CHASING CM600 Robotic Pool Cleaner Instructions

June 5, 2024
CHASING

chasing logo

CHASING CM600 Robotic Pool Cleaner

CHASING CM600 Robotic Pool Cleaner

INTRODUCTION

Thank you for purchasing and using the CHASING CM600, a robotic pool cleaner. It will provide you a convenient, reliable, and cost-effective cleaning experience.

WARNINGS

  1. DO NOT enter the pool until CM600 is removed from the pool.
  2. DISCONNECT the power supply when examining CM600.
  3. Keep children away from CM600 when it works.
  4. Ensure that the original power cable is used
  5. Power cable only could be replaced by technicians certified by the manufacturer.
  6. Ensure that the power supply of CM600 is ground connection reliably.
  7. DO NOT touch its rotating unit while it is operating. CHASING CM600 Robotic Pool Cleaner 1
  8. Keep the power supply at least 3M from pool s edge, 0.1M above the ground while it is operating.

CM600 PARTS

  1. Robot pool cleaner (including cable)CHASING CM600 Robotic Pool Cleaner 2
  2. power supplyCHASING CM600 Robotic Pool Cleaner 3
  3. filtrationsCHASING CM600 Robotic Pool Cleaner 4

How To Use CM600

  1. Position the power supply at a distance of 3M from pool’ s edge, and 0.1M above the ground at least.
  2. Unwind the cable and stretch it out completely so that it has no kinks.
  3. Attach the cable to power supply, lined up with the groove in the socket, tighten the nut.CHASING CM600 Robotic Pool Cleaner 5
  4. Place CM600 in the pool.
  5.  Plug in the power supply. CHASING CM600 Robotic Pool Cleaner 6
  6. Click “MODE” button to select a cleaning mode, the corresponding light will be lit. CHASING CM600 Robotic Pool Cleaner 7
  7. Click “START/STOP” button to stat CM600, it will work until a cleaning cycle finished. CHASING CM600 Robotic Pool Cleaner 8
  8. The light of CM600(at the position shown in the figure) will be flashing while cleaning. CHASING CM600 Robotic Pool Cleaner 9

LED indications table:

Meaning Lights display
Self-Checking White constant
Standby Yellow constant
Out of water Purple constant
Pause Green blinking
Normal operation Cycle on
--- ---
Error Red blinking

After a cleaning cycle, click “PULL Up” button, CM600 wll reach the wall, and rise above the thewater surface. You can also gently drag its cable to get CM600 come to the edge of the pool.

CHASING CM600 Robotic Pool Cleaner 10

Grab the robot by the handle and pull it out the water. DO NOT pull it out the water by dragging the cable.

CHASING CM600 Robotic Pool Cleaner 11

After cleaning cycle, open the filter cover, lift the basket, clean the filter basket.

CHASING CM600 Robotic Pool Cleaner 12

STORAGE

If CM600 will not be in use for an extended period of time, make sure that no water is left in it, roll up the cable so that it has no kinks. You can store CM600 in a protected area out of direct sun/rain/frost, at a temperature of between 5°-45°C.

FCC Statement

This equipment has been tested and found to comply with the limits for a Clas B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiO communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.
  •  Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals