VISUAL COMFORT TOB5586 Bryant Large Wrapped Billiard Instruction Manual

VISUAL COMFORT TOB5586 Bryant Large Wrapped Billiard

Product Information

• Product Name: Bryant Large Wrapped Billiard
• Item Number: TOB5586
• Package Contents: Light fixture, mounting plate, canopy, collar rings, threaded rod, coupling, fixture wires
• Bulbs: Not included (packaged separately)

NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

Product Usage Instructions

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from canopy (F) by removing collar rings (H).
3. Using the mounting plate (B) as a guide, line up with the junction box and mark anchor positions.
4. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into the holes using a hammer.
5. Install mounting plate (B) to the junction box and secure with mounting screws (D), then secure wood screws (C) to anchors (A).
6. Install threaded rod (P) to fixture body (Q), then connect rod (O) to fixture body (Q) and secure with coupling (N).
7. Feed fixture wires through threaded rod (M) and rod (L), then connect to couplings (N) and secure with couplings (K).
8. Continue feeding fixture wires through threaded rod (J), rod (I), collar ring (H), and canopy (F).
9. Holding the fixture upright, slide collar rings (H) and canopy (F) down rods and rest on top of rod (O). Then connect threaded rod (J) and rod (I) to coupling (K). NOTE: Slide components down slowly to avoid damages.
10. Hang fixture swivel balls (G) to the brackets of mounting plate (B). (see diagram 2)
11. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8inch.
12. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using a wire nut (E). NOTE: It is imperative that the fixture is grounded.
13. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using a wire nut (E).
14. Connect fixture hot wire (black) to the supply hot wire (usually black) using a wire nut (E). CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the junction box.
16. Install canopy (F) to mounting plate (B) and secure with collar rings (I).

NOTICE: This light fixture should be installed in accordance with all applicable,  local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item andcontents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Slotted Screwdriver
• Wire Cutters
• Slip Joint Pliers
• Wire Strippers

ASSEMBLY INSTRUCTIONS

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from the canopy (F) by removing collar rings (H).
3. Using the mounting plate (B) as a guide, line up with the junction box and mark anchor positions.
4. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into the holes using a hammer.
5. Install mounting plate (B) to the junction box and secure with mounting screws (D), then secure wood screws (C) to anchors (A).
6. Install threaded rod (P) to fixture body (Q), then connect rod (O) to fixture body (Q) and secure with coupling (N).
7. Feed fixture wires through threaded rod (M) and rod (L), then connect to couplings (N) and secure with couplings (K).
8. Continue feeding fixture wires through threaded rod (J) , rod (I), collar ring (H) and canopy (F).
9. Holding fixture upright, slide collar rings (H), canopy (F) down rods and rest on top of rod (O). Then connect threaded rod (J) and rod (I) to coupling (K).
   • NOTE: Slide components down slowly to avoid damage.
10. Hang fixture swivel balls (G) to the brackets of the mounting plate (B). (see diagram 2)
11. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8”.
12. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (E).
    • NOTE: It is imperative that the fixture is grounded.
13. Connect the fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (E).
14. Connect the fixture hot wire (black) to the supply hot wire (usually black) using wire nut (E).
    • CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck them into the junction box.
16. Install canopy (F) to mounting plate (B) and secure with collar rings (I).
17. Install light bulbs into sockets.
18. Attach shades (S) to the top of socket cups and secure them with knurled rings (M).
    • NOTE: If the shade has additional packaging, carefully cut it off from the interior of the shade to avoid damage.
    • Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>