VISUAL COMFORT ARN5522 Valencia Grande Nine Light Chandelier Instruction Manual

VISUAL COMFORT ARN5522 Valencia Grande Nine Light Chandelier

Product Information

Model: ARN5522
The Valencia Grande Nine Light Chandelier is a stylish and elegant lighting fixture that adds a touch of sophistication to any space. With its nine lights, it provides ample illumination, making  it perfect for larger rooms or areas that require bright lighting.This chandelier is designed to be installed in accordance with local installation codes and should be handled by someone familiar with its construction and operation. Please inspect the item and its contents carefully before installation, and retain all packaging material until the installation is complete and approved.

Product Usage Instructions

1. Carefully remove all parts from the box and place them on a clean, soft surface.
2. Remove the mounting plate (B) from the canopy (I) by removing the collar ring (J).
3. Install the mounting plate (B) to the junction box and secure it with the provided mounting screws (F).
4. Install the fixture arms (M, N, O) to the fixture hub (X) and secure them.
5. Feed the electrical wires through the bottom rod (L) and thread them to the connector on top of the hub (X). Repeat this step for the middle rod (K), connecting it to the bottom rod (L).
6. Continue feeding the wires through the collar ring (J), canopy (I), and top rod (H).
7. Holding the fixture upright, slide the collar ring (J) and canopy (I) down the bottom rods (L) and rest them on the fixture. Then connect the top rod (H) to the middle rod (K). Note: Slide the components down slowly to avoid damages.
8. Hang the fixture fan mount (G) to the center of the mounting plate (B) and secure it with the provided set screw (C) using a screwdriver.
9. Cut the excess wires, leaving enough length to reach the junction box. Separate the wires and strip insulation on each end.
10. Connect the supply ground wire (usually green or bare copper) around the green grounding screw.
11. Connect the fixture neutral wire (black) to the driver output wire (black) using a wire nut (A).
12. Connect the fixture hot wire (red) to the driver output wire (red) using a wire nut (A). Caution: Do not reverse the hot and neutral connections.
13. Connect the driver input neutral wire (white) to the supply neutral wire (usually white) using a wire nut (A).
14. Connect the driver input hot wire (black) to the supply hot wire (usually black) using a wire nut (A). Caution: Do not reverse the hot and neutral connections.

Note: It is imperative that the fixture is properly grounded for safety.
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Slotted Screwdriver
• Wire Cutters
• Wire Strippers
• Slip-joint pliers

ASSEMBLY INSTRUCTIONS

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from the canopy (I) by removing collar ring (J).
3. Install mounting plate (B) to the junction box and secure with mounting screws (F).
4. Install fixture arms (M & N & O) to fixture hub (X) and secure with lock washer (Y) and screws (Z) using a provided wrench (E). See diagram 1 & 2.
5. Connect 3 jumper neutral wires to fixture neutral wire (black) and secure using wire nut (A). Divide arm neutral wires (black) by section and connect to jumper neutral wires, securing with wire nut (A). See diagram 3.
   • NOTE: Divide sections of neutral wire evenly to jumper wires as shown in diagram 3.
6. Connect 3 jumper hot wires to fixture hot wire (red) and secure using wire nut (A). Divide arm hot wires (red) by section and connect to jumper hot wires, securing with wire nut (A). See diagram 3.
   • NOTE: Divide sections of hot wire evenly to jumper wires as shown in diagram 3.
   • CAUTION: Do not reverse the hot and neutral connections.
7. Install metal plate (T) to hub (X) and secure with hex nut (U).
8. Install cap (V) to hub (X) and secure with final (W).
9. Feed electrical wires through the bottom rod (L) and thread to the connector on top of the hub (X). Repeat for middle rod (K), connecting to the bottom rod (L).
10. Continue feeding wires through collar ring (J), canopy (I), and top rod (H).
11. Holding the fixture upright, slide collar ring (J) and canopy (I) down bottom rods (L) and rest on the fixture. Then connect the top rod (H) to the middle rod (K).
    • NOTE: Slide components down slowly to avoid damage.
12. Hang fixture fan mount (G) to the center of mounting plate (B) and secure with set screw (C) using a provided screwdriver (D). See diagram 4.
13. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.
14. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 4). Tighten.
    • NOTE: It is imperative that the fixture is grounded.
15. Connect fixture neutral wire (black) to driver output wire (black) using wire nut (A).
16. Connect fixture hot wire (red) to driver output wire (red) using wire nut (A).
    • CAUTION: Do not reverse the hot and neutral connections.
17. Connect the driver input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
18. Connect the driver input hot wire (black) to the supply hot wire (usually black) using wire nut (A).
    • CAUTION: Do not reverse the hot and neutral connections.
19. Connect the driver input hot wire (black) to the supply hot wire (usually black) using wire nut (A).
    • CAUTION: Do not reverse the hot and neutral connections.
20. Make sure all wire connections are tight, then carefully tuck them into the junction box.
21. Insert driver into the center of mounting plate (B).
22. Install canopy (I) to mounting plate (B) and secure with collar ring (J).
23. Thread rods (P) to the fixture.
24. Remove thumbscrews (Q) from rods (P), then line up holes from the bowl (S) to rods (P) and secure with thumbscrews (Q). Repeat with the remaining parts.
    • Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>