HQ POWER VDSSM5 Sound Mach V Portable DJ Set User Manual

HQ POWER VDSSM5 Sound Mach V Portable DJ Set

Product Information

• Product   Name: VDSSM5
  Model Number: VDSSM5
  User Manual: Available

Features:

• Built-in digital effect generator with 16 pre-selectable effects
• Built-in MP3 player with remote control and Bluetooth input
• Rated output power: 2 x 75 W / 4 ohm

Product Usage Instructions

Safety Instructions

• Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
• Always disconnect mains power when the device is not in use or when servicing or maintenance activities are performed. Handle the power cord by the plug only.
• Indoor use only. Keep this device away from rain, moisture, splashing, and dripping liquids. Never put objects filled with liquids on top of or close to the device.
• Keep this device away from children and unauthorized users.
• Caution: device heats up during use.
• There are no user-serviceable parts inside the device. Refer to an authorized dealer for service and/or spare parts.
• This device falls under protection class I. It is therefore essential to connect the device to a grounded power outlet. Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual. Do not crimp the power cord and protect it against damage. Have an authorized dealer replace it if necessary. Do not use the device if damage to housing or cables is noticed.

Installation

1. Open all four catches [C] (two on the front, two on the back) and take the speakers [A] off the mixing console [B].
2. Unfold the speaker stands [G] and place them on a level and sturdy surface. Mount the speakers on the stands.

Connecting/Disconnecting Audio Devices During a Presentation

If you need to connect an extra audio device during a presentation:

1. Set the volume control of the applicable input channel to zero.
2. Connect the audio device to the input channel.
3. Switch on the audio device.
4. Slowly increase the volume to the desired level.

Taking Down

1. Set all volume controls on the control panel [5,24] to zero.
2. Switch off all audio devices.
3. Switch off [27] the mixing console.
4. Disconnect all audio devices and speakers.
5. Store the microphone and cables in the storage compartments [D].
6. Take the speakers off the stands and fold the stands.
7. Place the folded stands in the mixing console and fix them in place using the straps [E].
8. Place the speakers on top of the mixing console and close the four catches [C].

Caution: Do not force. If the catches do not close properly, then carefully reposition the speakers and try again.

Overview

Refer to the illustrations on page 2 of this manual.

Input channel 5:

• REVERB: apply a reverb effect to this input channel.
• GAIN: set the channel volume. It determines the proportion of this channel in the mix.

Input source selector:

• LINE: select input from the TAPE INPUT jacks.
• MP3: select MP3 input from a USB device or SD card.
• BLT: select input from a Bluetooth device.

Introduction

• To all residents of the European Union
• Important environmental information about this product
• This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.
• If in doubt, contact your local waste disposal authorities.
• Thank you for choosing HQPower™! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don’t install or use it and contact your dealer.

Safety Instructions

| Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
---|---
****| Always disconnect mains power when device not in use or when servicing or maintenance activities are performed. Handle the power cord by the plug only.

| Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids. Never put objects filled with liquids on top of or close to the device.
| Keep this device away from children and unauthorized users.
| Caution: device heats up during use.
****| There are no user-serviceable parts inside the device. Refer to an authorized dealer for service and/or spare parts.

• This device falls under protection class I. It is therefore essential to connect the device to a grounded power outlet.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
• Do not use the device if damage to housing or cables is noticed.

General Guidelines

• Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

| Keep this device away from dust and extreme temperatures. Make sure the ventilation openings are clear at all times. For sufficient air circulation, leave at least 1″ (± 2.5 cm) in front of the openings.
---|---
| Protect this device from shocks and abuse. Avoid brute force when operating the device.

• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified people. Any damage that may occur will most probably be due to unprofessional use of the device.
• All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, crash, etc. Using the device in an unauthorised way will void the warranty.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
• Mechanical wear and LEDs are not covered by warranty.
• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device against damage by leaving it switched off until it has reached room temperature.
• The device shall only be used indoors with an alternating current of max. 230 VAC 50 Hz.
• Keep this manual for future reference.

Features

• ideal portable system for seminars, conferences, presentations, tradeshows, fashion shows, solo entertainers, weddings, sales booths, aerobics, etc.
• 4 wheels for easy transportation
• 150 W system with 5-channel mixer and 5-band equalizer
• 2 detachable full range speakers, each with 10″ woofer, 1″ tweeter, and flange for speaker stands 2 speaker stands are included, fitting into the case
• incl. 1 dynamic microphone with cable
• integrated MP3 player with USB port and SD card reader
• all cables included:
• 2 speaker cables
• 1 power cable
• 1 XLR microphone cable mixer:
• 4 mono input channels for MIC/LINE
• 1 stereo MIC/LINE input and 1 stereo tape/MP3/Bluetooth input
•  with left and right master fader
• 2-band equalizer for each input channel
• 5-band equalizer for main output
• tape in- and output (via RCA connector) allows for connecting to a tape/CD player without using a main input channel
• built-in digital effect generator with 16 pre-selectable effects
• built-in MP3 player with remote control and Bluetooth input
• rated output power: 2 x 75 W / 4 ohm.

Installation

Setting Up

1. Open all four catches [C] (two on the front, two on the back) and take the speakers [A] off the mixing console [B].
2. Unfold the speaker stands [G] and place them on a level and sturdy surface. Mount the speakers on the speaker stands. Or, if you are not using the speaker stands, place the speakers on a level and sturdy surface.
3. Place the mixing console on a table (not incl.) and connect the speakers to the rear panel [F,29] using the included speaker cables.
   • Caution: Always switch the device off before you connect speakers.
4. Set all volume controls on the control panel [H,5,24] to zero.
5. Connect audio devices, such as a microphone (incl.) or an MP3 player (not incl.) to the mixing console as necessary. Refer to Overview for more information on inputs and outputs.
6. Plug the power cord into the power cord connector [28] and plug it into a suitable mains outlet.
7. Make sure the ventilation openings [30] in the rear panel are clear. Remove any objects (spare cables, etc.) that may block them.
   • Note: Store spare cables or other parts in the storage compartments [D].
8. Switch on [27] the mixing console first.
9. Switch on the connected audio devices.
10. Slowly increase the volume of the connected channels to the desired level.

Connecting/Disconnecting Audio Devices During a Presentation

If you need to connect an extra audio device during a presentation:

1. Set the volume control of the applicable input channel to zero.
2. Connect the audio device to the input channel.
3. Switch on the audio device.
4. Slowly increase the volume to the desired level.

Taking Down

1. Set all volume controls on the control panel [5,24] to zero.

2. Switch off all audio devices.

3. Switch off [27] the mixing console.

4. Disconnect all audio devices and speakers.

5. Store the microphone and cables in the storage compartments [D].

6. Take the speakers off the stands and fold the stands.

7. Place the folded stands in the mixing console and fix them in place using the straps [E].

8. Place the speakers on top of the mixing console and close the four catches [C].

Caution: Do not force. If the catches do not close properly, then carefully reposition the speakers and try again.

Overview

Refer to the illustrations on page 2 of this manual.

Input channels 1–4

1| MIC and LINE inputs.

MIC: microphone input, XLR jack. Connect a low impedance microphone. LINE: line input, 1/4″ jack.

For channels 1–3: mono input.

For channel 4: use connector LEFT/MONO for mono input, or use both LEFT and RIGHT connectors for stereo input.

Note : use either the MIC or LINE input. Do not use both inputs at the same time.

2| REVERB: apply a reverb effect to this input channel.
3| TREBLE: adjust the high tones. ± 15 dB at 12 kHz.
4| BASS: adjust the low tones. ± 15 dB at 80 Hz.
5| GAIN: set the channel volume. It determines the proportion of this channel in the mix.
Input channel 5
6| Input source selector:

LINE: select input from the TAPE INPUT jacks.

MP3: select MP3 input from a USB device or SD card     BLT: select input from a Bluetooth device.

7|     TAPE INPUT: connect an input device such as a cassette deck or CD player to the RCA jacks. The input can be added to the mix.

TAPE OUTPUT: connect an output device such as a cassette deck or home audio system to the RCA jacks.

MP3 player with LCD and remote control
8| LCD
9| USB port: insert a USB storage medium.
10| FOL–: press to select the previous folder on the USB device or SD card.
11| FOL+: press to select the next folder on the USB device or SD card.
12| MODE: press repeatedly to select the desired play mode: USB/SD or FM radio.
13| REPEAT: to set up repeat mode.
14| PLAY/PAUSE: use the play/pause button to switch between playback mode and pause mode.
15| EQ: press repeatedly to select the desired equalizer mode: CLASSICAL, BASS, LIVE, ROCK, or POP.
16| VOL–: press to select the previous track. Press and hold to decrease the volume.
17| VOL+: Press to select the next track. Press and hold to increase the volume.
18| Mute key: mutes the volume of the SD/USB player.
19| U/SD – SCAN:

In USB/SD mode: press to switch between the USB device and the SD card.     In FM radio mode: press for automatic channel searching.

---|---
20| Receiver for remote control
21| SD card slot: insert an SD card.
Master output control
22| 5-band equalizer for master output
23| When the device is switched on, the power LED lights.

The level indicator LEDs show the level of the master output.

24| The MASTER L and R sliders control the output level of the left and right signals that are sent to the speakers.
25| REVERB VOL: to adjust the reverb effect level for the master output.
26| PROGRAM: turn the knob to select one of the built-in sound effects.
Rear panel
27| Power switch: turn the device on or off.
28| Power cord connector and fuse holder
29| Outputs to speakers

Cleaning and Maintenance

• All screws shall be tightened and free of corrosion.
• The housing, visible parts, mounting supports and the installation location (e.g. ceiling, suspension, trussing) shall not be deformed, modified or tampered with; e.g. do not drill extra holes in mounting supports, do not change the location of the connections…
• Mechanically moving parts must not show any signs of wear and tear.
• The electric power supply cables must not show any damage. Have a qualified technician maintain the device.
• Disconnect the device from the mains prior to maintenance activities. Let the device cool down.
• Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
• There are no user-serviceable parts, apart from the fuse. Contact your dealer for spare parts if necessary.

Replacing the Fuse

• Only replace the fuse by a fuse of the same type and rating.

1. Before replacing the fuse, unplug the mains lead.
2. Wedge the fuse holder out of its housing with a flat-head screwdriver.
3. Remove the damaged fuse from its holder and replace with the exact same type of fuse.
4. Insert the fuse holder back in its place and reconnect power.

Technical Specifications

dBu at 600 ohm -6/+3 dB
40 Hz – 18 kHz, power amp output 1 W at 8 ohm -6/+3 dB
speakers| woofer| 10″ magnet, 8 ohm, 850 g / 30 oz, 38.6 mm VC
tweeter| 1″
dimensions| 700 x 400 x 590 mm
---|---
weight| 28 kg

• Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device.
• For more info concerning this product and the latest version of this manual, please visit our website www.hqpower.eu.
• The information in this manual is subject to change without prior notice.

© COPYRIGHT NOTICE

• The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder.

Velleman® Service and Quality Warranty

• Since its foundation in 1972, Velleman® acquired extensive experience in the electronics world and currently distributes its products in over 85 countries. All our products fulfil strict quality requirements and legal stipulations in the EU. In order to ensure the quality, our products regularly go through an extra quality check, both by an internal quality department and by specialized external organisations. If, all precautionary measures notwithstanding, problems should occur, please make appeal to our warranty (see guarantee conditions).

General Warranty Conditions Concerning Consumer Products (for EU):

• All consumer products are subject to a 24-month warranty on production flaws and defective material as from the original date of purchase.
• Velleman® can decide to replace an article with an equivalent article, or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible, or if the expenses are out of proportion.
• You will be delivered a replacing article or a refund at the value of 100% of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery, or a replacing article at 50% of the purchase price or a refund at the value of 50% of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery.

Not covered by warranty:

• all direct or indirect damage caused after delivery to the article (e.g. by oxidation, shocks, falls, dust, dirt, humidity…), and by the article, as well as its contents (e.g. data loss), compensation for loss of profits;

• consumable goods, parts or accessories that are subject to an aging process during normal use, such as batteries (rechargeable, non-rechargeable, built-in or replaceable), lamps, rubber parts, drive belts… (unlimited list);

• flaws resulting from fire, water damage, lightning, accident, natural disaster, etc.…;

• flaws caused deliberately, negligently or resulting from improper handling, negligent maintenance, abusive use or use contrary to the manufacturer’s instructions;

• damage caused by a commercial, professional or collective use of the article (the warranty validity will be reduced to six (6) months when the article is used professionally);

• damage resulting from an inappropriate packing and shipping of the article;

• all damage caused by modification, repair or alteration performed by a third party without written permission by Velleman®.

• Articles to be repaired must be delivered to your Velleman® dealer, solidly packed (preferably in the original packaging), and be completed with the original receipt of purchase and a clear flaw description.
  Hint: In order to save on cost and time, please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair. Note that returning a non-defective article can also involve handling costs.

• Repairs occurring after warranty expiration are subject to shipping costs.

• The above conditions are without prejudice to all commercial warranties.

• The above enumeration is subject to modification according to the article (see article’s manual).

• Made in PRC

• Imported by Velleman nv

• Legen Heirweg 33, 9890 Gavere, Belgium

• www.velleman.eu

Documents / Resources

| HQ POWER VDSSM5 Sound Mach V Portable DJ Set [pdf] User Manual
VDSSM5 Sound Mach V Portable DJ Set, VDSSM5, Sound Mach V Portable DJ Set, Portable DJ Set, DJ Set
---|---

References

• Details – Own brands – Velleman – Wholesaler and developer of electronics
• Velleman – Wholesaler and developer of electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>