WORLD EYECAM 1008 Vandal Proof Dome Network Camera User Guide
- June 12, 2024
- WORLD EYECAM
Table of Contents
1008 Vandal Proof Dome Network Camera
Product Information
The Vandal Proof Dome Network Camera is a surveillance camera
designed for indoor use. It is built to withstand vandalism and
tampering attempts, making it ideal for high-risk areas. The camera
features a Complementary Metal-Oxide Semiconductor (CMOS) image
sensor for high-quality video capture. It also comes with advanced
features such as motion detection, night vision, and remote viewing
capabilities.
Product Usage Instructions
-
Upgrade the reader software: If you are unable to open
the manual (in PDF format), try upgrading the reader software or
using other mainstream reader software. -
Electrical safety: Before operating the device, ensure
that the power source conforms to the Safety Extra Low Voltage
(SELV) standard and supplies power with the rated voltage specified
on the device label. Incorporate a readily accessible disconnect
device in the building installation wiring. Take precautions to
prevent the power cable, plug, power socket, and device junction
from being trampled or pressed. -
Environment: Avoid aiming the device at strong light
sources such as lamp light and sunlight, as it may cause over
brightness or light marks on the video. Do not place the device in
damp or dusty environments, extremely hot or cold temperatures, or
areas with strong electromagnetic radiation or unstable lighting.
Keep the device away from liquids and ensure sound ventilation to
prevent heat accumulation. During transportation, storage, and
installation, avoid heavy stress, violent vibration, and water
splash. Use the standard factory packaging or equivalent material
when transporting the device. -
Operation and Daily Maintenance: Avoid touching the heat
dissipation component of the device to prevent scalding. Follow the
instructions in the manual for any disassembly operations. Connect
the grounding hole to enhance the device’s reliability. When
cleaning, use an air blower to remove dust and dirt from the CMOS
image sensor. For stubborn stains, gently wipe the lens with a soft
cloth moistened with alcohol. Clean the device body with a soft dry
cloth, and if necessary, use a mild detergent on the cloth. Avoid
using volatile solvents or strong abrasive detergents, as they may
damage the device body coating and reduce performance.
For any problems or uncertainties regarding the device, please
visit our website, contact the supplier, or reach out to our
customer service for assistance. Refer to our final explanation for
any unresolved controversies.
Vandal Proof Dome Network Camera
Quick Start Guide
V1.0.3
Quick Start Guide
Upgrade the reader software or try other mainstream reader software if the
manual (in PDF format) cannot be opened.
All trademarks, registered trademarks and the company names in the manual are
the properties of their respective owners.
Please visit our website, contact the supplier or customer service if there is
any problem occurred when using the device.
If there is any uncertainty or controversy, please refer to our final
explanation.
II
Quick Start Guide
Important Safeguards and Warnings
Electrical safety
All installation and operation should conform to your local electrical safety
codes. The power source shall conform to the Safety Extra Low Voltage (SELV)
standard, and supply
power with rated voltage which conforms to Limited Power Source requirement
according to IEC60950-1. Please note that the power supply requirement is
subject to the device label. Make sure the power supply is correct before
operating the device. A readily accessible disconnect device shall be
incorporated in the building installation wiring. Prevent the power cable from
being trampled or pressed, especially the plug, power socket and the junction
extruded from the device.
Environment
Do not aim the device at strong light to focus, such as lamp light and sun
light; otherwise it might cause over brightness or light marks, which are not
the device malfunction, and affect the longevity of Complementary Metal-Oxide
Semiconductor (CMOS).
Do not place the device in a damp or dusty environment, extremely hot or cold
temperatures, or the locations with strong electromagnetic radiation or
unstable lighting.
Keep the device away from any liquid to avoid damage to the internal
components. Keep the indoor device away from rain or damp to avoid fire or
lightning. Keep sound ventilation to avoid heat accumulation. Transport, use
and store the device within the range of allowed humidity and temperature.
Heavy stress, violent vibration or water splash are not allowed during
transportation, storage
and installation. Pack the device with standard factory packaging or the
equivalent material when transporting
the device. Install the device in the location where only the professional
staff with relevant knowledge of
safety guards and warnings can access. The accidental injury might happen to
the non-professionals who enter the installation area when the device is
operating normally.
Operation and Daily Maintenance
Do not touch the heat dissipation component of the device to avoid scald.
Carefully follow the instructions in the manual when performing any
disassembly operation
about the device; otherwise, it might cause water leakage or poor image
quality due to unprofessional disassembly. Please make sure that the gasket
ring is flat and properly installed in the groove before installing the cover.
Please contact after-sale service for desiccant replacement if there is
condensed fog on the lens after unpacking or when the desiccant turns green
(Not all models are included with the desiccant). It is recommended to use the
device together with lightning arrester to improve lightning protection
effect.
III
Quick Start Guide
It is recommended connect the grounding hole to the ground to enhance the
reliability of the device.
Do not touch the image sensor directly (CMOS). Dust and dirt could be removed
with air blower, or you can wipe the lens gently with soft cloth that
moistened with alcohol.
Device body can be cleaned with soft dry cloth, which can also be used to
remove stubborn stains when moistened with mild detergent. To avoid possible
damage on device body coating which could cause performance decrease, do not
use volatile solvent such as alcohol, benzene, diluent and so on to clean the
device body, nor can strong, abrasive detergent be used.
Dome cover is an optical component, do not touch or wipe the cover with your
hands directly during installation or operation. For removing dust, grease or
fingerprints, wipe gently with moisten oil-free cotton with diethyl or moisten
soft cloth. You can also air blower to remove dust. WARNING
Please strengthen the protection of network, device data and personal
information by adopting measures which include but not limited to using strong
password, modifying password regularly, upgrading firmware to the latest
version, and isolating computer network. For some device with old firmware
versions, the ONVIF password will not be modified automatically along with the
modification of the system password, and you need to upgrade the firmware or
manually update the ONVIF password.
Use standard components or accessories provided by manufacturer and make sure
the device is installed and maintained by professional engineers.
The surface of the image sensor should not be exposed to laser beam radiation
in an environment where a laser beam device is used.
Do not provide two or more power supply sources for the device unless
otherwise specified. A failure to follow this instruction might cause damage
to the device.
IV
Quick Start Guide
Table of Contents
Foreword……………………………………………………………………………………………………………………………………….. I Important
Safeguards and Warnings………………………………………………………………………………………………. III 1
Introduction………………………………………………………………………………………………………………………………… 1
Cable ………………………………………………………………………………………………………………………………………………………………………..1
Connecting Alarm Input/output ………………………………………………………………………………………………………………………… 2
2 Network Configuration ………………………………………………………………………………………………………………… 4
Initializing Device…………………………………………………………………………………………………………………………………………………..4
Modifying Device IP Address ……………………………………………………………………………………………………………………………….
5 Logging in to Web Interface
………………………………………………………………………………………………………………………………..6 3
Installation………………………………………………………………………………………………………………………………….. 8 Packing
List……………………………………………………………………………………………………………………………………………………………..8
Dimension………………………………………………………………………………………………………………………………………………………………. 8
Installing Device …………………………………………………………………………………………………………………………………………………….9
3.3.1 Installation Method……………………………………………………………………………………………………………………………………9
3.3.2 Installing SD Card (Optional)
…………………………………………………………………………………………………………………… 9 3.3.3 Attaching
Device………………………………………………………………………………………………………………………………………10 3.3.4 Installing
Waterproof Connector …………………………………………………………………………………………………………..12 3.3.5
Adjusting Angle………………………………………………………………………………………………………………………………………..13
V
Alarm output
Quick Start Guide
Log in web interface, and configure alarm input and alarm output in alarm
setting. The alarm input in the web interface is corresponding to the alarm
input end of the I/O
port. There will be high level and low level alarm signal generated by the
alarm input device when alarm occurs, set the input mode to “NO” (default) if
the alarm input signal is logic “0” and to “NC” if the alarm input signal is
logic “1”. The alarm output in the web interface is corresponding to the alarm
output end of the device, which is also alarm output end of the I/O port.
3
2 Network Configuration
Quick Start Guide
Device initialization and IP setting can be finished with the “ConfigTool” or
in web interface. For more information, see the WEB Operation Manual.
Device initialization is available on select models, and it is required at
first use and after device is being reset.
Device initialization is available only when the IP addresses of the device
(192.168.1.108 by default) and the PC stays in the same network segment.
Planning useable network segment properly to connect the device to the
network. The following figures and interfaces are for reference only, and the
actual product shall prevail.
Initializing Device
Double-click “ConfigTool.exe” to open the tool. Click . The Modify IP
interface is displayed. See Figure 2-1.
Modify IP interface
Click Search setting. The Setting interface is displayed. Enter the start IP
and end IP of the network segment in which you want to search devices, and
then click OK. All the devices found in the network segment are listed. Select
one or several devices whose Status is Uninitialized, and then click
Initialize.
4
The Device initialization interface is displayed. Select the devices that need
initialization, and then click Initialize. The password setting interface is
displayed. See Figure 2-2.
Password setting interface
Quick Start Guide
Set and confirm the password of the devices, and then enter a valid email
address. Click Next. The final setting interface is displayed.
Password can be modified or reset in System Settings. Select the options
according to your needs and then click OK. The Initialization interface is
displayed after initializing is completed. Click the success icon ( ) or the
failure icon ( ) for the details. Click Finish. The device status in the
Modify IP interface (Figure 2-1) turns to Initialized.
Modifying Device IP Address
You can modify IP address of one or multiple devices in one time. This section
is based on modifying IP addresses in batch.
Modifying IP addresses in batch is available only when the corresponding
devices have the same login password. Follow Step 1 to Step 4 in 2.1 to search
devices in your network segment.
After clicking Search setting, please make sure the username and password are
the same as what you set during initialization, otherwise there will be “wrong
password” notice.
5
Quick Start Guide
Select the devices which IP addresses need to be modified, and then click
Modify IP. The Modify IP Address interface is displayed. See Figure 2-3.
Modify IP Address interface
Select Static mode and enter start IP, subnet mask and gateway. IP addresses
of multiple devices will be set to the same if you select Same IP. If DHCP
server is available in the network, devices will automatically obtain IP
addresses from DHCP server when you select DHCP. Click OK.
Logging in to Web Interface
Open IE browser, enter the IP address of the device in the address bar and
press Enter. If the setup wizard is displayed, follow the instructions to
finish the settings. Enter user name and password in the login box, and then
click Login. For first time login, click Click Here to Download Plugin and
install the plugin as instructed. The main interface is displayed when the
installation is finished. See Figure 2-4.
6
Main interface
Quick Start Guide
7
3 Installation
Quick Start Guide
Packing List
The tools required for the installation including electric drill is not
provided in the packing. The operation manual and related tool are contained
in the disk or the QR code, and the actual
packing shall prevail.
Dimension
Following figures are for reference only, the actual product shall prevail.
(Unit: mm [in])
8
Installing Device
3.3.1 Installation Method
Quick Start Guide
3.3.2 Installing SD Card (Optional)
SD card slot is available on select models. Disconnect the power from the
device before installing the SD card.
9
Quick Start Guide
Pressing reset button: Short press reset button for 1-2 s, press WPS button on
the router and the device can be
connected to corresponding router within 1 minute (only supported by some
models). Press the reset button for 10 seconds to reset the device.
3.3.3 Attaching Device
Make sure the mounting surface is strong enough to hold at least three times
of the device weight.
10
Cable going through the mounting surface
Quick Start Guide
11
Cable going through the side cable tray
Quick Start Guide
3.3.4 Installing Waterproof Connector
This part is only needed when a waterproof connector comes with the device and
the device is used outdoor.
12
Quick Start Guide
3.3.5 Adjusting Angle
Vertical rotation ring is available on select models, which fails to support
image rotation. Please refer to the real model for more details.
IR light layout is different according to different models; please refer to
the real model for more details.
Please be aware of image rotation direction when it turns to 64° vertically,
which is to avoid IR light being blocked by enclosure and causing bad IR
effect.
13
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>