VISUAL COMFORT CHO 7430 Albermarle Gas Post Light Instruction Manual

VISUAL COMFORT CHO 7430 Albermarle Gas Post Light

Product Information

• Product: Albermarle Gas Post Light
• Item: CHO 7430

Assembly Instructions

For Your Safety:

• Save these instructions for future reference.
• Please contact support@visualcomfort.com. for additional information on obtaining replacement parts.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Open fixture door (C), then install glass parts (H) to the fixture (D) and secure by bending metal tabs.
3. Install glass part (G) to fixture door (C) and secure by bending metal tabs, then close the door. See Diagram 1.
4. Connect gas tubing from the lantern to the gas source using the proper connection method.
5. Install fixture base (D) to post mount (F) and secure with screws (E).
6. Double-check gas connections and test for leaks before attempting to light the lantern.

Additional Hardware Included: For your convenience, 3/8 gas adapters and an additional 1/4 flare nut fitting are included inside the box. Discard if not required.

Lighting Instructions

1. Turn valve (A) to off position before turning on gas supply to the lantern. See Diagram 1.
2. Open the door and allow it to completely air out.
3. With lighter/flame above the burner tip (B), press in and turn valve (A) counter-clockwise approximately 30 degrees until a flame appears. See Diagram 2.
4. Adjust the flame to the desired height. Note: Do not operate the fixture with the gas valve fully open or flame height greater than 3.

Care Instructions

1. Allow the item to cool completely before cleaning.
2. Use a feather duster or soft cloth to clean the surface.
3. Use a damp towel to clean the glass.
4. Avoid using abrasives or chemical agents.

ASSEMBLY INSTRUCTIONS

FOR YOUR SAFETY

DANGER

FIRE OR EXPLOSION HAZARD If you smell gas

• Shut off gas to the appliance.
• Extinguish any open flame.
• If odor continues, leave the area immediately.
• After leaving the area, call your gas supplier or fire department.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• Fixtures must be installed at least 3″ from combustible walls and 12″ from combustible ceilings.
• Installation must conform with local codes or, in the absence of local codes, the National

Fuel Gas Code, ANSI Z223.1. Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Slotted Screwdriver

ASSEMBLY INSTRUCTIONS

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Open fixture door (C), then install glass parts (H) to fixture (D) and secure by bending metal tabs.
3. Install glass part (G) to fixture door (C) and secure by bending metal tabs, then close the door. See diagram 1.
4. Connect gas tubing from lantern to gas source using proper connection method.
5. Install fixture base (D) to post mount (F) and secure with screws (E).
6. Double check gas connections and test for leaks before attempting to light lantern.

ADDITIONAL HARDWARE INCLUDED: For your convenience, 3/8” gas adapters and additional 1/4″ flare nut fitting included inside box. Discard if not required.

LIGHTING YOUR LANTERN

1. Turn valve (A) to off position before turning on gas supply to lantern. See diagram 1.
2. Open door and allow to completely air out.
3. With lighter/flame above the burner tip (B), press in and turn valve (A) counter-clockwise approximately 30 degrees until flame appears. See diagram 2.
4. Adjust flame to desired height.
   • Note: Do not operate fixture with gas valve fully open or flame height greater than 3”.

ASSEMBLY INSTRUCTIONS

MAINTENANCE

CHECK BEFORE EVERY USE

1. Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
2. Check the burner area to ensure the flow of gas or combustion is never obstructed.
3. Always ensure proper ventilation before use.

CARE INSTRUCTION

1. Allow for the item to cool completely before cleaning.
2. Use a feather duster or soft cloth to clean the surface.
3. Use a damp towel to clean the glass.
4. No abrasives or chemical agents.

Save these instructions for future reference.
Please contact support@visualcomfort.com. for additional information on obtaining replacement parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>