THE HOME DEPOT SCBSD0550 Datang 30 Inch Tall 3-Drawer White Bachelor’s Chest with Metal Legs Instruction Manual

SCBSD0550 Datang 30 Inch Tall 3-Drawer White Bachelor’s Chest with Metal Legs
Instruction Manual

NOTE:
This brochure contains IMPORTANT safety info. Please read and keep for future reference.

MAINTAINANCE AND WARNING

• Keep furniture away from heat.
• Do not clean furniture with harsh cleansers or polish. Do not use detergents, Solvents, abrasives, spray packs or leather cleaner. Use non-color mild soap with warm water clean spills(Mix 1:10 soap to water)
• Do not place furniture under direct sunlight, material will possibly fade over time.
• Do not use on site dry Cleaning machine.
• Children should not climb or jump on the furniture.
• Do not write on furniture without a padded barrier to protect the surface.
• Not for commercial use, For residential use only.

Weight Limitation
80LBS

overview

PARTS LIST

HARDWARE LIST

SPARE

Be sure to check all packing material carefully for small parts, which may have come loose inside the carton during shipment.

ASSEMBLY INSTRUCTIONS

STEP 1

Connect the part 8,9 with part 10.
Align the hole in part 8 and 9 to the hole in part 10 as the picture show. screw in the screw L and tighten by screwdriver R.
STEP 2

Connecting the part 11 to the finished part in step 1.
Align the groove in part 8,9 and 10. insert and slide down to the end. Be sure part 11 go into the groove of part 10!
STEP 3

Preparing the part 7

1. Align the hole in part 7 as the picture show, screw in the cam bolt A and tighten by screwdriver R.
2. Align the hole in part 7 to the hole in part F, screw in the screw G with part I and tighten by screwdriver R.

STEP 4

Connecting part 7 to the finished part in step 2.

1. Align the hole in part 8 and 9, insert the cam bolt A into the hole in part 9 and 8 as the picture show. then
2. Put the nut B into the hole from side, then tighten the nut by screwdriver R.
3. Last, peel the part J and cover the nut B for good looking.

STEP 5

Prepare the part 1

1. Align the hole in part 1 , insert the part D (wooden dowel) into the hole by hand;
2. Align the hole in part 1, screw in the cam bolt A into the hole and tighten by screwdriver R.

STEP 6

Prepare the part 3 and 4
Align the hole in part 3 and 4, screw in the cam bolt A into the hole and tighten by screwdriver R.

STEP 7

Assemble the part 1,3,4, and 14

1. Align the hole in part 14 to the cam bolt A in part 3 and 4, insert the cam bolt A , then put the NUT B into the hole as the picture show, screw and tighten the nut by screwdriver R. then,
2. Align the hole in part 3 and 4 to the part A and D in the part 1, insert the part A and D into the hole in part 3,4, put nut B into the hole and tighten by screwdriver R.
3. Use part J to cover the nut B for good looking.

STEP 8

Connect part 5 to the finished part in step 7

1. Align the hole in part 5 to the cam bolt A in part 1, insert the cam bolt A , then put the NUT B into the hole as the picture show, screw and tighten the nut B by screwdriver R. then,
2. Use part J to cover the nut B for good looking.

STEP 9

INSTALL part 6

1. Align the groove in part 1, 3,5 insert and slide the part 6 into the groove as the picture show. repeat the same way to finish the rest of part 6 in part 1, 4,5.
2. Align the hole in part 3 and 4, insert the part D into the hole by hand.

STEP 10

Connect part 2 to the finished part in step 9.

1. Align the hole in the part 2, insert the part D in part 3, 4 into part 2 , then.
2. Screw in the screw C and tighten by ALLENKEY K.

STEP 11

Connect the part 12 and part 13
Align the hole in part 13 to the hole in part 12, screw in the screw Q and tighten by Allen key K. Don’t fully tighten the screw Q!

STEP 12

Assemble the legs to the cabinet.

1. Align the hole in part 2 to the hole in part 12 and 13, screw in the screw P , then,
2. Fully tighten screw P in sequence by Allenkey K after all 6 screw P in the position.
3. Fully tighten the screw Q in sequence by Allenkey K.

STEP 13

Assemble part H to finished part in step 12.

1. Turn the cabinet upwards as the picture show;
2. Put the part H in the position as the picture show, then screw in the screw E and fully tighten by screwdriver R.

STEP 14

Assemble drawer to the cabinet

1. Find the moving part in male metal slider in drawer sides(pre-assembled ), be sure the moving part is in the back of metal slider as the picture show;
2. Find the moving part in female metal slider in the cabinet side(pre-assembled), be sure the moving part is in the front of metal slider as the picture show.
3. Align the male metal slider to the moving part in female metal slider, then push forward while two male sliders are in the moving part in female at the same time.
4. You can adjust the drawer to fit the cabinet once you need to do this. just loose the screw E , you can move the male metal slider to the position you expect, then fully tighten screw by screwdriver R.

STEP 15

Assemble part M

1. Align the hole in part M to the part 1 as the picture show, screw in the screw E and tighten by screwdriver R.
2. Use the adjust nail to keep the cabinet level in case wabbling.

STEP 16
Install the anti-collapse device.

1. Mark the position on the wall, this should be same as the position of M where are on the back of panel 1; Drilled and insert the expandable screw O by hammer;
2. Assemble the part M on the wall. Align the hole in the part M to the expandable screw O, Screw in screw L and tighten with screwdriver R.
3. let the plastic belt N go through the both M and pull to tighten.

Assembly Completed

WARRANTY

We strive to offer high-quality products, and we also try our best to satisfy each and every customer that orders from us with product or service as needed. We provide 30 days warranty starting from the time you receive the item. Each customer must provide a record of their order such as the order number, or item receipt for any items that are out of the warranty period you may also still receive replacement parts by purchasing them with our company if they are available.

Are you having difficulty with assembly?
Missing parts?
Please send email with your order No
customerservice@hulalahome.com
For return, Please check the return policy with the retailer or MarketPlace you bought from.
Appreciated your purchasing from us.
Pop up your life by our furniture piece!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>