UREVO URTM019 Strol 1 Pro Auto Incline Treadmill User Manual

UREVO URTM019 Strol 1 Pro Auto Incline Treadmill

IMPORTANT SAFETY INSTRUCTIONS

DANGER – To reduce the risk of electric shock:

1. Always unplug this treadmill from the electrical outlet immediately after using and before cleaning.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. A treadmill should never be left unattended or plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.
2. Do not operate under a blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
3. Close supervision is necessary when this treadmill is used by, on, or near children, invalids, or disabled persons.
4. Use this tread mi 11 on I y for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
5. Never operate this treadmill if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the treadmill to a service center for examination and repair.
6. Do not carry this treadmill by supply cord or use cord as a handle.
7. Keep the cord away from heated surfaces.
8. Never operate the treadmill with the air openings blocked. Keep the air openings free of lint, hair, and the like.
9. Never drop or insert any object into any opening.
10. Do not use outdoors.
11. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
12. Caution – To reduce the risk of injury from moving parts – Unplug before servicing.
13. Warning – To reduce the risk of Electric shock – Unplug before cleaning or servicing.
14. Warning – Risk of personal injury – Keep children under the age of 13 away from the machine.
15. To disconnect, turn all controls to the position, then remove the plug form the outlet.
16. Connect this treadmill to a proper outlet only. See grounding instructions.
17. This treadmill is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the treadmill by a person responsible for their safety. Keep children under the age of 13 away from this machine.
18. The maximum weight capacity for this product is 265 kg/120kg.

DO NOT EXCEED MAXIMUM WEIGHT CAPACITY.

GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

PRODUCT & ACCESSORIES

• Please carefully check whether the contents of the package are complete and intact.
• If there is any missing and damage, please contact the seller.

Accessories

SPECIFICATION

Product Configuration| Detailed parameters| Product Configuration| Detailed parameters
---|---|---|---

Product dimension (Folded down)

|

135.8 x 72 x 15cm cm

|

Product dimension (Folded up)

|

129 x 72 x 115 cm

53.5 x 28.4 x 5.9 inch

|

50.8 x 28.4 x 45 .3 inch

Running area

|

43 x 108 cm

|

Maximum speed

|

7.6 mph

17 x 42.5 inch

Gross weight

|

38 KG

|

Minimum speed

|

0.6 mph

83.8Lbs

Net weight

|

33.5 KG

|

Rate voltage

|

110 -120V ~

73.9 Lbs

Maximum load

|

120 KG

|

Peak horsepower

|

2.5 Hp

265 Lbs

|

Suggested age

|

14-60 years old

PRODUCT INTRODUCTION

HOW TO USE

Unfolded To Run (Speed range: 0.6- 7.6 mph)

1. Unbox to take out the treadmill with the related accessories, then place the treadmill on flat ground.

2. Counterclockwise rotating fold lever to unlock.

3. Lift up the uprights to the end position.

4. Clockwise rotating fold lever to lock.
   NOTE: Upright MUST fix security before running.

5. Fold down the handrail as horizontally.

6. Insert tablet mount refer to arrow sign.

7. Plug in the power cord to the power connector.

8. Power on and start to running.

Folded To Walk (Speed range: 0.6 – 4.0mph)

1. Detach the tablet mount.
2. Fold down the hand I bar subassemble under the reverse procedure.
3. Enjoy walk exercises with a remote control.

Safety Key

• In any emergency that occurs, the treadmill stops automatically and shows” —” when the safety key is pulled out from the console.
• NOTE: Find the clip (A) onto the waistband of your clothes, and another key (B) magnetic attracted under the console.

Transportation

1. If transportation is needed, please unplug the power cord and tablet mount before lifting the terminal of the treadmill.
2. Easy to transport treadmill with bottom transportation wheel assists, like as wheelbarrow.

NOTE: Before moving and storage, please make sure the power switch into off and the power cord is unplugged.

OPERATION

Console

Touch button feature

Reduce incline level.

|

Increase incline level.

| 3mph button: Short-touch this button, the speed will gradually change to 3mph.
| Customize workout goals (Ex: Time; Calories; Distance).
| •  To start walking belt and the initial speed setting is 0.6mph.

•  To stop the walking belt for a short pause or break, re-touch it again to resume.

|

Short-touch this button to stop the walking belt when your workout is completed.

| 6mph button: Short-touch this button, the speed will gradually change to 6mph.
| Decelerate: Short touch or hold down this button, the speed setting will change by 0.2mph.
| Accelerate: Short-touch or hold down this button, the speed setting will change by 0.2mph .

Standby Mode

• If the pause time is over 10 minutes, it will switch to “standby mode” automatically.
• In standby mode, not only console light off but also previous workout data will be erased to Zero, you can weak up the console by touching any button.

Display Screen

As you walk on or run on the treadmill, the display can show the following workout information:

Speed

|

0.6-7.6 mph

|

Displays the speed of the walking belt.

Calories| 0-9999 Kcal| Displays the approximate number of calories you have burned.
Inc| 0-3 level| Displays the incline level of your setting.
Time| 00 -99 minutes| Displays the elapsed time.
Distance| 00.00- 99.99 miles| Displays the distance that you have walked or run.

Note: Autonomy is 99 minutes.
You have to re-start the treadmill, in case your exercise time is over 99 minutes, and previous workout data will be erased and recounted accordingly.

Remote Control

Note: Ensure that the walking treadmill is powered on and the remote control is installed with a battery.
Operation of Remote Controller

| Start| Short press| Start the walking treadmill

Stop

|

Long press for 2″

| The display shows “End” and the walking belt slows down until I completely stop.

Display off if End status is longer than 10 minutes

Pause

|

Short press (in start mode)

| Take a pause while exercising, walking belt slows down until completely stops, the display shows” PAU” and the workout data will be preserved, re- press this button to resume.

Display off if pause longer than 10 minutes.

| Incline+| Short press| Increase incline level.
| Incline –| Short press| Decrease incline level.
|

Accelerate

|

Short press

| The walking belt speeds up, the increment is 0.2mph.
|

Decelerate

|

Short press

| Walking belt speed down, the decrement is 0.2mph.

Auto incline feature introduction

3 incline levels : 0 – 1 – 2 – 3

• Level 1: Approx 5% incline percentage
• Level 2: Approx 7% incline percentage
• Level 3: Approx 9% incline percentage

Friendly reminder of Auto-incline features

• The incline level should be set to “Zero” when you are finished exercising.
• Perform POST (Power On SelfTest) to identify the incline level and back to” Zero” automatically.
• Incline interval up to 20 seconds, total incline stroke “from Zero to Level 3 ” approximately 1 minute.

CARE & MAINTENANCE

Symptom: walk belt off-centered or slips

The centering walk belt process as follows:

1. Power off the treadmill and unplug the power cord.
2. The manual centering process as follows:
   • If the walking belt has shifted to the left, use the hex tool to turn the left idler roller screw clockwise 1/4 of a turn(refer to Figure 1 ).
   • If the walk belt has shifted to the right, use the hex tool to turn the right idler roller screw clockwise 1/4 of the turn(refer to Figure 2).
3. The treadmill MUST work 1-2 minutes. Repeat the manual centering process until the walking belt is centered.

The belt slip correcting process as follows

1. Power off the treadmill before operation.
2. Using the hex tool, turn both idler roller screws clockwise 1/2 of the turn(refer to Figure 3).
3. After correcting, please attempt to walk 1-2 minutes under 2-3mph speed setting. Repeat until the walking belt is properly tightened.

Note: The Tread-belt should not be adjusted too tightly, otherwise it will be damaged.

Attentions

1. To prevent any injury, don’t place any debris around treadmill before maintenance process.
2. MUST use associated hex tool.
3. Take care at maintenance process. Do not pinch fingers.

Belt lubrication process, follow instruction below to lubricate belt.

1. Power off treadmill and unplug power cord.

2. Using the hex tool, turn both idler roller screws counterclockwise till belt loosen and lifting easily.
   Tips: please markdown hex tool rotating cycles when loosen belt, which use for adapting belt tension after lubrication process.

3. Lifting edges of belt and spraying lubrication oil at center of walk platform evenly. Not necessary to apply spray lubrication oil on entire walk platform.

4. Lubrication oil volume Per time of maintenance: 5-10ml. Attention: it would causes of belt slip if spray too much.

5. Using the hex tool, turn the both idler screws clockwise as previous markdown number ofturns untill walk belt tighten properly.

6. Power on treadmill and workout for a few minutes, in order to spread lubrication oil to whole belt surface evenly.

Attention: please hold handrail when workout at 4mph setting.
Lubrication frequency: High recommend 100 Miles Per time.

Treadmill cleaning

1. Power off treadmill and unplug power cord before cleaning.
2. Wipe and clean with damp cloth, Do not cleaning with acidic or caustic detergents.
3. Do not clean opposite of walk belt.
4. Its normal few black powders residual under treadmill after long working.

ERROR CODE

IMPORTANT: If error code appears, you MUST stop workout immediately, Please contact with after sale service if problem CAN NOT be solved after restart.

TROUBLESHOOTING

Problem   Fault Analysis   Resolutions

No working

|

1. Power rock switch dyfunction.

2. Power supply interrputed.

3. Power cord damaged.

|

1. Replace new power rock switch if it doesn’t light on.

2. Make sure that power cord is plugged into properly grounded outlet .

3. Replace new power cable.

Walking belt slips

|

Walking belt loosen

|

Tighten walking belt tension with hex tool

( 1/4 a turn both idler roller screw clockwise)

Remote control does not work

|

1. Incorrect use of default.

2. Battery power shortage.

3. Remote control maulfunction.

|

1. Remotor control should directly aiming to receiver port when in use.

2. Replace new battery cells.

3. Replace new remote control.

Friction noise|

Walking belt off center.

|

See details of walking belt tension chapter.

WARRANTY

MANUFACTURER’S LIMITED WARRANTY
UREVO warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with UREVO Owner’s Manual. UREVO’s obligation under this warranty applies to the following:
COMPONENT LENGTH OF WARRANTY
Structural Frame 1 year For Home Use Only All Other Components 90 days For Home Use Only
Exclusions from Warranty Coverage
UREVO does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:

1. Improper installation and/or failure to abide by UREVO’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it was not designed;
3. Cosmetic items such as scratches, dents or discolorations;
4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
5. Any act of Nature (such as fire, flooding, snow, ice, hurricanes, earthquakes, lightnings or other natural disasters), environmental condition (such as air pollution, mold, mildew, etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
6. Normal weathering due to exposure to sunlight, weather and atmosphere which can cause colored surfaces to among other things, flake, chalk, accumulate dirt or stains.
7. Improper operation, alteration, handling, storage, abuse or neglect of the products.

UREVO , using its sole discretion, will either repair or replace free of charge any part(s) proven to be defective under normal home use. Any repair or replacement shall provide no new warranty coverage, but shall retain only the remaining portion of the original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required.
When ordering replacement parts please have the following information ready:

1. Order Number
2. Description of Parts (Adding photos or videos would be helpful)
3. Part Number
4. Date of Purchase

IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. The specifications of this product may vary from this photo, subject to change without notice.
Manufacturer:

• Shenzhen Vile Dynamic Technology Co., LTD.
• Address: 1205-1206, Tianliao Building, Tangchang Road, Tanglang
• Community, Taoyuan Street, Nanshan District, Shenzhen, China

CUSTOMER SERVICE

• IMPORTANT: FOR UREVO ONLY
• For damaged or defective product, questions, replacement parts or any other service
• support, please contact our customer service department by the below methods:
• services@urevosports.com
• Response Time: 24-48 hours
• Emailing us with the Order ID will be the best method to receive a response during peak business hours.
• Website: www.urevosports.com
• US Support Hotline: (1 )844-998-2473
• Hours of Operation: Monday- Friday : 9 AM – 12 PM ; 1 PM – 6 PM (PST)
• PLEASE DO NOT RETURN THIS PRODUCT WITHOUT ASKING OUR CUSTOMER SERVICE FIRST.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>