UREVO URTM023 Strol 1E 2 In 1 Under Desk Treadmill User Manual

June 12, 2024
UREVO

URTM023 Strol 1E 2 In 1 Under Desk Treadmill

URTM023-Strol-1E-2 In-1-Under-Desk-Treadmill-product

Product Information

  • Model: URTM023
  • Product Name: Strol 1E 2-in-1 Under Desk Treadmill

Product Usage Instructions
To ensure safe and proper usage of the Strol 1E 2-in-1 Under desk Treadmill, please follow the instructions below:

Important Safety Instructions
Refer to page 3 of the user manual for detailed safety instructions.

Product & Accessories
Refer to page 5 of the user manual for information about the product and included accessories.

Specification
Refer to page 6 of the user manual for detailed specifications of the Strol 1E 2-in-1 Under Desk Treadmill.

Product Introduction
Refer to page 7 of the user manual for an introduction to the Strol 1E 2-in-1 Under Desk Treadmill.

How to Use
Refer to page 8 of the user manual for step-by-step instructions on how to use the Strol 1E 2-in-1 Under Desk Treadmill.

Operation
Refer to page 11 of the user manual for information on operating the Strol 1E 2-in-1 Under Desk Treadmill.

Care & Maintenance
Refer to page 13 of the user manual for instructions on how to care for and maintain the Strol 1E 2-in-1 Under Desk Treadmill.

Error Code
Refer to page 15 of the user manual for a list of error codes and troubleshooting steps.

Troubleshooting
Refer to page 16 of the user manual for troubleshooting tips and solutions.

Warranty
Refer to page 17 of the user manual for information about the warranty coverage for the Strol 1E 2-in-1 Under Desk Treadmill. For visual instructions, you can also watch the YouTube video provided.
Note: The Strol 1E 2-in-1 Under desk Treadmill requires a CR2025 3V battery for operation. Please ensure the battery is properly installed. Use the buttons labeled “A” and “B” to control the treadmill. Press “FREE RUN” to start the treadmill in free-run mode. Press “PAUSE” to pause the treadmill, and press “STOP” to stop the treadmill.

CUSTOMER SERVICE

IMPORTANT: FOR UREVO ONLY
For damaged or defective products, questions, replacement parts, or any other service support, please contact our customer service department by the below methods:  services@urevosports.com

  • Response Time: 24-48 hours
  • Emailing us with the Order ID will be the best method to receive a response during peak business hours.
  • Website: www.urevosports.com
  • US Support Hotline: (1)844-998-2473
  • Hours of Operation: Monday – Friday: 9 AM – 12 PM; 1 PM – 6 PM (PST)

PLEASE DO NOT RETURN THIS PRODUCT WITHOUT ASKING OUR CUSTOMER SERVICE FIRST. SCAN THIS QR CORD TO GET THE PRODUCT INSTALLED OR MAINTENANCE VIDEOS

DANGER – To reduce the risk of electric shock: Always unplug this treadmill from the electrical outlet immediately after using and before cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

  1. A treadmill should never be left unattended or plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.
  2. Do not operate under a blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
  3. Close supervision is necessary when this treadmill is used by, on, or near children, invalids, or disabled persons.
  4. Use this treadmill only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
  5. Never operate this treadmill if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the treadmill to a service center for examination and repair.
  6. Do not carry this treadmill by supply cord or use the cord as a handle.
  7. Keep the cord away from heated surfaces.
  8. Never operate the treadmill with the air openings blocked. Keep the air openings free of lint, hair, and the like.
  9. Never drop or insert any object into any opening.
  10. Do not use outdoors.
  11. Do not operate where aerosol (spray) products are being used or where oxygen is being administered 12. Caution – To reduce the risk of injury from moving parts – Unplug before servicing.
  12.  Warning – To reduce the risk of Electric shock – Unplug before cleaning or servicing.
  13. Warning – Risk of personal injury – Keep children under the age of 13 away from the machine.
  14. To disconnect, turn all controls to the position, then remove the plug from the outlet.
  15. Connect this treadmill to a proper outlet only. See grounding instructions.
  16. This treadmill is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the treadmill by a person responsible for their safety. Keep children under the age of 13 away from this machine.
  17. The maximum weight capacity for this product is 265 kg/120kg. DO

NOT EXCEED MAXIMUM WEIGHT CAPACITY. SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electricity and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not
modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Accessories

UREVO-URTM023-Strol-1E-2-In-1-Under-Desk-Treadmill-
FIG-2

SPECIFICATION

Product configuration| Detailed parameters| Product configuration| Detailed parameters
---|---|---|---

Product dimension (Folded)

|

135 x 62 x 12.5 cm

|

Product dimension (Unfolded)

|

127 x 62 x 108 cm

53.2 x 24.4 x 5.0 inch

|

50.2 x 24.4 x 42.5 inch

Running area

|

40x 105 cm

|

Maximum speed

|

7.6 mph

15.7 x 41.3 inch

Gross weight

|

29.5 KG

|

Minimum speed

|

0.6 mph

65 Lbs

Net weight

|

24.8 KG

|

Rate voltage

|

110-120V~

54.7 Lbs

Maximum load

|

120 KG

|

Peak housepower

|

2.5 Hp

265 Lbs

|

Suggested age

|

14-60 years old

PRODUCT INTRODUCTION

UREVO-URTM023-Strol-1E-2-In-1-Under-Desk-Treadmill-
FIG-3UREVO-URTM023-Strol-1E-2-In-1
-Under-Desk-Treadmill-FIG-4
HOW TO USE
Unfolded To Run (Speed range: 0.6 – 7 .6mph)

  1. Unbox to take out the treadmill with the related accessories, then place the treadmill on flat ground.
  2. Foot pedal to release upright and grab the tip of upright.
  3. Lifting upright up till the end of the position. Hearing a “Click” means the upright is locked.UREVO-URTM023-Strol-1E-2-In-1-Under-Desk-Treadmill-FIG-7

Folded To Walk (Speed range: 0.6 – 4.0mph)

  1. Detach the tablet mount.
  2. Foot pedal to fold down handlebar sub-assembly.
  3. Enjoy walking exercises with remote control.

Safety Key
In any emergency that occurs, the treadmill stops automatically and shows “—” when the safety key is pulled out from the console.
NOTE : Find the clip (A) onto the waistband of your clothes, and another key (B) magnetic attracted under the console.

Transportation

  1. If transportation needs, please unplug the power cord and tablet mount before lifting the terminal of the treadmill.
  2. Easy to transport treadmill with bottom transportation wheel assists, like as wheelbarrow.

NOTE: Before moving and storage, please make sure the power switch into off and the power cord is unplugged.

OPERATION
Unfolded Usage Scenarios

Dial diaplay work only, all of work modes selection are operated with dial.

UREVO-URTM023-Strol-1E-2-In-1-Under-Desk-Treadmill-
FIG-13

Dial Function Menu
Dial operation and illumination introduction

  • Push dial to light on diaplay, you will see the Welcome animation that Urevo logo illuminated gradually.
  • 5 optional work modes choose with dial (CW or CCW roate), default setting is Free run.
    Work Mode| Function
    ---|---

Free run

| Freely choose your favorite speed and run, your cumulative workout data are alternate illuminated on dial display.

HIITEasy

| Offer 2.17 miles run in 24’20” to gain Easy HIIT effect and estimated 620Kcal burn.

HIITMedium

| Offer 2.92 miles run in a half hour to achieve Deep HIIT effect and estimated 834Kcal burn.

HIIT Hard

|

Offer 1.48 miles run in 17′ and estimated 422Kcal burn.

Note: The variable speed of all stroke is programmed in product. It’s not appliable to change speed by manual. You’re able to tracking the state of motion with progress bars, where indicated on dial display

Target run

| Setting your desired workout objective and run (configurable factors: Time; Distance and Calories), manual speed change is appliable.

Pause &Stop

Short push dial in use. Workout data will be erased and display light off in case Pause duration over than 10 minutes. Hold push (1-2 seconds) dial in use or finished exercise. Lack safety key in unfolded usage scenarios. But it’s not mandatory required to attach safety key in folded usage scenarios.

Folded Usage Scenarios
By-pass dial, all of operation are processed by remote control and illuminated at numeric display.

Display Screen
As you walk on the treadmill, the display can show the following workout information:

UREVO-URTM023-Strol-1E-2-In-1-Under-Desk-Treadmill-
FIG-15

Remote Control
A magnet built-in remote control so that it can be stuck in the storage cavity of side body as shown in figure.

UREVO-URTM023-Strol-1E-2-In-1-Under-Desk-Treadmill-
FIG-15
Note : Ensure that the walking treadmill is power on and the remote control is installed with battery.

Name Range Display
MPH 0.6-4.0 mph Displays the speed of walking belt.
TIME 00-99:59 minutes Displays the elapsed time.
Ml 00.00-99.99 miles Displays the distance that you have walked or

run.
STEP| 00-9999 steps| Disaplays the number of walked steps.
CAL| 0-9999 Kcal| Displays the approximate number of calories you have burned.

Operation of Remote Control

Buttons Functions Operation Note

| Start| Short press| Start the walking treadmill.

Stop

|

Long press for2″

| When the walking treadmill stop (all datas recover to 0 ), the screen will display “END”. 10 minutes later, the system will switch to the economic mode and turn off the display screen; Press any buttons

to wake up the treadmill.

Pause

|

Short press (in start mode)

| The screen will display “PALI”, previous workout metrics will be preserved automatically if pause time no longer than 10minutes, otherwise metrics data will be recovered to “0”; Press any buttons to wake up the treadmill. The treadmill will re-start at the minimum speed by re-pressing [> .
| M Mode| Short press| Customize countdown workout programs (like as: Time; Distance; Steps; Calories)
+| Accelerate| Short press| Long press over 0.5 seconds, the speed will be increased continuously.
–| Decelerate| Short press| Long press over 0.5 seconds, the speed will be decreased continuously.
| Mute| Short press| short press: Muted buzzer voices.

CARE & MAINTENANCE
Symptom: walk belt off-centered or slips. Centering walk belt process as follow:

UREVO-URTM023-Strol-1E-2-In-1-Under-Desk-Treadmill-
FIG-20

  1. Power off the treadmill and unplug the power cord.

  2. Manual centering process as follow: If the walk belt has shifted to left, use the hex tool to turn the left idler roller screw clockwise 1/4 of a turn(refer to figure 1 ). If the walk belt has shifted to right, use the hex
    tool to turn the right idler roller screw clockwise 1/4 of turn(refer to figure 2).

  3. The treadmill MUST work 1-2 minutes. Repeat the manual centering process until the walk belt is centered. The belt slip-correcting process as follow:

  4. Power off the treadmill before operation.

  5. Using the hex tool, turn both idler roller screws clockwise 1/2 of turn(refer to figure 3).

  6. fter correcting, please attempts to walk 1-2 minutes under 2-3mph speed setting. Repeat until the walk belt is properly tightened.
    Note : The Tread-belt should not be adjusted too tightly, otherwise it will be damaged. Attention

  7. To prevent any injury, don’t place any debris around the treadmill before the maintenance process.

  8. MUST use associated hex tool.

  9. Take care at the maintenance process. Do not pinch your fingers.

Belt lubrication process, follow the instructions below to lubricate belt

  1. Power off treadmill and unplug power cord.

  2. Using the hex tool, turn both idler roller screws counterclockwise till belt loosens and lifting easily.
    Tips: please markdown hex tool rotating cycles when loosen belt, which use for adapting belt tension after the lubrication process.

  3. Lifting edges of belt and spraying lubrication oil at center of walk platform evenly. Not necessary to apply spray lubrication oil on entire walk platform.

  4. Lubrication oil volume Per time of maintenance: 5-10ml.
    Attention : it would causes of belt slip if spray too much.

  5. Using the hex tool, turn the both idler screws clockwise as previous markdown number of turns until walk belt tighten properly.

  6. Power on the treadmill and work out for a few minutes, in order to spread lubrication oil to whole belt surface evenly. Attention: please hold handrail when workout at 4mph setting.

  7. Lubrication frequency: High recommends 100 Miles Per time.

Treadmill cleaning

  1. Power off treadmill and unplug power cord before cleaning.
  2. Wipe and clean with damp cloth, Do not cleaning with acidic or caustic detergents.
  3. Do not clean opposite of walk belt.
  4. Its normal few black powders are residual under treadmill after long working.

ERROR CODE

Error Code Fault Analysis Resolutions



E01

| ****


Communcation interrupted between contoller and numercic display.

| Unscrew motor hood and verify connection between controller and numeric display.

Please contact with after sale service if E01 code has not been eliminated.

Notice: Always power off and unplug power cord before processing.



E02

| ****


Motor open circuit

| 1. Unscrew motor hood to verify motor terminals connection .

2. Please contact with after sale service if problem CAN NOT solved by above process.




E03

| ****



Flame protection

| 1. Unscrew motor hood and verify connection between controller and motor.

2. Power supply interrput due to connector loosen or out, please unscrew motor hood to check.

3. Please contact with after sale service if problem CAN NOT solved by above process.





E04

| ****




Over current protection

| 1. Due to user over limited 120Kg.

2. Open to check any foreign objects blocked moving parts. (such as: drive motor, idler roller, driver roller, walking belt)

3. Walking belt is overtightened or lack of lubricant. (please see detail chapters relate to belt tension and lubricant process)





E05

| ****


Communcation interrupted between controller and dial display

| 1. Unscrew motor hood to verify signal cables connection

2. Unscrew upper control plane to verify signal cables connection

3. Replace new dial diaplay

4. Please contact with after sale service if problem CAN NOT solved by above process

TROUBLESHOOTING

Problem Fault Analysis Resolutions

No working

|

1. Power rock switch dyfunction.

2. Power supply interrputed.

3. Power cord damaged.

|

1. Replace new power rock switch if it doesn’t light on.

2. Make sure that power cord is plugged into properly grounded outlet.

3. Replace new power cable.

Dial display doesn’t lighted in Unfolded mode

|

Steering sensor dysfunction.

|

1. Unscrew upper control plane to verify steering sensor cable connection.

2. Unscrew upper motor hood to verify steering sensor cable connection.

3. Replace new steering sensor PCBA board.

4. Please contact with after sale service if problem CAN NOT solved by above process.

Numeric display doesn’t work in folded mode, but dial display work properly in unfloldl mode

Dial dysfucntion in unfolded mode

|

Dial dysfunction.

|

Replace new dial display.

Remote control does not work

|

1. Incorrect use of default.

2. Battery power shortage.

3. Remote control failure.

|

1. Remoter control should directly aiming to receiver port when in use.

2. Replace new battery cells.

3. Replace new remote control.

Walking belt slips

|

Walking belt loosen

| Tighten walking belt tension with hex tool

(1/4 a turn both idler roller screw clockwise)

Friction noise

|

Walking belt off center.

| See details of walking belt tension chapter.

WARRANTY
MANUFACTURER’S LIMITED WARRANTY
UREVO warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with UREVO Owner’s Manual. UREVO’s obligation under this warranty applies to the following:

COMPONENT LENGTH OF WARRANTY
Structural Frame 1 year For Home Use Only All Other Components 90 days For Home Use Only Exclusions from Warranty Coverage: UREVO does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:

  1. Improper installation and/or failure to abide by UREVO’s installation guidelines;
  2. Use of this product beyond normal home use, or in an application for which it was not designed;
  3. Cosmetic items such as scratches, dents or discolorations;
  4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
  5. any act of Nature (such as fire, flooding, snow, ice, hurricanes, earthquakes, lightnings or other natural disasters), environmental condition (such as air pollution, mold, mildew, etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
  6. Normal weathering due to exposure to sunlight, weather and atmosphere which can cause colored surfaces to among other things, flake, chalk, accumulate dirt or stains.
  7. Improper operation, alteration, handling, storage, abuse or neglect of the products. UREVO , using its sole discretion, will either repair or replace free of charge any part(s) proven to be defective under normal home use. Any repair or replacement shall provide no new warranty coverage, but shall retain only the remaining portion of the original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required.

When ordering replacement parts please have the following information ready:

  1. Order Number
  2. Description of Parts
  3. Adding photos or videos would be helpful) Part Number
  4. Date of Purchase

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals