Shark S6003EU Klik n’ Flip Automatic Steam Mop Owner’s Manual

S6003EU Klik n’ Flip Automatic Steam Mop
Owner’s Manual

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING YOUR SHARK® KLIK N’ FLIP SMARTRONIC DELUXE STEAM POCKET® MOP, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK KLIK N’ FLIP SMARTRONIC DELUXE STEAM POCKET MOP.
WARNING: DANGER OF SCALDING.
The steam emitted from the Steam Mop is very hot and may cause scalding.
Please use caution when using the Steam Mop.
WARNING: KEEP STEAM MOP AWAY FROM CHILDREN.
IMPORTANT:
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or  instruction concerning the use of the appliance by a person responsible for their safety.
WARNING: Children should be supervised to ensure that they do not play with the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. When in use never turn the Steam Mop over on its side or direct steam toward people, pets or plants.

2. Use the system only for its intended use.

3. DO NOT use for space-heating purposes.

4. DO NOT use outdoors.

5. DO NOT leave the appliance unattended when plugged in. Always unplug the power cord from the electrical outlet after use and before servicing.

6. DO NOT allow the Steam Mop to be used by children. Close attention is necessary when used near children, pets, or plants.

7. Use only as described in this owner’s guide.

8. Use only manufacturer’s recommended accessories.

9. DO NOT use with damaged cord or plug. If Steam Mop is not working as it should or has been dropped, damaged, leaking, left outdoors, or dropped into water, return it to Euro-Pro Europe Limited for  examination and repair.
   Incorrect reassembly or repair can cause a risk of electrical shock or injury when the Steam Mop is used.

10. To protect against a risk of electric shock, DO NOT immerse the Steam Mop in water or any other liquids.

11. DO NOT handle the plug or Steam Mop with wet hands or operate it without wearing shoes.

12. DO NOT pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run Steam Mop over cord. Keep cord away from heated surfaces.

13. DO NOT unplug by pulling on power cord. To unplug, grasp the plug not the power cord. Do not use extension cords or outlets with inadequate current-carrying capacity.

14. DO NOT put any objects into the the steam nozzle openings. Discontinue use if the steam nozzle is blocked.

15. DO NOT put hands or feet under the Steam Mop. It gets very hot.

16. Use ONLY on flat, horizontal surfaces. DO NOT use on walls, counters, or windows.

17. DO NOT use on leather, wax-polished furniture, synthetic fabrics, velvet, or other delicate, steam-sensitive materials.

18. DO NOT add cleaning solutions, scented perfumes, oils, or any other chemicals to the water used in the Steam Mop as this may damage it or make it unsafe for use. If you live in a hard-water area, we  recommend using distilled water in your Steam Mop. 19. Never leave any Dirt Grip™ pad in one spot while using or storing for any period of time, as this may damage your surfaces.

19. The liquid or steam must not be directed towards equipment containing electrical components, such as the interior of ovens.

20. You can release the Dirt Grip pad after you have unplugged the Steam Mop and allowed it to cool.

21. When cleaning the exterior of the Steam Mop, unplug the power cord from the electrical outlet and clean the Steam Mop with a dry or damp cloth. Do not pour water or use alcohol, benzene, or paint thinner on  the Steam Mop.

22. Extreme caution should be exercised when using the Steam Mop to clean stairs.

23. Never use Steam Mop without the Dirt Grip pad attached.

24. Keep your work area well lit.

25. Store Steam Mop indoors in a cool, dry place.

26. To avoid circuit overload, do not operate another appliance on the same socket (circuit) as the Steam Mop.

27. To avoid scalding injuries, always unplug and allow the Steam Mop to cool before removing or changing mop heads, accessories, or Dirt Grip pads.

WARNING: Your Steam Mop is designed to clean hard-floor surfaces that will withstand high heat. Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax and  on some no-wax floors, the sheen may be removed by the heat and steam action. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We also recommend that you check  the use and care instructions from the floor manufacturer.
This appliance complies with the WEEE-Directive 2012/19/EU on the disposal of electrical and electronic equipment (WEEE).
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material sources. To return your used device, please use the return and collection systems or contact the retailer where this product was purchased.
They can take this product for environmental safe recycling.
This appliance complies with the European directives for electromagnetic compatibility (EMC) 2014/30/EU and its revisions, as well as Low Voltage Directive (LVD) 2014/35/EU and its revisions.
Thank you for purchasing the Shark® Klik n’ Flip Smartronic Deluxe Steam Pocket® Mop.
This Owner’s Guide is designed to help you get a complete understanding of your new Klik n’ Flip Smartronic Deluxe Steam Pocket Mop. Please read it carefully and keep for future reference.
For a list of what is included with this model, refer to inside flap of box.
If you should have a question about your Shark Klik n’ Flip Smartronic Deluxe Steam Pocket Mop, please call Shark Customer Service
The Shark Klik n’ Flip Smartronic Deluxe Steam Pocket Mop is a complete solution for both deep steam cleaning and quick everyday cleaning. Whether you need to clean up tough stains with the Steam Blaster™ or  need to quickly handle a spill, our next-generation KLIK N’ Flip Mop Head and Dirt Grip™ Pads work with the Steam Pocket Mop to offer the ultimate in versatility and efficiency, making cleaning simple, quick and  easy.

REGISTER YOUR PURCHASE: sharkclean.eu
RECORD THIS INFORMATION:
Model Number: ____
Date of Purchase (Keep receipt): _____
TECHNICAL SPECIFICATIONS:
Voltage: 220-240v ~50/60Hz
Watts: 1200W
Water Capacity: 350 ml (11.8 oz.)
RECOMMENDED SCHEDULE FOR REPLACING WASHABLE DIRT GRIP PADS: Every 3 months
FOR BEST CLEANING PERFORMANCE:
See the Caring for Your Steam Pocket Mop section for more detail. Vacuum or sweep before mopping.

Getting Started

When assembling your Steam Mop there may be a little water in or around the water tank. This is because we test all our Steam Mops before you buy them, so you get a quality Shark® Klik n’ Flip Smartronic Deluxe  Steam Pocket® Mop.

Assembling Your Steam Pocket® Mop

WARNING: Always make sure the Steam Mop is UNPLUGGED when not in use. Never fill the Steam Mop or attach the mop head when the Steam Mop is plugged into an electrical outlet. Unplug from the  electrical outlet and allow to cool before you fill the Steam Mop, or attach or remove the head. To prolong the life of your Steam Mop, we recommend using distilled water. Make sure you add only water to the tank.  Chemicals or cleaning solutions (including vinegar) may damage the Steam Mop and could be unsafe for you and your family.
STEAM MOP ASSEMBLY

1. Insert the Steam Mop handle into the Steam Mop body. Push the handle in until you hear it click into place. (fig. 1)
2. Slide the Klik n’ Flip Mop Head into the Steam Mop body. Push until you hear it click securely into place. (fig. 1) To detach the Klik n’ Flip Mop Head, press the release button (fig. 2a) and slide off.
3. To attach the Dirt Grip pad, spread the pad on the floor with the pocket side up. Center the Klik n’ Flip Mop Head above the pad, then press the pad release button on the back of the Steam Mop body. (fig. 2a) Both sides of the Klik n’ Flip Mop Head will drop open. (fig. 2b) Slip the Klik n’ Flip Mop Head’s four corner tabs into the four corner pockets of the pad. (fig. 3 and fig. 4) Gently press one side of the Klik n’ Flip  Mop Head to the floor until that side clicks into place. (fig. 5) Repeat on the other side. (fig. 6)
4. Pull down on the water tank lid to open. (fig. 7)
5. Use the filling flask to pour water into the water tank. (fig. 8) Water can be poured into the tank directly.
   Do not overfill past the water line on the fill flask. Press the water tank lid firmly to close it.

Using Your Steam Pocket® Mop
IMPORTANT: Make sure you do not use the Steam Mop without attaching a Dirt Grip™ pad and adding water to the water tank first. When you are using the Steam Mop for the first time, it might take longer than  the normal 30 seconds to start steaming.
IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax and on some no-wax floors, the sheen may be removed by the heat and steam action. Test an  isolated area of the surface to be cleaned before proceeding. Check the use and care instructions from the floor manufacturer. ![Shark S6003EU Klik n' Flip Automatic Steam Mop

• Parts 4](https://manuals.plus/wp-content/uploads/2023/07/Shark-S6003EU- Klik-n-Flip-Automatic-Steam-Mop-Parts-4.png)

NOTE: To prolong the life of your Steam Mop, we recommend using distilled water.
NOTE: Sweep or vacuum your floors prior to cleaning with your Steam Mop.

1. Twist the Quick-Release Cord Holder to unwrap the power cord completely. (fig. 9) Plug into an electrical outlet.

2. When it’s first plugged in, the unit will be in Standby mode. The 3 lights below the Steam Control Button will blink to indicate Standby mode.

3. To select the steam mode, press the Steam Control Button once for LOW (1 blue light) twice for MED (2 blue lights) or three times for HI (3 blue lights).

4. Clean your floors with a forward and backward motion.

5. When you need an extra burst of steam to clean a stuck-on stain, you can use the Steam Blaster™ feature. Flip the head over so that it is behind themop body, then tilt the mop handle down. This will cause the  the Steam Blaster (fig. 10) to emit a concentrated blast of steam onto the stain.
   CAUTION: While in Steam Blaster mode, do not leave stationary for more than one minute.
   CAUTION: Do not scrub any one area for an extended period of time.

6. To stop the Steam Blaster spray, simply raise the handle. You can then flip the mop head back into its original position and continue cleaning.

7. When finished mopping, press the Steam Control Button. The three blue lights will blink, indicating that the unit is in Standby mode. Once in Standby mode, unplug the unit.

8. To remove the Dirt Grip™ pad, simply lift the Steam Mop straight up by the handle until the Klik n’ Flip Mop Head is hanging straight down. Press the Release button on the back of the Steam Mop body (fig  11a), and both sides of the head will drop open, releasing the pad. (fig 11b)

9. Once the Dirt Grip pad has been released, close the Klik n’ Flip Mop Head. To close, gently press one side of the Klik n’ Flip Mop Head to the floor until that side clicks into place. Repeat on the other side.

10. When the water tank is empty, the Steam Mop will stop producing steam. You can refill the water tank at any time as long as the Steam Mop is unplugged.
    Follow the water tank filling instructions on page 35.
    NOTE: Please wait 2 to 3 minutes for the Steam Mop to cool off before switching the mop head. Never leave the Steam Mop with a damp/wet Dirt Grip pad on any floor for an extended period of time.

Intelligent Steam Control®

The Shark® Klik n’ Flip Smartronic Deluxe Steam Pocket® Mop has 3 unique Intelligent Steam Control settings so you can use the right amount of steam for the cleaning task at hand. See below for tips on when to  use each setting.

Hardwood
Marble| Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
| Hardwood
Marble
Tile
Stone| Cleaning sealed surfaces and large areas
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate and heavy traffic areas
| Hardwood
Marble
Tile
Stone| Deep cleaning and cleaning hard-to-clean surfaces
Tough cleaning and removing stuck-on messes and stains
Deep cleaning heavy traffic areas
Cutting through heavy dirt and grime
Steam Blaster™| For an extra burst of steam, you can use the Steam Blaster feature in LOW, MED and HI.
Follow the instructions found on the “Using your Steam Pocket®  Mop” page.

TO SANITIZE* WITH THE STEAM MOP USING THE KLIK N’ FLIP MOP HEAD AND THE DIRT GRIP™ PAD:

1. Attach a clean Dirt Grip pad to the Klik N’ Flip Mop Head.
2. Plug in the unit and press the Steam Control Button to select the HI Setting.
3. Wait 30 seconds for the unit to begin producing steam.
4. Start mopping on an appropriate sealed hard-floor surface with a forward and backward motion. After three minutes, your unit is ready to be used to sanitize.
5. Using a forward and backward motion, move the unit over the area you seek to sanitize. Repeat at least 3 times.

• Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary.
  With Klik n’ Flip Mop in HI mode only when used with Steam Mop. Not in Steam Blaster mode.

Caring for Your Steam Pocket® Mop

AFTER USE AND STORAGE

1. Press the Steam Control Button until the three lights below start to blink, indicating that you are in Standby mode. Unplug the cord from the outlet and place the Steam Mop into the upright position. Let it cool.
2. To remove the Dirt Grip™ pad, lift the Steam Mop straight up by the handle until the Klik n’ Flip Mop Head is hanging straight down. Press the Release button on the back of the Steam Mop body, and both sides of the Klik n’ Flip Mop Head will drop open, releasing the pad. Once the pad has been released, close the Klik n’ Flip Mop Head.
3. If the Klik n’ Flip Mop Head is not attached to the mop, the pad can still be removed. Press the two red secondary pad release buttons located on the sides of the Klik n’ Flip Mop Head post to release the pad. (fig. 12)
4. Empty the water tank before storing. To empty the tank, hold the Steam Mop beside a sink. Open the water tank lid, then lean the unit over the sink. Let the water drain out, then close the lid.
5. To store the Steam Mop, wait until after it has cooled and the steam has been released. Then remove the Klik n’ Flip Mop Head and hang the Steam Mop by its handle on a large hook (not included). (fig. 13)
6. Store the filling flask by attaching it to the top handle pole of the Steam Mop.

DIRT GRIP PAD CARE INSTRUCTIONS
Care
Machine-wash the Dirt Grip pads separately with warm water using liquid detergent.
NEVER USE BLEACH, POWDERED DETERGENT, OR FABRIC SOFTENERS as they may damage or leave a coating on the Dirt Grip pads that will reduce their cleaning performance and absorbency. Dirt Grip pads should be line-dried or tumble- dried on a low setting, as this will extend the life of the microfiber fabric. (fi g. 14)
Loose fibers can indicate wearing of the microfiber fabric. Do not pull the loose fibers, as this can cause the weave to come undone. Simply trim the loose fibers with scissors. (fig. 15)
Replacement Dirt Grip pads
For best cleaning results, we recommend replacing your Dirt Grip pads every 3 to 4 months following normal use.
As with any fabric, dirt particles, grease, friction, and repeated washing can cause the fibers to break down, and you may notice an increase in the effort needed to push or pull the Steam Mop.
You can purchase replacement Dirt Grip pads and other accessories by visiting sharkclean.eu
STEAM NOZZLE CARE
If you believe the main steam nozzle or the Steam Blaster™ nozzle is clogged, please contact Customer
Service www.sharkclean.eu

Ordering Additional Accessories

ACCESSORY

Klik n’ Flip Mop Head
Great for all-purpose cleaning. Get an extra boost for tough stains from the Steam Blaster™, and cut your cleaning time in half with the hands-free two- sided pad.|
---|---
Dirt Grip™  Pad
Double-sided pad. Easy, hands-free installation and removal. Washable and reusable.|
Triangle Scrubber Head
Triangle shape is perfect for cleaning corners and hard-to-reach areas.
Equipped with a Steam Blaster to help loosen stains and a deployable scrubber to tackle stuck-on spots.|
Triangle Scrubber Pad
Ideal for cleaning corners and other hard-to-reach spaces. Easy to install and remove.|
Filling Flask
Filling line makes it simple and convenient to fill the water tank. Flask attaches to the handle for easy storage.|
Carpet Gider
Use to groom and freshen carpeting or area rugs.|

Troubleshooting Guide

plugged into an electrical outlet. Check your fuse or circuit breaker or  try a different outlet.
Make sure the water tank is full, the unit is plugged in, and the light around the Steam Control Button is solid.
If the lights below the Steam Control Button are not illuminated, try a different electrical outlet.
If the lights below the Steam Control Button are blinking, press the Steam Control Button to select a Steam setting.
If the lights below the Steam Control Button are solid, wait 30 seconds for the unit to warm up.
If after following the above steps the Steam Mop still does not produce any steam, contact Customer Service www.sharkclean.eu
The Steam Mop is producing  intermittent steam.| This is normal—for more consistent steam select the HI setting.
Also make sure the water tank is full.
I can’t select a Steam Setting.| Make sure the Steam Mop is plugged in and the lights below the Steam Control Button are solid.
If your Steam Mop is producing steam but the lights below the Steam Control Button are not lit, call customer service.
I am getting streaky/cloudy floors.| The Dirt Grip™  pad might be dirty. If it is, flip it over to the clean side or change it entirely. If you washed  the Dirt Grip pad with powdered detergent, then it could be damaged and require replacement.
This could also be an indication of soap or grease residue that has accumulated on the floor. As the Steam  Mop uses only a small amount of water, it may not be enough to rinse off the accumulation of residue that  the steam is bringing to the surface. We suggest rinsing the floor with nothing but water, letting it dry, and  then steam mopping again with a clean Dirt Grip pad. One or more rinses will generally remove the  residue.
A more stubborn case may require you to rinse the floor with a mix of one part vinegar and two parts  water (but DO NOT put any cleaning solutions or chemicals into the Steam Mop’s water tank.)
Please consult your flooring manufacturer’s care and maintenance instructions before applying any  cleaning products or solutions.
It’s really hard for me to push/pull  the Steam Mop.| The Steam Mopmight be hard to push/pull if the Dirt Grip pad isn’t wet enough. It should get easier to  push/pull the Steam Mop after it’s been running for a few minutes.
An overly dirty pad could also result in a harder push/pull experience. We recommend flipping the pad  over or using a clean pad.

Frequently Asked Questions

Can I use the Steam Mop on
carpets?| No, the Steam Mop is not designed for carpet cleaning.
What surfaces can I use the
Steam Mop on?| The Steam Mop is designed for use on all sealed hard-floor surfaces. We recommend that you first test an  isolated area of the floor surface to be cleaned as well as review the use and care instructions from your  floor manufacturer.
WARNING: Do not use on leather, wax-polished furniture, synthetic fabrics, velvet, or other delicate,  steam-sensitive materials.
NOTE: On surfaces treated with wax and on some no-wax floors, the sheen may be removed by the heat or  steam action of the unit. Test an isolated area of flooring first to see if sheen is affected.
Can I put something other than
water in the water tank of the
Steam Mop?| DO NOT add cleaning solutions, scented perfumes, oils, or any other chemicals to the water used in this  appliance, as this may damage the unit or make it unsafe for use. We recommend using distilled water in your Steam Mop.

Warranty Terms and Conditions

Warranty Terms and Conditions

At Shark we are so confident about the quality of our products that we give you an additional manufacturer’s warranty of up to two years. These terms and conditions relate to our manufacturer’s warranty only — your statutory rights are unaffected.

The conditions below describe the prerequisites and scope of our warranty. They do not affect your statutory rights or the obligations of your retailer and your contract with them.

Shark® Guarantees

A household appliance like a steam mop constitutes a sizeable investment. Your new machine needs to work properly for as long as possible. The guarantee it comes with is an important consideration – and reflects how much confidence the manufacturer has in its product and manufacturing quality.

Every Shark° machine comes with a free parts and labour guarantee. You’ll also find online support at www.sharkclean.eu

How do I register my extended Shark® guarantee?

You can register your guarantee online within 28 days of purchase. To save time, you’ll need the following information about your machine:

• Serial number (on the machine rating label)
• Date you purchased the machine (receipt or delivery note)
• To register online, please visit sharkclean.eu

IMPORTANT

• Both the 12 months and the extended 1 year guarantee will only cover your product from the date of purchase.
• Please keep your receipt at all times. Should you need to use your extended guarantee we will need your receipt to verify the information you have supplied to us is correct. The inability to produce a valid receipt may invalidate your guarantee.

What are the benefits of registering my free Shark® guarantee?
When you register your guarantee we’ll have your details to hand if we ever need to get in touch.You can also receive tips and advice on how to get the best out of your Shark° steam mop and hear the latest news about new Shark° technology and launches.
If you register your guarantee online, you’ll get instant confirmation that we’ve received your details.
How long are new Shark® machines guaranteed for?
Our confidence in our design and quality control means that your new Shark® steam mop is guaranteed for a total of two years. (12 months plus an extended warranty of 1 year).
What is covered by the free Shark® guarantee?
Repair or replacement of your Shark® machine (at Share’s discretion), including all parts and labour.A Shark® guarantee is in addition to your legal rights as a consumer.
What is not covered by the free Shark® guarantee?

• Blockages — For details of how to unblock your steam mop, please refer to the Operating Manual.
• Normal wear and tear.
• Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation or handling of the steam mop which is not in accordance with the Shark° Operating Manual supplied with your machine.
• Use of the steam mop for anything other than normal domestic household purposes.
• Use of parts not assembled or installed in accordance with the operating instructions.
• Use of parts and accessories which are not Shark° Genuine Components.
• Faulty installation (except where installed by Shark°).
• Repairs or alterations carried out by parties other than Shark or its agents.

What happens when my guarantee runs out?
Share does not design products to last for a limited time. We do appreciate that there may be a desire for our customers to want to repair their steam mops after the warranty has elapsed.
Where can I buy genuine Shark® spares and accessories?
Share spares and accessories are developed by the same engineers who developed your Shark° steam mop. You’ll find a full range of Shark° spares and replacement parts for all Shark° machines at www.sharkclean.eu.Accessories are at www.sharkclean.eu.
Please remember that using non-Shark® spares invalidates your guarantee.

Euro-Pro Europe Limited
15 Mariner Court
Calder Park
Wakefield
WF4 3FL
www.sharkclean.eu
S6003EU_40_IB_161104
© 2016 Euro-Pro Europe Limited
Shark and Steam Pocket are registered trademarks of Euro-Pro
Europe Limited. Dirt Grip, Spray Pocket and Steam Blaster are trademarks of Euro-Pro Europe Limited.
Illustrations may differ from actual product. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change
without notice.
PRINTED IN CHINA

References

• Shark Clean
• Shark Clean
• Shark® | Innovative Vacuum Cleaners, Mops & Home Care Products – Shark® is constantly evolving and innovating vacuums, floor care, and garment care products to meet the everyday needs of real people, like you.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>