MY PROJECT 300W MPSW 300 C3 Power Inverter Voltage Converter Instruction Manual

MY PROJECT 300W MPSW 300 C3 Power Inverter Voltage Converter

Product Information

Product Name: SPANNUNGSWANDLER 300W MPSW 300 C3
Product Type: Power Inverter
Languages: German (DE), English (GB), Romanian (RO), Moldavian (MD), Slovak (SK), Bulgarian (BG) Manual Pages: 5, 31, 56, 82, 107

Product Usage Instructions

1. Before using the product, unfold the page containing the illustrations and familiarize yourself with all the functions of the device.
2. Read the user manual carefully and follow all the safety instructions.
3. Check the package contents to ensure that you have received all the necessary items:
   • Spannungswandler (Power Inverter)
   • Cable with connection clamp (1x red 40 cm, 1x black 40 cm)
4. Familiarize yourself with the parts description of the product.
5. Review the technical specifications of the power inverter.
6. Follow the safety instructions provided in the manual.
7. Follow the specific safety instructions for proper operation and usage.
8. Follow the guidelines for setup and installation.
9. If using the power inverter in a vehicle, refer to the instructions for operating it in a vehicle.
10. Connect the power inverter to a power source according to the instructions provided.
11. If connecting to a car battery, follow the instructions for proper connection.
12. Pay attention to the low battery voltage signal.
13. If needed, replace the fuse according to the instructions.
14. Troubleshoot any issues following the troubleshooting guide.
15. Clean and maintain the power inverter as per the instructions.
16. Dispose of the product and packaging responsibly, following the environmental guidelines provided.
17. Review the warranty terms and conditions.
18. Follow the warranty and service handling instructions.
19. If required, contact customer service for further assistance.

Note: Please refer to the user manual for detailed instructions and safety guidelines in your preferred language.

Table of pictograms used

| Read the operating instructions!| |

Please note

| The car power inverter is only suitable for indoor operation.| | Warning:

Risk of electric shock! Danger to life!

| Observe warnings and safety instructions!| 50 Hz|

Frequency of 50 Hertz

|

Direct current

|

|

Don’t throw away – recycle!

|

Made from recycled material

| | Dispose of the device and packaging in an environmentally friendly manner!
|

Attention! Hot surface!

| V ~| Alternating voltage in volt
|

Packaging material – corrugated paper

|

|

You are legally obliged to place devices marked as such in a collection which is separate from unsorted municipal waste.

Disposal through household waste is prohibited.

|

Notebook

|

Mini stereo system

|

Camera

| |

Heater

|

Appliance class II

| |

Shaver

|

USB charger

| |

Cool box

POWER INVERTER 300W MPSW 300 C3

Introduction
Congratulations! You have purchased one of our high-quality products. Please familiarize yourself with the product before using it for the first time. To do this, please read through the following operating and safety instructions carefully.
KEEP OUT OF THE REACH OF CHILDREN!

Intended use
This car power inverter is designed to operate 230 V devices with maximum 300 W power draw or USB devices with maximum 1A current draw in the car with a 12 V connection. The car power inverter can either be connected to the cigarette lighter of the vehicle using the cigarette lighter adapter cable delivered with the device or connected directly to the battery using the adapter cable with clamps delivered with the device. If the car power inverter is connected directly to the battery using the adapter cable with clamps, then the car power inverter can only be used with a stationary vehicle. The manufacturer is not liable for any injury or damage resulting from improper use or incorrect operation. This car power inverter is not suitable for commercial use. Commercial use will void the warranty. The device has been developed for consumer use and is not suitable for use in a commercial or industrial environment. The product must only be started up initially by people who have been trained to do so. Keep these instructions in a safe place. Ensure you hand over all documentation when passing the product on to anyone else.

PLEASE NOTE! The output power depends on the temperature and voltage. The output voltage varies depending on the load and input voltage.

ATTENTION! Devices with sensitive electronics should not be operated using the car power inverter, as the output voltage may not be sufficiently constant for these devices. These devices could be damaged. If you have any doubts, please contact the manufacturer of the connected device.

Scope of delivery
PLEASE NOTE! After unpacking the product, please check that all of the package contents are present and that the car power inverter is in perfect condition. Do not use the device if it is defective.

1. car power inverter
2. cable with connecting clamp (1x red 40 cm, 1x black 40 cm)
3. cable with 12 V motor vehicle cigarette lighter plug (1.94 m)
4. set of operating instructions
5. replacement 20 A flat motor vehicle fuses
6. tongs for flat motor vehicle fuse

Parts description
PLEASE NOTE! After unpacking the product, please check that all of the package contents are present and that the device is in perfect condition. Do not use the device if it is defective.

To do this see Fig. A-D:

PLEASE NOTE! The use of the term ‘product’ or ‘device’ in the following text refers to the car power inverter described in these operating instructions.

Technical Specifications

Input:

Output:

2 and 4 USB connectors:

Fuse:

General data:

Operating humidity

(relative air humidity – no condensation):

| 0–80%

PLEASE NOTE! Changes to technical and visual aspects of the product may be made as part of future developments without notice. Accordingly, no warranty is offered for the physical dimensions, information and specifications in these operating instructions. The operating instructions cannot therefore be used as the basis for asserting a legal claim.

Safety instructions

PLEASE READ THROUGH THE OPERATING INSTRUCTIONS CAREFULLY BEFORE USE. THESE FORM PART OF THE PRODUCT AND MUST BE AVAILABLE AT ALL TIMES!

This section covers the basic safety instructions applicable when working with the device.

Personal safety!

• This device may be used by children aged 16 years and older, and by persons with reduced physical, sensory or mental capacities, or a lack of experience and knowledge, if they are supervised or have been instructed in how to use the device safely and understand the dangers that may arise when using it. Do not allow children to play with the device.

• Cleaning and day-to-day maintenance must not be performed by children without supervision.
  Children must be supervised to ensure that they do not play with the device.

• Keep the device away from people – especially children – and household pets.

• Within the working area, the user is responsible for any damage or injury to third parties that was caused by the use of the device.

• During operation, never point the device at yourself or other individuals, and keep the device well way from your ears and eyes. There is a risk of injury!

• Do not leave the device running unattended.

• Keep the device in a dry location and out of the reach of children.

• In order to avoid dangers, before using or cleaning the car power inverter each time, unplug it from the car’s electrical system or remove the connecting clamps from the car battery.

• Only connect the car power inverter to the car battery when the engine is switched off! There is a risk of injury through moving parts!

• The car power inverter must always be accessible so that the device can be quickly disconnected from the battery in case of emergency.

This helps prevent device damage and possible personal injuries that could result from it:
Risk of electric shock!

• Only connect the car power inverter to a 12 V car battery/electrical system. Connecting to a 24 V voltage can damage the device.

• When connecting the car power inverter using the 12 V motor vehicle cigarette lighter plug make sure that the polarity of the motor vehicle cigarette lighter plug matches the polarity of the socket for the car’s electrical system. The socket of the electrical system must have internal positive polarity, i.e. the positive terminal of a vehicle battery must not be connected to the chassis of the vehicle.

• Before connecting the inverter, check that the socket for the electrical system is sufficiently fused.
  This fuse protection must not be bypassed or altered, under any circumstances.

• Only use the connection cable delivered with the product.

• You must not open or repair the housing of the device. If you do, then the safety of the device is no longer assured and the guarantee will be null and void.

• The device is only suitable for use indoors. Fire hazard!

• Do not use the device near hot surfaces.

• Do not position the device in places which are exposed to direct sunlight. Otherwise it could over-heat and be damaged beyond repair. Do not use the device in a vehicle which is parked in the sun.

• Never leave the device unattended when it is being used.

• Do not cover the ventilation slots of the fan when the device is switched on.

• Do not place any open ignition sources such as, for example, candles on the device.

• Both connection cables can get warm under high loading.

• Due to the high transfer resistances, using the cable with 12 V motor vehicle cigarette lighter plug can lead to the plug connection heating up. Therefore when working with high loads, always use the connection cable with the connecting clamps.

Notes on disconnecting from the power supply!

• The On/Off switch of this device does not completely disconnect the device from the electrical system or battery. When the motor vehicle cigarette lighter plug is connected, the device takes power. In order to disconnect the device completely from the car’s electrical system, the 12 V motor vehicle cigarette lighter plug must be unplugged from
  the socket of the electrical system/the connecting clamps must be removed from the car battery.

Working with the device

• Before setup or first use, check the device for any damage and do not use unless in perfect working order.

• Do not expose the device to rain or wet weather. Do not let the device come into contact with water. Do not immerse the device in water. There is a risk of electric shock!

• Keep all openings of the device free during operation. Do not block the openings with your hands or fingers, and do not cover the device. There is a risk of over-heating!

• In hot weather, do not leave the device in a car. This could permanently damage the device.

• The device becomes warm during use. There is a risk of burn injuries from touching the hot surfaces.

• Take care to ensure that sand, dust and other small foreign objects cannot enter the air inlet or air outlet openings.

• Do not operate the device near to flammable liquids or gases. Do not use the device to draw in hot fumes. Failure to do so risks causing a fire or explosion!

• Switch the device off and disconnect the device from the voltage supply:

  • when you are not using the device;
  • if you are leaving the device unsupervised;
  • if you are doing cleaning work;
  • if the connection cable is damaged;
  • if foreign objects have got into the device or you notice unusual noises.

• Only use the accessories supplied and recommended by the manufacturer.

• Do not disassemble or modify the device.
  This device must only be repaired by a maintenance technician.

• Do not store in places where the temperature can exceed 65 °C.

• Only use in an ambient temperature between 5 °C and 40 °C.

• Only use the adapter cable as supplied with the device.
  CAUTION! How to avoid accidents and injuries from electric shock:
  Electrical safety:

• Do not use the device if the switch cannot be switched on and off. Arrange for damaged switches to be replaced.

• Do not carry the device by the cable.
  Do not unplug the plug from the socket by pulling on the cable. Protect the cable from heat, oil and sharp edges.

• If the cable of the device is damaged, disconnect it from the voltage supply immediately.

Specific safety instructions

• A slightly higher operating temperature is absolutely normal and not a malfunction.
• Protect the car power inverter from moisture and high temperatures, including fires.
• Store the car power inverter in a dry place and protect the device from moisture and corrosion.
• Do not drop the device.

Using the device
Take all parts from the packaging and check whether the car power inverter 1 or parts show any damage. If this is the case, do not use the car power inverter. Contact the manufacturer via the indicated service address. Remove all protective films and other transport packaging. Check that the delivery is complete.
ATTENTION! Do not allow small children to play with the packaging film. There is a risk of suffocation!

Instructions for operation
For continuous operation of devices using the car power inverter 1 the socket for the electrical system must have a voltage between 10.5 V and 14.8 V. Before connecting the car power inverter 1 , check whether the voltage supply provides sufficient power for operation. The power required for operation can be calculated as follows:

Current draw (A) = ( Operating output of the load (W)
Efficiency (η)
Input voltage (V)

Example:
300 W
0.75 = 33.3 A
12 V

The voltage supply should provide at least 33.3 A for a continuous load of 300 W.

PLEASE NOTE!
12 V sockets for the electrical system provide max. 10 A, therefore in this example, the car power inverter 1 must be connected directly to the car battery using the connecting clamps. This is the only way to ensure continuous output of 300 W.

ATTENTION! Never connect the car power inverter 1 to a 24 V electrical system. Otherwise the device will be damaged. The device must only be connected to a voltage supply with a nominal voltage of 12 V.

Install and secure

• The car power inverter 1 should be positioned on a flat, even surface.
  Make sure that there is at least 1 cm free space around the car power inverter 1 for air circulation.

• A gap of 50 cm must be maintained behind the ventilation slots of the fan 14.

• There are holes 15 in the plastic base of the car power inverter 1 so that it can mounted securely in a vehicle. Using suitable screws, the car power inverter 1 can be securely mounted. When doing this make sure you maintain the space for air circulation as stated above.

• Due to vehicle-specific factors, it is not possible to include fittings which fit all situations.

• If you are unsure, contact your motor vehicle garage.

Operation in a vehicle
If you are operating the car power inverter 1 in a vehicle, make sure that the installation does not impair your driving. You should therefore always lay the cable so that it does not touch any moving parts inside the vehicle and does not obstruct your vision.

PLEASE NOTE! The car power inverter 1 can also be operated with the engine switched off. But please note that the car power inverter 1 may possibly not work when you are starting up the engine.

Connecting to a voltage supply

ATTENTION!
Before connecting the car power inverter 1 to a voltage supply, make sure that the On/Off switch 5 of the device is in the “0” (OFF) position. You can connect the car power inverter 1 using the 12 V vehicle cigarette lighter plug 12 to the socket for the 12 V car’s electrical system or clamp the cables with the 10 and 11 connecting clamps directly to the car battery.

Connecting to a 12 V motor vehicle cigarette lighter socket

• Undo the red nut 16 on the car power inverter 1 . Guide the red fork eyelet of  the cable with 12 V motor vehicle cigarette lighter plug 12 with the opening over the screw connector 7 (see Fig. 1). Make sure that the washer is positioned between the fork eyelet and the nut 16.
• Tighten the red nut 16 such that the fork eyelet is held in place.
• Undo the black nut 17 on the car power inverter 1 . Guide the black fork eyelet of the cable with 12 V motor vehicle cigarette lighter plug 12 with the opening over the 12 V screw connector 8 (see Fig. 1). Make sure that the washer is positioned between the fork eyelet and the nut 17.
• Tighten the black nut 17 such that the fork eyelet is held in place.
• Plug the cable with 12 V motor vehicle cigarette lighter plug 12 into a motor vehicle cigarette lighter socket.

PLEASE NOTE! Due to the high transfer resistances, using the cable with 12 V motor vehicle cigarette lighter plug 12 can lead to the plug connection heating up. Therefore when working with high loads, use the connection cable with the 10 and 11 connecting clamps.

Connecting to a car battery

• Undo the red nut 16 on the car power inverter 1 . Guide the red fork eyelet of  the cable with the red connecting clamp 10 over the 12 V screw connector 7 (see Fig. 1). Make sure that the washer is positioned between the fork eyelet and the nut 16.
• Tighten the red nut 16 such that the fork eyelet is held in place.
• Undo the black nut 17 on the car power inverter 1 . Guide the black fork eyelet of the cable with the black connecting clamp 11 over the screw connector 8 (see Fig. 1). Make sure that the washer is positioned between the fork eyelet and the nut 17.
• Tighten the black nut 17 such that the fork eyelet is held in place.
• First connect the red clamp to the positive terminal of the car battery and then connect the black clamp to the negative terminal of the car battery.

Connecting and operating a load/device

• ATTENTION! Before connecting a load/device to the car power inverter 1 , make sure that the On/Off switch 5 of the device is in the “0” (OFF) position. Make sure that the output of the connected load/connected device does not exceed the maximum continuous output of the car power inverter 1 .
• ATTENTION! Do not switch on the load/device to be operated yet! Connect the plug of the load to be connected/device to be operated to the 230 V socket 6 of the car power inverter 1 .
• Switch the car power inverter 1 on, by moving the On/Off switch 5 to the “1” (ON) position. You will hear a short beep and the overload display 3a (red) lights up briefly. After that the operating LED 3b (green) lights up, if the car power inverter 1 is properly connected to a charged battery.
• Now switch on the load/device to be operated.

PLEASE NOTE! If you hear a beep and the overload display 3a lights up red, the input voltage is too low, or output of the load/device connected to the car power inverter 1 is too high

Instructions for operating devices

General notes:
Information about the power consumption in Ampere (A) or the power draw in Watt (W) is usually shown on the rating plate of devices.
Before using the device, please make sure that the maximum current draw is not higher than 1.30A and the maximum continuous output is not more than 300 W.

• Loads with a high internal resistance can be operated very effectively using the car power inverter 1 , whereas loads with a low internal resistance, such as, for example, heating and cooking devices, generally have a power draw in Watt which is too high.

• Inductive loads such as, for example, televisions or stereo devices (devices with a coil or a transformer) often require a start-up current which is many times higher than resistive loads with the same given power draw in Watt. When switching on, televisions require a power draw which is many times higher than the value given on the rating plate. Because of this you may need to switch the car power inverter 1 on and off several times, in order to be able to switch a television on.

• If you have any doubts, please contact the manufacturer of the connected device.

• Televisions:
  The car power inverter 1 is screened and outputs a modified sine wave. However if reception from television channels is extremely weak, this can lead to interference or picture distortion. In this case, position the car power inverter 1 as far from the television, aerial cable and aerial as possible. Align the car power inverter 1 , television, aerial cable and aerial to one another, until the reception improves. If possible, use a high-quality, screened aerial cable.

• Audio systems:
  Some audio/video systems emit a humming noise through the speaker when they are operated using the car power inverter 1 . This is due to the fact that these devices cannot filter the modified sine wave of the car power inverter 1 and is not a defect of the car power inverter  1

Signal if the battery voltage is low

• If the battery voltage sinks below 10.5 V, the car power inverter switches off 1 and the overload display 3a lights up red. A warning beep sounds.

Charging a USB device
ATTENTION! Before connection, make sure that the current draw of the USB device is not higher than 1 A. For more detailed information, please refer to the operating instructions for your USB device.

• Plug the USB plug of the USB device to the USB A connector 4 or the USB C connector 2 of the car power inverter 1 .
• If necessary, switch the USB device on.

PLEASE NOTE! The 230 V socket 6 and the USB connection 2 / 4 can be used at the same time.

Replacing the fuse
DANGER TO LIFE THROUGH ELECTRIC SHOCK! Before replacing the fuse, disconnect the car power inverter 1 from the power supply. Also remove any device connected to the car power inverter

1. Replace the fuse with one of equal value with the same cut-off characteristics (20 A), as given in the technical specifications or with one of the enclosed flat motor vehicle fuses 22.
   ATTENTION! You must not use a fuse with a different value! Before switching the car power inverter 1 back on, ascertain why the fuse tripped.

In order to replace the 20 A flat motor vehicle fuse 13, proceed as follows:

• Pull the flat motor vehicle fuse 13 out of the fuse holder 9 . You can pull the fuse out easily by using the enclosed tongs 23 for the flat motor vehicle fuse.
• Insert a new fuse of equal value.

In order to replace the 10 A glass fuse 19 in the cigarette lighter plug 18, proceed as follows:

• Unscrew the fuse screw plug 21. The fuse is located below this plug.
• When doing this, make sure you do not lose the loosely inserted contact pin
• Remove the defective 10 A glass fuse 19.
• Insert a new 10 A glass fuse of equal value 19.
• Insert the contact pin 20 into the fuse screw plug 21 plug 21 back onto the 12 V cigarette lighter plug 18.

Troubleshooting

1 is overloaded.

| Reduce the load until it no longer exceeds the

maximum load given in the technical specifications.

The input voltage is below 10.5 V.| Keep the input voltage  of the car power inverter over

10.5 V, in order to maintain an output voltage.

Low output voltage| The input voltage is below 12 V.| Keep the input voltage of the car power inverter over 12 V, in order to maintain a constant output voltage.
The signal for low battery voltage sounds repeatedly.| The battery is defective.| Replace the battery.
| Insufficient voltage supply or power supply.| Check the condition of the socket of the car’s electrical system and the 12 V vehicle cigarette lighter plug 12 and clean these if required.
No output power| The car power inverter 1 is not completely warmed up due to low environmental temperatures (e.g. at temperatures below 10 °C in the winter).| Switch the car power inverter 1 on and back off, until the device connected to the car power inverter 1 is supplied with power.

Repeat this procedure in order to be able to switch the device on.

No output power| The ignition must be switched on in order for the socket for the car’s electrical system to have power.| Switch the motor vehicle ignition on or move to the “1” (ON) position.
| The car power inverter

1 is overloaded.

| Reduce the load until it no longer exceeds the

maximum load given in the technical specifications.

| The car power inverter

1 has overheated.

| Wait until the device has cooled off. Make sure that there is sufficient ventilation clearance. Make sure that the connected  load  does not continuously   exceed the maximum loading, in order to avoid the device overheating again.
| The fuse in the device| Replace the fuse, as
| has blown.| described in the “Replacing
| | the fuses” chapter.
| | Make sure that the car
| | power inverter 1 is
| | connected to the power
| | supply using the right
| | polarity.

Cleaning and maintenance

ATTENTION!
The device must not come into contact with water or be placed in water. There is a risk of injury due to electric shock if moisture enters the device.

• Before cleaning, always disconnect the car power inverter 1 from the motor vehicle cigarette lighter socket/remove the connecting clamps from the car battery. Also remove any device connected to the car power inverter 1 .
• Clean the surface of the housing and accessories with a slightly damp cloth. Never use petrol, solvents or cleaners as these can corrode the surface of the device! If the ventilation slots are dusty, clean them with a soft brush.

Information about recycling and disposal
DO NOT DISPOSE OF ELECTRICAL TOOLS IN HOUSEHOLD WASTE! DON’T THROW AWAY – RECYCLE!
According to European Directive 2012/19/EU, used electrical devices must be collected separately for environmentally compatible recycling or recovery. Electrical and electronic devices which have become waste are called old devices. Owners of old devices are obliged to place them in a collection which is separate from unsorted municipal waste. Owners of old devices have old batteries and old rechargeable battery packs, which are not enclosed by the old device, as well as bulbs which must be separated from the device before
it is handed in at a collection point. This does not apply if the old devices are handed in to public waste disposal authorities and they are separated from other old devices there for the purposes of preparation for recycling. If you are unsure, please contact an independent specialist. Owners of old devices from private  households can hand these in to collection points for public waste disposal authorities or collection points which have been set up by manufacturers or distributors in line with the ElektroG (German disposal of electrical equipment act). The disposal of defective devices which you have sent in will be carried out free of charge. You can also return the old device to your Kaufland branch, free of charge. As the end user, it is your responsibility to delete any personal information on the old devices to be disposed of.

Please return this device, accessories and packaging to your local recycling depot.

This device is marked in accordance with the 2012/19/EU directive on old electronic and electrical devices (WEEE). The symbol of the “crossed out dustbin” means that you are legally obliged to place these devices in a collection which is separate from unsorted municipal waste. Disposal through household waste is prohibited. Batteries containing harmful substances are labelled with the adjacent symbol, which indicates the prohibition on disposal in household waste. The abbreviations for the relevant heavy metals are:
Cd = cadmium, Hg = mercury, Pb = lead.

Take used batteries to a waste management company in your city or community or return them to your dealer. This satisfies your legal obligations while also making an important contribution to protecting the environment.

Please note the marking on the different packaging materials and separate them as necessary. The packaging materials are marked with abbreviations (a) and digits (b) with the following definitions: 1–7: Plastics, 20–22: Paper and cardboard, 80–98: Composite materials.

Original EC Declaration of Conformity

We,
C. M. C. GmbH
Responsible for documentation:
Dr. Christian Weyler
Katharina-Loth-Str. 15
66386 St. Ingbert
GERMANY
hereby take sole responsibility for declaring that the product

Power inverter

• IAN: 409759_2207
• Art. no.: 2538
• Year of manufacture: 2023/11
• Model: MPSW 300 C3

meets the basic safety requirements as specified in the European Directives

Electromagnetic Compatibility:
(2014/30/EU)

Low Voltage Directive:
(2014/35/EU)

RoHS Directive:
(2011/65/EU+2015/863/EU)

and the amendments to these Directives.

The object of the declaration described above meets the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

This conformity assessment is based on the following harmonized standards:

• EN 62368-1:2014/A11:2017
• EN 50498:2011

St. Ingbert, 01.08.2022

Dr. Christian Weyler – Quality Assurance –

Warranty and service information

Warranty from Creative Marketing & Consulting GmbH

Dear Customer,
The warranty for this equipment is 3 years from the date of purchase. In the event of product defects, you have legal rights against the retailer of this product. Your statutory rights are not affected in any way by our warranty conditions, which are described below.

Warranty conditions
The warranty period begins on the date of purchase. Please retain the original sales receipt.

This document is required as your proof of purchase.
Should this product show any defect in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our discretion – free of charge. This warranty service requires that you retain proof of purchase (sales receipt) for the defective device for the three year period and that you briefly explain in writing what the fault entails and when it occurred.
If the defect is covered by our warranty, we will repair and return your product or send you a replacement. The original warranty period is not extended when a device is repair or replaced.

Warranty period and statutory claims for defects
The warranty period is not extended by the guarantee. This also applies to replaced and repaired parts. Any damages or defects detected at the time of purchase must be reported immediately after unpacking. Any incidental repairs after the warranty period are subject to a fee.

Extent of warranty
This device has been manufactured according to strict quality guidelines and carefully inspected before delivery.
The warranty applies to material and manufacturing defects only. This warranty does not extend to product parts, which are subject to normal wear and tear and can thus be regarded as consumable parts, or for damages to fragile parts, e.g. switches, rechargeable batteries or parts made from glass.
This warranty is voided if the product becomes damaged or is improperly used or maintained. For proper use of the product, all of the instructions given in the operating instructions must be followed precisely. If the operating instructions advise you or warn you against certain uses or actions, these must be avoided in all circumstances.
The product is for consumer use only and is not intended for commercial or trade use. The warranty becomes void in the event of misuse and improper use, use of force, and any work on the device that has not been carried out by our authorized service branch.

Processing of warranty claims
To ensure prompt processing of your claim, please follow the instructions given below.
Please retain proof of purchase and the article number (e.g. IAN) for all inquiries. The product number can be found on the type plate, an engraving, the cover page of your instructions (bottom left), or the sticker on the back or underside of the device.
In the event of malfunctions or other defects, please first contact our service department below by phone or email. If your product is found to be defective, you can then send your product with proof of purchase (till receipt) and a statement describing what the fault involves and when it occurred free of charge to the service address given.

PLEASE NOTE : You can download this handbook and many more at www.kaufland.com/manual.
With this QR code you can gain immediate access to our international website (www.kaufland.com/manual) By clicking on the appropriate country you can gain access to the national overview of our handbooks. By entering the article number (IAN) 409759 you can open the operating instructions.

Service
How to contact us:
GB
Name: C. M. C. GmbH
Website: www.cmc-creative.de
E-mail: service.gb@cmc-creative.de
Phone: 0-808-189-0652
Registered office: Germany
IAN 409759_2207
Please note that the following address is not a service address.
Please first contact the service point given above.

Address :
C. M. C. GmbH
Katharina-Loth-Str. 15
66386 St. Ingbert
GERMANY
Ordering spare parts: www.ersatzteile.cmc-creative.de

References

• Creative.DE - creative Produkte und Dienstleistungens
• manual | Kaufland
• C.M.C Creative Marketing & Consulting GmbH | Home
• Parkside Spareparts
• manual | Kaufland

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>