HI-FOCUS HF-SH04-60W 4 Port POE Switch User Guide
- June 12, 2024
- HI-FOCUS
Table of Contents
HI-FOCUS HF-SH04-60W 4 Port POE Switch
Product Features
- Supports Power over Ethernet (PoE) cable devices such as wireless AP and IP cameras.
- Supports IEEE802.3af/at standard.
- Transmission distance of 250m, allowing flexible installation for wireless AP and surveillance projects.
- Supports upward port auto MDI/MDIX.
- Adopts storage forward switch system.
- Smart Power and minimum consumption to guarantee PD requirement.
- Provides power supply circuit protection function and protection for back-end devices.
- Automatically provides adaptive device.
- Fanless design for energy saving and environmental protection.
- No noise design to reduce environmental impact.
- Compact size design.
- Supports IEEE802.1Q VLAN and 4K VLANs.
- Supports loop circuit detection.
- Supports power saving function when port is disconnected.
Specifications
- Network Port Transfer Rate: Performance
- Network protocol and standard: N/A (not specified in the manual)
- Power pin LEDs indicator: Power
- Operating Temperature: N/A (not specified in the manual)
- Storage Temperature: N/A (not specified in the manual)
- Working Humidity: N/A (not specified in the manual)
- Storage Temperature: N/A (not specified in the manual)
- Dimensions (LxWxH): 125mm x 75mm x 27mm
- Weight: 0.5kg
Product Usage Instructions:
- Connect the PoE cable device (wireless AP or IP camera) to the HF-SH04-60W using an Ethernet cable.
- Ensure that the device you are connecting supports IEEE802.3af/at standard.
- Place the HF-SH04-60W within a transmission distance of 250m for flexible installation.
- Make sure to use the upward port auto MDI/MDIX feature for proper connectivity.
- Activate the storage forward switch system for efficient data transfer.
- Monitor the power consumption to meet PD requirements.
- Take advantage of the power supply circuit protection function to ensure device safety.
- If needed, enable the adaptive device functionality to optimize performance.
- Utilize the fanless design to save energy and contribute to environmental protection.
- Note that the noiseless design reduces environmental disturbances.
- Enjoy the compact size design for easy installation and space-saving.
- If VLANs are required, configure IEEE802.1Q VLAN and up to 4K VLANs.
- Enable loop circuit detection for enhanced network stability.
- To save power, activate the power saving function when a port is not connected.
HF-SH04-60W
Product Features
- Support Power over Ethernet cable device for example wireless AP and IP camera.
- Support IEEE802.3af/at standard .
- Transmission distance 250m, it can be flexible installation for wireless AP and surveillance project.
- Support upward port auto MDI/MDIX.
- Adopted storage forward switch system.
- Smart Power and minimum consumption, guarantee PD requirement.
- Provided with power supply circuit protection function and protection back-end device safety
- Automatically provide the adaptive device
- Fanless design realize saving energy and environment protection
- No noise design can reduce the affect for environment
- Compact size design
- Support IEEE802.1 Q VLAN and 4K VLANs
- Support loop circuit detection
- Support saving power function when port unconnection
Specifications
-
Network Port 4 10/100Mbps PoE RJ45 port(port 1~port 4) 2 10/100Mbps Non-POE RJ45 port(port 5~port6)
-
Transfer Rate 100Mbps full Duplex,10 or 100Mbps Half Duplex
-
Network interface:10BASE-T or 100BASE-TX Ethernet RJ-45 port
-
Performance Bandwidth:1.0Gbps (no block)
Network delay(100 to 100Mbps): Maximum 20 μs(using 64 byte packet)
MAC address capacity:1K
Frames filter and transfer rate 10M port maximum 14,800pps
100M port maximum 148,800pps -
Network protocol and standard IEEE 802.3i 10BASE-T IEEE 802.3u 100BASE-TX
IEEE 802.3x Flow Control
IEEE 802.3af/at Power over Ethernet -
Power pin 1/2(+),3/6(-)
-
LEDs indicator Power LINK/ACT,PoE
-
Power Total power:60W(PoE Port:1～4) (Each country use customized power plug)
ENVIRONMENTAL CHARACTERISTICS
- Operating Temperature 0°~45°C（32°~113°F）
- Storage Temperature -20℃~90℃（-4°~194°F）
- Working Humidity 10%~90% (Non-condensing)
- Storage Temperature 5%~90% (Non-condensing)
PHYSICAL CHARACTERISTICS
- Dimenions(LxWxH) 125mm x 75mm x 27mm
- Weight 0.5kg
An ISO 9001:2008 certified company
*Design and specification are subject to change without notice
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>