VISUAL COMFORT CHC 5639 Clovis Grande Chandelier Instruction Manual
- June 12, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT CHC 5639 Clovis Grande Chandelier
Product Information
- Product Name: Clovis Grande Chandelier
- Item Number: CHC 5639
- Additional Information: Bulbs not included
Notice: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect s found, do not install. Retain all packaging material until installation is complete and approved.
Product Usage Instructions
- Carefully remove all parts from the box. Place on a clean, soft surface.
- Remove collar loop (D) from chain (F) by removing quick link (E).
- Install mounting plate (B) to the junction box and secure with mounting screws (C).
- Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.
- Install canopy (G) to collar loop (D) and secure with collar ring (H).
- Determine desired overall length, and amount of chain (F) needed. Shorten chain using chain pliers. (Keep extra chain)
- Attach chain (F) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E). NOTE: It is recommended to have a helper assist in supporting the fixture for steps 8.
- Attach chains (J) to hooks on metal frame (K) and hooks on fixture loop (I). See diagram 1 & 2.
- Thread fixture wire and ground wire through chain (F). NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. Separate two sides of molded wire, and strip insulation on each 5/8.
- Loosen collar ring (H) and let canopy (G) slip down chain (F) carefully.
- Twist all fixture wires together. Slip through the center hole of the collar.
Care Instructions:
Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
Item # CHC 5639
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
- Phillips Screwdriver
- Slotted Screwdriver
- Chain Pliers
- Slip Joint Pliers
- Measuring Tape
- Wire Cutters
- Wire Strippers
FEATURES
PERSONS REQUIRED:
- Two
ASSEMBLY INSTRUCTIONS
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove collar loop (D) from chain (F) by removing quick link (E).
-
Install mounting plate (B) to the junction box and secure with mounting screws (C).
-
Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.
-
Install canopy (G) to collar loop (D) and secure with collar ring (H).
-
Determine desired overall length, and amount of chain (F) needed. Shorten chain using chain pliers. (Keep extra chain)
-
Attach chain (F) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E).
NOTE : It is recommended to have a helper assist in supporting the fixture for steps 8. -
Attach chains (J) to hooks on metal frame (K) and hooks on fixture loop (I). See diagram 1 & 2.
-
Thread fixture wire and ground wire through chain (F).
NOTE : When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>