VISUAL COMFORT ARN 2018 Drunmore Single Sconce Instruction Manual
- June 12, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT ARN 2018 Drunmore Single Sconce
Product Information
| Product Name | Drunmore Single Sconce |
|---|---|
| Item Number | ARN 2018 |
| Version | Metal Version |
| Notice | This light fixture should be installed in accordance with all |
applicable, local installation codes, and by a person familiar with
the construction and operation of it, as well as the hazards
involved. Inspect item and contents carefully. If any damage or
defect is found, do not install. Retain all packaging material
until installation is complete and approved.
Care Instructions| Clean only with a soft dry cloth or feather duster. Do not
use
abrasive or chemical agents.
Product Usage Instructions
Drunmore Single Sconce
Item # ARN 2018
NOTICE :
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
- Phillips Screwdriver
- Slotted Screwdriver
Assembly Instructions – Metal Version
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove mounting plate (B) from fixture (D) by removing screws (E).
-
Install mounting plate (B) to the junction box and secure with mounting screws (C).
-
Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
NOTE: It is imperative that the fixture is grounded. -
Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
-
Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections. -
Make sure all wire connections are tight, then carefully tuck into the junction box.
-
Install fixture (D) to mounting plate (B) and secure with screws (E).
-
Remove socket ring (G) from socket (F), then install shade (G) to socket (F) and secure with socket ring (H).
-
Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
Drunmore Single Sconce
Item # ARN 2018
NOTICE :
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
- Phillips Screwdriver
- Slotted Screwdriver
Assembly Instructions – CG Version
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove mounting plate (B) from fixture (D) by removing screws (E).
-
Install mounting plate (B) to the junction box and secure with mounting screws (C).
-
Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
NOTE: It is imperative that the fixture is grounded. -
Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
-
Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections. -
Make sure all wire connections are tight, then carefully tuck into the junction box.
-
Install fixture (D) to mounting plate (B) and secure with screws (E).
-
Remove socket ring (G) from socket (F), then install shade (G) to socket (F) and secure with socket ring (H).
-
Install light bulbs into the sockets.
-
Thread finial (I) to fixture body.
NOTE: Do not overtighten otherwise glass could become damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>