VEVOR Cup Turner Tumbler Spinner Pen Turner with Epoxy Resin Kit User Manual
- June 12, 2024
- VEVOR
Table of Contents
VEVOR Cup Turner Tumbler Spinner Pen Turner with Epoxy Resin Kit
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us:
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there is any technology or software updates on our product.
SAFETY PRECAUTION
- Improper operation can result in injury. Improper operation may cause damage to the machine.
- This symbol indicates that the user should attach great importance to and pay attention to the triangular pattern. The left picture means “Beware of electrical shock”.
- This symbol indicates forbidden. The left picture means “No disassemble”.
- Do not use the power supply that does not meet the rated voltage. Use of a non-compliant power supply may result in fire or electric shock.
- When the machine smokes, emits peculiar smell, motor becomes noisy and other abnormal circumstances happens, please stop using. Keep using may cause fire or electric shock.
- It is forbidden to unplug the power supply when the machine is working. This will damage the machine.
- Ensure that the machine is grounded. Otherwise, electric shock or mechanical failure may occur.
- Do not disassemble, repair or correct the machine during use. Doing so can cause fire or electric shocks that can injure people.
- Attention
- Do not use in wet environment or contact with water. Do not infiltrate the liquid inside the machine, which will lead to short circuit and fire or electric shock.
- Do not touch the rotating rod or bearing part with your finger during use. This can cause finger injuries.
- Do not destroy or change the original power cord at will. Do not bend, pull, bind or press the power cord under heavy objects.
- If the machine will not in use for a long time, please unplug the power cord.
- Leakage protection switch devices must be installed for connecting sockets.
- The machine should be used on a firm, horizontal surface. Otherwise, the machine will fall, the use effect is not good, and even lead to injury.
- It is necessary to put the machine on a stable horizontal table when using it, otherwise the machine may fall down and even cause personal injury.
- Do not use the machine during thunderstorms and lightning, so as not to damage the machine.
PRODUCT DESCRIPTION
Technical Parameters
Standard Accessories
Product Structure
INSTALLATION AND INSTRUCTION
Tips!
- Prepare these tools in advance:
- Phillips screwdrivers, small wrenches, M4 countersunk screws, and M4 nuts.
- Install the baseboard, as shown in the figure.
- Install the holder kits, as shown in the figure.
- Install the rotary rods, as shown in the figure.
- Install the foams, as shown in the figure .
- Install the drying rack as shown in the following figure.
Tips!
- The motor supports dual rotation directions, but the direction can not be selected.
- The direction of motor rotation is affected by resistance. When the resistance is greater than the other direction, the steering direction will rotate to the direction with small resistance.
- When restarting after power failure, the direction is not fixed.
Type Z CONNECTION:
The supply cord cannot be replaced. If the cord is damaged the appliance
should be scrapped.
GUIDE FOR BEGINNERS
- Fix the cup and turn on the machine.
- Mixed epoxy resin (AB glue in 1 :1 ratio).
- Brush epoxy resin on the cups.
- Brush with glitter or paint as needed and wait 4 hours.
- Brush with epoxy again and wait 8 hours.
- Sand the surface as needed.
Note:
The above steps are only for reference. The specific operation will vary
according to the actual spraying requirements.
Cleaning Guidelines of Epoxy
- The epoxy resin is not completely solidified (soft state), just wipe with water or alcohol for cleaning.
- The epoxy resin has solidified and hardened. Blow it with a hair dryer or heat gun and wipe it with alcohol for cleaning.
Note
- When mixing epoxy, please use a heat gun or air dryer to speed up the mixing and make the mixture more uniform.
- Using a heat gun or a hair dryer to blow the surface of the cup after it has been coated with epoxy will reduce problems such as air holes and other defects.
APPLICATION RANGE
COMMON FAULT ANALYSIS
Dispose
This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, I but must be taken to a collection point for recycling electrical and electronic devices.
- Manufacturer: Zhongshan Qixiang Electrical Appliance Co., Ltd.
- Address: No.5, 12 Bihua Road, Baishi Village, Sanxiang Town, Zhongshan City, Guangdong Province China
- EU Importer: WAITCHX
- Address: 250 bis boulevard Saint-Germain 75007 Paris
- UK Importer: FREE MOOD LTD
- Address: 2 Holywell Lane, London, England, EC2A 3ET
EUREP GmbH
Unterlettenweg 1 a, 85051 lngolstadt, Germany
EUREP UK LTD
UNIT 2264, 100 OCK STREET, ABINGDON OXFORDSHIRE ENGLAND OX14 5DH
E-mail: CustomerService@vevor.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>