VISUAL COMFORT CHC 5638 Clovis Extra Large Chandelier Instruction Manual

VISUAL COMFORT CHC 5638 Clovis Extra Large Chandelier

Product Information

Item Number: CHC 5638

Notice: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect  s found, do not install. Retain all packaging material until installation is complete and approved.

Tools Required (Not Included):

• Phillips Screwdriver
• Slotted Screwdriver
• Slip Joint Pliers
• Measuring Tape
• Wire Strippers
• Chain Pliers
• Wire Cutters

Product Usage Instructions

1. Carefully remove all parts from the box and place them on a clean, soft surface.

2. Remove collar loop (D) from chain (F) by removing quick link (E).

3. Install the mounting plate (B) to the junction box and secure it with mounting screws (C).

4. Secure collar loop (D) to the mounting plate (B) using pliers to tighten the locknut.

5. Install the canopy (G) to the collar loop (D) and secure it with the collar ring (H).

6. Determine the desired overall length and the amount of chain (F) needed. Shorten the chain using chain pliers. Keep the extra
   chain.

7. Attach the chain (F) to the collar loop (D) and the fixture loop (I) using quick links (E). Secure the quick links (E).

8. Attach the chains (J) to the hooks on the metal frame (K) and the hooks on the fixture loop (I). Refer to diagram 1 & 2.

9. Thread the fixture wire and ground wire through the chain (F).
   Note: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, leaving enough to reach the junction box.

10. Separate two sides of the molded wire and strip insulation on each 5/8.

11. Loosen collar ring (H) and carefully let the canopy (G) slip down the chain (F).

12. Twist all fixture wires together and slip them through the center hole of collar loop (D). Note: Untwist wires and separate them to prepare for connection.

13. Wrap the fixture ground wire (bare copper) around the green grounding screw. Tighten. Continue the fixture ground wire and connect it to the supply ground wire (usually green or bare copper) using a wire nut (A). Note: It is imperative that the fixture is grounded.

14. Connect the fixture neutral wire (ribbed) to the supply neutral wire (usually white) using a wire nut (A). Connect the fixture hot wire (smooth with markings) to the supply hot wire (usually black) using a wire nut (A). Caution: Do not reverse the hot and neutral connections.

15. Make sure all wire connections are tight, then carefully tuck them into the junction box.

16. Install the canopy (G) to the collar loop (D) and secure it with the collar ring (H).

17. Install light bulbs into the sockets.

Item # CHC 5638

NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

FEATURES

TOOLS REQUIRED (NOT INCLUDED):

• Phillips Screwdriver
• Slip Joint Pliers
• Wire Strippers
• Slotted Screwdriver
• Measuring Tape
• Chain Pliers
• Wire Cutters

ASSEMBLY INSTRUCTIONS

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove collar loop (D) from chain (F) by removing quick link (E).

3. Install mounting plate (B) to the junction box and secure with mounting screws (C).

4. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.

5. Install canopy (G) to collar loop (D) and secure with collar ring (H).

6. Determine desired overall length, and amount of chain (F) needed. Shorten chain using chain pliers. (Keep extra chain)

7. Attach chain (F) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E).

8. . Attach chains (J) to hooks on metal frame (K) and hooks on fixture loop (I). See diagram 1 & 2.

9. Thread fixture wire and ground wire through chain (F).
   NOTE : When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

10. Separate two sides of molded wire, and strip insulation on each 5/8″.

11. Loosen collar ring (H) and let canopy (G) slip down chain (F) carefully.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>