Google Play
  • Method 3: Click the link:
• http://xwayserver.pairlink.com.cn/79813391439
• Step 2: Turn on Bluetooth on your phone
• Step 3: Power on the laser tool
• Step 4: Open Huepar APP/APK software
• Step 5: Complete the Bluetooth match and connection with the laser tool
  • lf the connection fails, please exit the APP/APK software and restart the APP/ APK software to restore the connection.
  • The laser tool can connect two phones at the same time, whether on Android or iOS.
• Step 6: Click “PSeries” to enter the operation interface

Function Introduction

1. Smart Pendulum Lock Status: The unlocked or locked icon indicates the status of the pendulum.
2. Bluetooth Connection Status
3. Laser Tool Status Reminder: Under self-leveling mode, icon (3) will be displayed as reminder if the tool is beyond self-leveling range.
4. Click the icon once to switch ON / OFF all laser lines in one click:
   • , In Self-leveling Mode, when click the icon , all laser lines will be switched OFF temporarily while the laser tool remains powered on. When moving the laser tool, the laser beam(s) will blink fast to remind you the laser tool has not been powered off.
   • In Manual Mode, when all laser lines is switched OFF by clicking the icon the laser tool will Automatically Turn OFF after about 5 minutes of inactivity. Click the icon  within 5 minutes again will reactivate the laser tool.
   • To turn off or store the laser tool, please be sure to slide the pendulum into the locked position.
5. Battery Status: When the Li-ion battery is installed, icon will be displayed. When AA battries installed, icon will be displayed. When no battery installed, icon will be displayed.
6. The composition of laser lines
7. Bubble Level
8. Different compositions of different laser lines
9. Switch ON/OFF the pulse mode

Note

• Do not use the laser tool with Bluetooth in the vicinity of gas stations, chemical plants, areas where there is danger of explosion and areas subject to blasting.
• Please read thoroughly and comply with the Safety Instructions and User Manual of the laser tool.
• Do not use the laser level with Bluetooth in airplanes. Do not use the laser level with Bluetooth in the vicinity of medical devices (eg., cardiac pacemakers, hearing aids). This may cause interference.
• The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Huepar is under license.

Specifications

4om/ 130ft

Power Source| Li-ion Battery 11.1V(12.6V Max) 2600mAh
Reference Operating Time (with 11.lV/ 2600mAh Li-ion Battery)| P02:About 11 hrs

P03:About 9 hrs

P04:About 7 hrs

Charging Time| About 3.5 hrs
Mount Size| 1/4″-20 & 5/8″-ll
IP Rating| IP54
Stick a Wall Distance| 13mm
Work Temperature| -10°C~ +50°C
Storage Temperature Range| -20°C~ +70°C

note

• Appearance and specifications may differ due to product improvement.
• Working distance varies depending on the operating environment.
• Keep the pulse mode on when using with receiver for longer working range.

Warranty

The laser tool passed a rigorous and comprehensive product inspection. We are confident in the quality of our products and provide excellent guarantees for professional users of the products.

We offer One Vear Warranty from date of purchase including that:

• Proof of purchase is produced.
• Service/repairs have not been attempted by unauthorized persons
• The product has not been misused Defective products will be repaired or replaced, free of charge or at our discretion if sent together with proof of purchase to our authorized distributor(s)

This Warranty does not cover:

• Faults caused by accidental damage
• The product has suffered unreasonable wear and tear.
• Failure to use according to manufacturers’ instructions
• Defects caused by maintenance or renovation without our authorization
• Calibration and maintenance are not included in the warranty.

Note

• We are not liable for any direct or indirect loss caused by the failure of this product beyond the scope stipulated by law.
• Repair or replacement under this Warranty does not affect the expiry date of the Warranty.
• This warranty is only applied to customers who have purchased this product and is not permitted to transfer this warranty to any third parties.
• This Warranty shall not be altered without our authorization.

You can enjoy a 12 months limited warranty but it can be up to 24 months if you register as a member through the product registration. Please scan the QR code to activate your priority.

If you encounter any questions or confusion about the product, please feel free to contact us: at support@huepar.com

Changzhou Levelsure Optoelectronics Technology Co.,Ltd. E-mail: support@huepar.com Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>