ADLER EUROPE AD 1191 Bluetooth Clock Speaker User Manual

June 12, 2024
ADLER EUROPE

ADLER EUROPE AD 1191 Bluetooth Clock Speaker

SAFETY CONDITIONS

IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

The warranty conditions are different, if the device is used for commercial purpose.

  1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
  2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
  3. The applicable voltage is 230V, ~50Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
  4. Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without  supervision.
  5. WARNING : This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
  6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
  7. Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
  8. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
  9. Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
  10. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
  11. Never use the product close to combustibles.
  12. Do not let cord hang over edge of counter or touch hot surfaces.
  13. Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
  14. In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
  15. Avoid getting the device wet.
  16. The device may only be wiped with a dry cloth. Do not use water or cleaning fluids.
  17. The device should be kept in a dry room.

Device Description (Clock speaker)

  1. DISPLAY
  2. STANDBY / Mode button
  3. Pause / Play button
  4. + Button
  5. – Button
  6. SD card slot
  7. Charging micro USB slot
  8. Playback USB slot

Before powering the device on. Remove all packing material and read the instruction manual carefully. Keep it for future reference.

Setting Up The Device

  1. Remove all the packing material from the device.
  2. Turn on the device by pressing and holding the Standby / Mode button (2)
  3. The device will turn on and enter Pairing mode. (If the device will not start pairing press the Standby / Mode button (2) until you enter Bluetooth mode.)
  4. Find the speaker on your playback device. It will show as “AD 1191”
  5. Press “Pair” on your playback device.
  6. The speaker will emit a sound noting the pairing is successful.
  7. The device is ready to use.

Charging

  1. Enter the Micro usb cable into the micro usb slot (7).
  2. The device will start charging. For a full charge it takes around 3 hours of charging.

Micro SD / USB playback

Please note the device supports files in .WAV and .MP3 format.

  1. Insert the card or pen drive into the correct slot. (6,7)
  2. The device will automatically enter the playback mode of the corresponding device.
  3. If you want to exit the USB / SD playback press the Standby/ Mode button (2) until you choose the desired mode. You can also remove the SD / USB from the device.

3.5 mm AUX cable Operation:

  1. The device comes with a special AUX 3,5 mm jack to micro usb cable.
  2. Insert the Jack side of the cable to your playback device.
  3. Insert the Micro usb side of the cable to the speaker.
  4. Press the Standby/ Mode button (2) until you choose the AUX mode.

Clock Setup:

  1. Turn on the device by pressing and holding the Standby/ Mode button (2)
  2. Press the Standby I Mode button (2) until you choose the Clock mode.
  3. Press the Play / Pause button (3) once to enter the time edit.
  4. Press the+ and – buttons (4,5) to increase and decrease the current setting.
  5. Press the Play/ Pause button (3) once to confirm your choice.
    (Please note that after the clock you will need to set up the alarm time.)

Alarm Setup

  1. Turn on the device by pressing and holding the Standby I Mode button (2)
  2. Press the Standby / Mode button (2) until you choose the Clock mode.
  3. Press the Play/ Pause button (3) once to enter the time edit.
  4. Press the + and – buttons (4,5) to increase and decrease the current setting.
  5. Set the desired time.
  6. The device will enter Alarm Mode.
  7. Press the + and – buttons (4,5) to increase and decrease the current setting.
  8. Press the Play/ Pause button (3) once to confirm your choice.
  9. After the setting the display will show “SAVE”
  10. The alarm is set.

Turning the alarm on and off:

  1. Turn on the device by pressing and holding the Standby/ Mode button (2)
  2. Press the Standby/ Mode button (2) until you choose the Clock mode.
  3. Press the Play/ Pause button (3) three times in rapid succession.
  4. The alarm icon in the lower right cornet will turn on.
  5. To turn off press the Play/ Pause button (3) three times in rapid succession again.
  6. The icon will disappear.

Indicator light status:

Blue light stable. The device is connected to a Bluetooth device/ Pen drive/ SD card.
Flashing blue light. Bluetooth is pairing / Low battery status.
Red light stable. Charging.
Red light Off. Speaker is fully charged.

Troubleshooting

Unsuccessful Bluetooth pairing: Restart the device and try again. Disable Bluetooth in your device and re- enable it.
Poor audio quality: Make sure the device is Bluetooth range.
Low or no volume: Increase the volume on the device and / or connect the device.
Undiscoverable in Bluetooth pairing: The device is paired with another phone. The speaker is not in Bluetooth mode.

Technical Details:

Power : 5V 1A
Output power : 2x 5W
Bluetooth : V 5.0
Battery : 1200mAh
Charging time : ~ 3 hours

To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.

Other Product


AFTER SALE SERVICE NOTICE

If you want to buy spare parts or make any complaints, please contact the seller who issued the receipt directly.

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals