Lumens LC-RC01 Remote Control Panel User Manual

Lumens LC-RC01 Remote Control Panel

Product Information

The LC-RC01 is a remote control panel designed for use with Lumens products. It features a power adapter, USB control connector, DC power input interface, and RJ-45 network port. The control panel is used for connecting to the recording system and the USB port on the recording system. It also connects to the power cord originally connected to the recording system and the RJ45 network port of the control box. The control box has a USB 2.0 port, function buttons, and an RJ-45 port. The LC-RC01E is designed for use in Europe, while the LC-RC01U is designed for use in North America.

Package Contents

Product Overview

LC-RC01 adapter

Remark> **LC200 needs to connect to the USB port “below”
3.| DC power input interface| Connecting the power cord originally connected to the recording system to this power input port
4.| RJ-45 network port| Connecting to RJ45 network port of the control box

LC-RC01 control box

Size

Instruction for installation

1. Secure the adapter to the media processor with screws and connect the DC power and USB.
2. Use the CAT5e network cable for connection (the length shall not exceed 30 meters).
3. Pass a cable tie through the mounting hole to secure the network cable onto the LC-RC01 control box.
4. Install the control box on the wall.

Function Description

Button function description

LED Indicator Description

disk

Press again to cancel back up

Red light flickering 6 times| Error in writing the data into the USB flash disk
STREAM| N| Unpowered
Blue light| Powered, but Push is not enabled Press again to enable Push
Red light| Pushing; press again to stop Push
Record| N| Unpowered
Blue light| Powered, but the record is not enabled Press again to enable the record
Red light| Recording; press again to stop record
Red light flickering 6 times| Error or failure during recording

Web Page Function

1. Remote control panel connection
   Log in to the web page, Click [System] > [Remote Control Panel] to check the connection status between the recording system and LC-RC01

   • Connected
   • Disconnected

2. Macro Settings
   Log in to the web page, Click [Scenes] > [Macro]

   • LC-RC01 [1~3] buttons correspond to Macro [1~3] Settings
     NO.| Function Descriptions
     ---|---
     1| Select a scene to be set. Each supports up to 9 sets of scene. < Remark> If the layout of the scene needs to be change, please refer to the user manual of recording system
     2| Set/Cancel [Camera Preset Position]. Each supports up to 9 sets of camera preset position selection.

Troubleshooting

This chapter describes problems you may encounter while using LC-RC01. If you have questions, please refer to related chapters and follow all the suggested solutions. If the problem still occurred, please contact your distributor or the service center.

refer to Chapter 3 Instruction for installation to ensure that USB cable is inserted into the “below” USB port of LC200
2| No indicator is shown on the LC-RC01 panel| Please refer to Chapter 3 Instruction for installation to ensure that the control box properly connects to the adapter by the CAT5e network cable

Safety Instructions

Always follow these safety instructions when setting up and using the LC-RC01 Remote Control Panel:

1. Operation
2. Please use the product in the recommended operating environment, away from water or source of heat
3. Do not place the product on a tilted or unstable trolley, stand or table.
4. Please clean the dust on the power plug prior to usage. Do not insert the product’s power plug into a multiplug to prevent sparks or a fire.
5. Do not block the slots and openings in the case of the product. They provide ventilation and prevent the product from overheating.
6. Do not open or remove covers, otherwise it may expose you to dangerous voltages and other hazards. Refer all servicing to licensed service personnel.
7. Unplug the product from the wall outlet and refer servicing to licensed service personnel when the following situations happen:

  * If the power cords are damaged or frayed.  

If liquid is spilled into the product or the product has been exposed to rain or water.

2. Installation
3. For security considerations, please make sure the standard mount you use is in line with UL or CE safety approbations and installed by technician personnel approved by agents.
4. Storage
5. Do not place the product where the cord can be stepped on as this may result in fraying or damage to the lead or the plug.
6. Unplug this product during thunderstorms or if it is not going to be used for an extended period.
7. Do not place this product or accessories on top of vibrating equipment or heated objects.
8. Cleaning
9. Disconnect all the cables prior to cleaning and wipe the surface with a dry cloth. Do not use alcohol or volatile solvents for cleaning.
10. Batteries (for products or accessories with batteries)
11. When replacing batteries, please only use similar or the same type of batteries
12. When disposing of batteries or products, please adhere to the relevant instructions in your country or region for disposing of batteries or products

Precautions

FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC Warning
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.

EN55032 CE Warning
Operation of this equipment in a residential environment could cause radio interference. Warning: Operation of this equipment in a residential environment may cause radio interference

Copyright Information

• Copyrights © Lumens Digital Optics Inc. All rights reserved. Lumens is a trademark that is currently being registered by Lumens Digital Optics Inc. Copying, reproducing or transmitting this file is not allowed if a license is not provided by Lumens Digital Optics
• Inc. unless copying this file is for the purpose of backup after purchasing this product.
• In order to keep improving the product, the information in this file is subject to change without prior notice.
• To fully explain or describe how this product should be used, this manual may refer to names of other products orcompanies without any intention of infringement.
• Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any possible technological, editorial errors or omission s, nor responsible for any incidental or related damages arising from providing this file, using, or operating this product.

To download the latest version of Quick Start Guide, multilingual user manual, software, or driver, etc., please visit Lumens https://www.MyLumens.com/support

References

• Download | Lumens

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>