WORLD EYECAM 1030 Vandal Proof Dome Network Camera User Manual

WORLD EYECAM 1030 Vandal Proof Dome Network Camera User Manual

Foreword

General

This manual introduces the functions, installation and operations of the camera.

Safety Instructions

The following categorized signal words with defined meaning might appear in the manual.

could result in slight or moderate injury.

CAUTION| Indicates a potential risk which, if not avoided, may result in property damage, data loss, lower performance, or unpredictable result.
NOTE| Provides additional information as the emphasis and supplement tothe text.

Revision History

About the Manual

• The manual is for reference only. If there is inconsistency between the manual and the actualproduct, the actual product shall prevail.We are not liable for any loss caused by the operations that do not comply with the manual.
• The manual would be updated according to the latest laws and regulations of related regions.
• For detailed information, see the paper manual, CD-ROM, QR code or our official website. Ifthere is inconsistency between paper manual and the electronic version, the electronic versionshall prevail.
• All the designs and software are subject to change without prior written notice. The productupdates might cause some differences between the actual product and the manual. Pleasecontact the customer service for the latest program and supplementary documentation.
• There still might be deviation in technical data, functions and operations description, or errorsin print. If there is any doubt or dispute, please refer to our final explanation.
• Upgrade the reader software or try other mainstream reader software if the manual (in PDFformat) cannot be opened.
• All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners.
• Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device.
• If there is any uncertainty or controversy, please refer to our final explanation.

Important Safeguards and Warnings

Electrical safety

• All installation and operation should conform to your local electrical safety codes.
• The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supplypower with rated voltage which conforms to Limited Power Source requirement according toIEC60950-1. Please note that the power supply requirement is subject to the device label.
• Make sure the power supply is correct before operating the device.
• A readily accessible disconnect device shall be incorporated in the building installation wiring.
• Prevent the power cable from being trampled or pressed, especially the plug, power socket and the junction extruded from the device.

Environment

• Do not aim the device at strong light to focus, such as lamp light and sun light; otherwise it might cause over brightness or light marks, which are not the device malfunction, and affectthelongevity of Complementary Metal-Oxide Semiconductor (CMOS).
• Do not place the device in a damp or dusty environment, extremely hot or cold temperatures, orthe locations with strong electromagnetic radiation or unstable lighting.
• Keep the device away from any liquid to avoid damage to the internal components.
• Keep the indoor device away from rain or damp to avoid fire or lightning.
• Keep sound ventilation to avoid heat accumulation.
• Transport, use and store the device within the range of allowed humidity and temperature.
• Heavy stress, violent vibration or water splash are not allowed during transportation, storageand installation.
• Pack the device with standard factory packaging or the equivalent material when transportingthe device.
• Install the device in the location where only the professional staff with relevant knowledge of safety guards and warnings can access. The accidental injury might happen to the non-professionals who enter the installation area when the device is operating normally.

Operation and Daily Maintenance

• Do not touch the heat dissipation component of the device to avoid scald.

• Carefully follow the instructions in the manual when performing any disassembly operationabout the device; otherwise, it might cause water leakage or poor image quality due tounprofessional disassembly. Please make sure that the gasket ring is flat and properly installedin the groove before installing the cover. Please contact after-sale service for desiccantreplacement if there is condensed fog on the lens after unpacking or when the desiccant turnsgreen (Not all models are included with the desiccant).

• It is recommended to use the device together with lightning arrester to improve lightningprotection effect.

• It is recommended connect the grounding hole to the ground to enhance the reliability of the
  device.

• Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air blower,oryou can wipe the lens gently with soft cloth that moistened with alcohol.

• Device body can be cleaned with soft dry cloth, which can also be used to remove stubborn stains when moistened with mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive detergent be used.

• Dome cover is an optical component, do not touch or wipe the cover with your hands directly during installation or operation. For removing dust, grease or fingerprints, wipe gently with moisten oil-free cotton with diethyl or moisten soft cloth. You can also air blower to remove dust.

WARNING

• Please strengthen the protection of network, device data and personal information by adopting measures which include but not limited to using strong password, modifying password regularly, upgrading firmware to the latest version, and isolating computer network. For some device with old firmware versions, the ONVIF password will not be modified automatically along with the modification of the system password, and you need to upgrade the firmware or manually update the ONVIF password.
• Use standard components or accessories provided by manufacturer and make sure the device isinstalled and maintained by professional engineers.
• The surface of the image sensor should not be exposed to laser beam radiation in anenvironment where a laser beam device is used.
• Do not provide two or more power supply sources for the device unless otherwise specified. A failure to follow this instruction might cause damage to the device.

Introduction

Cable

• Cable type might vary with different devices, and the actual product shall prevail.
• Please waterproof all the cable joints with insulating tape and waterproof tape to avoid shortcircuit and water damage. For the detailed operation, see the FAQ Manual.
  

For more information about cable ports, see Table 1-1.

Table 1-1 Cable information

Audio input port is available on select model.
2| Audio output| Connects to speaker to output audio signal.
Audio output port is available on select model.
3| Ethernet port| Connects to network with network cable.
Provides power to the device with
PoE.PoE is available on select model.
4| Alarm 1/0| Includes alarm signal input and output ports, the number of 1/0 ports might vary on different devices. For detailed information, see “Table 1-2 Alarm information.”
5| 12V DC power input| Inputs 12V DC power. Please be sure to supply power as instructed in the Guide.Device abnormity or damage could occur if power is not supplied correctly.

For more information about I/0 port, see Table 1-2.

Table 1-2 Alarm information

Connecting Alarm Input/output

Alarm input/output is available on select models.

Step 1 Connect alarm input device to the alarm input end of the I/O port, see Figure 1-2. Device collects different states of alarm input port when the input signal is idling and being grounded.

• Device collects logic “1” when input signal is connecting to +3V to +5V or idling.
• Device collects logic “0” when input signal is grounded.
  

Step2 Connect alarm output device to the alarm output end of the I/O port. The alarm output is the open-collector output.

• Alarm output: alarm output is OD door, it needs to add pull-up resistor externally (Typical value 10 KQ) to make it work normally. The output signal is high level bydefault (external pull-up voltage) after adding external pull-up resistor; the output signal becomes low level when there is alarm output.
• The operating current of alarm output port is recommended to be less than 10mA. The max current which is used to drive external circuit is 80mA, it is recommended to add relay externally when it is beyond the value.
  

Step 3 Log in web interface, and configure alarm input and alarm output in alarm setting.

• The alarm input in the web interface is corresponding to the alarm input end of the I/0port. There will be high level and low level alarm signal generated by the alarm inputdevice when alarm occurs, set the input mode to “NO” (default) if the alarm input signalis logic “0” and to “NC” if the alarm input signal is logic “1”.
• The alarm output in the web interface is corresponding to the alarm output end of thedevice, which is also alarm output end of the I/O port.

Network Configuration

Device initialization and IP setting can be finished with the “ConfigTool” orin web interface. For more information, see the WEB Operation Manual.

• Device initialization is available on select models, and it is required at first use and after device is being reset.
• Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the PC stays in the same network segment.
• Planning useable network segment properly to connect the device to the network.
• The following figures and interfaces are for reference only, and the actual product shall prevail.

Initializing Device

Step 1 Double-click “ConfigTool.exe” to open the tool.

Step2 Click
The Modify IP interface is displayed. See Figure 2-1. Figure 2-1 Modify IP interface

Step 3 Click Search setting.
The Setting interface is displayed.

Step4 Enter the start IP and end IP of the network segment in which you want to search devices, and then click OK. All the devices found in the network segment are listed.

Step 5 Select one or several devices whose Status is Uninitialized, and then click Initialize.

The Devic ization interface is displayed.

Step 6 Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting interface

Step 7 Set and confirm the password of the devices, and then enter a valid email address.
Click Next.

The final setting interface is displayed.

Password can be modified or reset in System Settings.

Step8 Select the options according to your needs and then click OK.
The Initialization interface is displayed after initializing is completed. Click the success icon ( ) or the failure icon (  ) for the details.

Step 9 Click Finish.
The device status in the Modify IP interface (Figure 2-1) turns to Initialized.

Modifying Device IP Address

• You can modify IP address of one or multiple devices in one time. This section is based on modifying IP addresses in batch.
• Modifying IP addresses in batch is available only when the corresponding devices have the same login password.

Step 1 Follow Step 1 to Step 4 in 2.1 to search devices in your network segment.

After clicking Search setti g, please make sure the username and password are the same
as what you set during initialization, otherwise there will be “wrong password” notice.

Step 2 Select the devices which IP addresses need to be modified, and then click Modify IP. The Modify IP Address interface is displayed. See Figure 2-3. Figure 2-3 Modify IP Address interface

Step 3 Select Static mode and enter start IP, subnet mask and gateway.

• IP addresses of multiple devices will be set to the same if you select Same IP.
• If DHCP server is available in the network, devices will automatically obtain IP addresses from DHCP server when you select DHCP.

Step 4 Click OK.

Logging in to Web Interface

Step 1 Open IE browser, enter the IP address of the device in the address bar and press Enter.If the setup wizard is displayed, follow the instructions to finish the settings.

Step 2 Enteruser name and password in the login box, and then click Login.

Step 3 Forfirst time login, click Click Here to Download Plugin and install the plugin as instructed.The main interface is displayed when the installation is finished. See Figure 2-4.

Packing List

• The tools required for the installation including electric drill is not provided in the packing.
• The operation manual and related tool are contained in the disk or the QR code, and the actual packing shall prevail.
  

Dimension

Following figures are for reference only, the actual product shall prevail.

Installation Method

Installing SD Card (Optional)

SD card slot is available on select models.
Disconnect the power from the device before installing the SD card.

Pressing reset button:

• Short press reset button for 1-2 s, press WPS button on the router and the device can be connected to corresponding router within 1 minute (only supported by some models).
• Press the reset button for 10 seconds to reset the device.

Attaching Device

Make sure the mounting surface is strong enough to hold at least three times of the device weight.

Cable going through the mounting surface

Cable going through the side cable tray

Installing Waterproof Connector

This part is only needed when a waterproof connector comes with the device and the device is used outdoor.

Adjusting Angle

• Vertical rotation ring is available on select models, which fails to supportimage rotation. Please refer to the real model for more details.
• IR light layout is different according to different models; please refer to the real model for more details.
• Please be aware of image rotation direction when it turns to 64° vertically, which is to avoid IR light being blocked by enclosure and causing bad IR effect.
  

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>