StyleWell HDFP62-70E Chelsea 62 Inch Freestanding Electric Fireplace TV Stand Instruction Manual

HDFP62-70E Chelsea 62 Inch Freestanding Electric Fireplace TV Stand
Instruction Manual

OMSID # 320084815 sw I ewe I I ”
Model #HDFP62-70E
ASSEMBLY INSTRUCTIONS
62in. Infrared Media Electric Fireplace

HDFP62-70E Chelsea 62 Inch Freestanding Electric Fireplace TV Stand

Questions, problems, missing parts?
Before returning to the store, call Customer Service
8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. — 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM

THANK YOU
We appreciate the trust and confidence you have placed in StyleWell through the purchase of this electric fireplace/heater. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing StyleWell!

Safety Information

Please read and understand these instructions before assembling and using this console. Save these instructions for future reference.
MAXIMUM RECOMMENDED WEIGHT LOADS
WARNING: This unitis not intended for use with CRT TVs. Use only with flat panel TVs and audio/video equipment meeting recommended size and weight limits. Never use with larger/heavier than recommended flat panel TVs or equipment. To avoid  instability, place fiat panel TV in the centre of the unit; the base of the television must be able to rest on the supporting surface of the unit without over-hanging the edges. Improperly positioned fiat panel TVs, or flat panel TVs or other equipment that exceed recommended size and weight limits could fall off or break the unit, causing possible serious injury.

Warranty

We are confident that you will be delighted with this purchase. Should this product be defective in workmanship or materials, or fail under normal use, we will repair or replace it for a period of up to one (1) year from date of purchase.
This warranty gives you specific rights and you may also have other rights which vary from state to state.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

Pre-Assembly‘

PLANNING ASSEMBLY
Compare all parts with the Hardware Included and Package Contents list. If any part appears missing or damaged, do not assemble this product and contact the Customer Service Team at 1-877-527-0313.
TOOLS REQUIRED Phillips screwdriver (not provided)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Assembly

1. Preparing base assembly
   NOTE: Do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will mak the assembly easier.
   o Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratches.
   o Securely screw the cam bolts (EE) into the designated small holes on the bottom panel (M) and skirtings (N, P and Q) using a Phillips screwdriver.

2. Gluing wood dowels
   NOTE: Refer to the dowel guide drawings in this step for further clarification on how to properly glue in the wooden dowels. Apply this method whenever instructed to install wood dowels.
   o Glue the wood dowels (CC) into the designated holes on the skirtings (N, 0, P and Q), base center support (R), firebox supports (A1 and B1). It is very important to use a small amount of glue on both ends of dowels and wipe away the excess glue immediately.

3. Attaching rear skirting
   NOTE: Refer to the cam lock assembling guide drawings in this step for further clarification on how to properly install cam locks. Apply this method whenever instructed to install cam locks.
   o Attach the rear skirting (0) between the side skirtings (P and Q) by engaging two cam locks (DD).

4. Attaching base center support
   o Attach the base center support (R) to the front skirting (N) by engaging one cam lock (DD).

5. Attaching front skirting
   o Align and attach the front skirting (N) to both side skirtings (P and Q) using two cam locks (DD).
   o Insert two long flat head screws (GG) through the the rear skirting (0) and securely screw into base center support (R) using a Phillips screwdriver.

6. Attaching base
   o Using the wood dowels (CC) as guide, align and attach the previous assembly to the bottom panel (M) by engaging 13 cam locks (DD).

7. Attaching firebox short supports
   o Fasten two firebox short supports (B1) to the top face of bottom panel (M) using two long flat head screws (GG).

8. Attaching firebox long support
   o Fasten the firebox long support (A1) to the bottom panel (M) with three long flat head screws (GG).

9. Preparing media shelf and partition panel assembly
   o Securely screw the cam bolts (EE) into the designated small holes on the media shelf (L), partition panels (T and U) and partition moldings (W and X) using a Phillips screwdriver.

10. Gluing wood dowels
    o Glue the wood dowels (CC) into the inner holes on the media shelf (L), partition panels (T and U), top front stretcher (Y) and middle crosshar (Y) as shown.

11. Attaching partition moldings
    o Using the wood dowels as a guide, align and attach the left partition molding (W) to the the left partition panel (T) using six short flat head screws (FF) through the pre-attached plastic coonectors and screw into place untill tight.
    o Repeat the same proceess to combine the right partition panels (U) and the right partion molding (X).

12. Install door stoppers
    o Using the pilots holes as a guide, fasten one door stopper (Il) to each partition panel (T and U) with two short flat head screws (FF).

13. Attaching middle crossbar
    o Attach the middle crossbar (Z) to the media shelf (L) by engaging four cam locks (DD).

14. Attaching partition panels
    o Align and attach the left partition panel (T) to the media shelf (L) and top front stretcher (Y) by engaging three cam locks (DD).
    o Repeat the same process to attach the right partition panel (U) at the opposite end.

15. Preparing top panel and bottom panel assembly
    o Securely screw the cam bolts (EE) into the designated small holes on the top panel (K) and bottom panel (M).

16. Gluing wood dowels
    o Glue the wood dowels (CC) into the inner holes on the side panels (S) as shown.

17. Attaching bottom panel
    o Using the wood dowels as guide, firmly press the assembled partition panels (T and U) to the bottom panel (M) and fasten them in place with four long flat head screws (GG).

18. Attaching side panels
    o Align and attach the side panels (S) to the bottom panel (M) by engaging four cam locks (DD) as shown.

19. Attaching top panel
    o Position the top panel (K) onto the vertical panels and the top front stretcher (Y) properly and fasten it in place by engaging twelve cam locks (DD).
    o Now, go back and securely tighten all the cam locks and screws. Make sure all the parts are tight and there are no gaps between the parts. This will help keep the unit square.

20. Installing back panels
    o Ask for assistance to flip around the previous assembly at its front edges.
    o Pick up the middle back panel (E1) and align the pre drilled holes against the upper long edge with the pilot holes on the back of top panel (K), fasten it in place with the provided washer head screws (HH).
    o Using the pilot holes as a guide, align and attach the side back panels (D1) to the mantel frame with the washer head screws (HH).
    NOTE: We recommend attaching back panel with the screws at the corners first.

21. Fastening partition panel moldings
    o With the pilot holes as a guide, fasten the firebox long support (A1) to the partition moldings (W and X) by attaching two mending plates (JJ) at the joints, using two short flat head screws (FF) per plate.

22. Installing the door hinges
    o Extend two door hinges (PP) and rest the hinge cups onto the cutouts of each door (V). Secure the door hinges (PP) in place by using two nickel screws (QQ) in each.
    o Attach one handle (MM) to the front side of each door (V) with two handle bolts (NN).

23. Attaching door panels
    o Ask for assistance to lift the assembly unit upright and position it near the final location.
    o Pick up one door (V) and fasten the hinge bases onto the left side panel (S) with four nickel screws (QQ) in each.
    o Repeat the same process to attach the other door (V) to the right side panel (S).
    o Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the screws for a good fit. Refer to the hinge sticker on door for adjustment.

24. Attaching adjustable shelves
    o Open the doors and insert eight shelf supports (KK) in the holes at the desired height inside each side compartment. Make sure you place the four shelf supports at the same level so the shelf is not tilted. Tilt and rest the adjustable shelves (F1) onto the  shelf supports

25. Plugging cam covers
    o Plug the cam lock covers (00) onto the visible cam locks to conceal the cams.

26. Attaching upright arms
    IMPORTANT NOTE: Use hand screwdriver, not power driver to assemble fireplace insert.
    0 See figure A: Fasten upper 2 screws (AA) through the upright arm (C) into the heater () until tight.
    0 See figure B: Fasten lower 2 screws (AA) into the upright arm (C) until tight.
    0 Fully tighten all 4 screws (AA) one final time
    0 Repeat the same process with upright arm (B).
    WARNING: Do not lift or transport the heater by using the upright arms.
    

27. Attaching logs to ember bed
    IMPORTANT: Carefully follow the 2 steps below for inserting each log.
    1. Install left log (F) into left hole of ember bed (E) by inserting front edge of base of the log into front notches of ember bed hole.
    2. Then tilt the log back to insert the rear edge of the log base into rear notches of ember bed hole (press down log firmly to lock into position).
    o Repeat the above process for the right log (G).

28. Positioning ember bed
    o Setthe ember bed (E) onto the heater (A) as shown.
    o Push ember bed forward against the front flange of heater.
    o Position the USB cable as shown below.

29. Attaching wall panel
    0 Fold the wall panel (H) as shown. Then position yourself at back side of heater (4).
    0 Hold wall panel (H) at the angle shown below and insert lower back edge into metal slots on back of heater (A).
    0 Tilt wall panel (H) forward until bottom corner inserts into lower U-channels on both upright arms (B and C).
    0 Continue to tilt wall panel (H) forward until the top corner inserts into upper U-channels on both upright arms (B and C).

30. Connecting ember bed cable to heater
    o Fully plug the USB connector of the ember bed (E) into the back port of heater (A).

31. Inserting the glass
    o Slide the glass (1) into the inner U-channels on both upright arms (B and C) until the glass sits onto the heater (A). If needed, push top of upright arms in or out to accommodate glass. Make sure the top of the glass (I) is flush with the top of both upright arms (B nd C).

32. Positioning connector strap
    o Position top connector strap (D) over the glass (I) and upright arms (B and C). Follow orientation shown below.

33. Attaching connector strap
    o Fasten connector strap (D) to both upright arms (B and C) using two screws (AA) as show below. Holes must be in line for screw to pass through.

34. Finishing fireplace insert assembly
    o The firebox is now ready for the next assemble step.

35. Installing fireplace insert
    o Lift the fireplace insert carefully into the back of the assembled mantel and centre it on the firebox short supports in the opening.
    o Use the pilot holes as a guide, fasten two L-shaped brackets (LL) onto the firebox holder (C1) with four pan head screws (BB), Make sure that the right angle side is flush with the short edge of firebox holder (C1).
    o Use the pilot holes as a guide, fasten the firebox holder (C1) between the partition panels (T and U) with four pan head screws (BB).

36. Installing acrylic stopper
    o Remove the paper backing of acrylic stopper (RR), then properly align the acrylic stopper into the cutout on the acrylic stopper template on the front of the top panel (K). Press down on the acrylic stopper to help adhesion.
    NOTE: To prevent your TV from tipping, you must install the acrylic TV stopper if you place a flat panel television on the top panel.
    Otherwise, skip to next step.
    o Atthe back of top panel (K), grip the heads of plastic tacks with pliers, with twisting motion pull tacks loose to remove the acrylic stopper template.

37. Interchanging door insert panels
    o To change door panels, loosen the screws on the inside of the door and rotate the clips to remove the panel. Replace with the desired panel, then rotate clips to secure the panel within the door frame and tighten screws.
    NOTE: The glass door panels are pre-attached when shipping. You can keep as is or interchange as the desired configuration.

38. Installing tipping restraint hardware
    WARNING: Young children can be seriously injured by tipping furniture. You must install the tipping restraint hardware with the unit to prevent the unit from tipping, causing any accidents or damage. The tipping restraints are intended only as a  deterrent, they are not a substitute for proper adult supervision. The tipping restraints are not earthquake restraints. If you wish to add the extra security of earthquake restraints, they must be purchased and installed separately.
    o With assistance, position the assembled fireplace at the desired location against a wall. If necessary, adjust the pre-attached floor levelers by hand to correct tilting and level the doors, until the unit is level.
    o Follow the instructions printed on the plastic bag containing the tipping restraint hardware to attach the tip-over restraints to the unit and the wall.
    o Connect the fireplace to the power transformer. Follow the operating manual for the electric fireplace insert to control your fireplace.

Care and Maintenance

A touch-up pen has been provided to minimize the small nicks or scratches that may occur during assembly or shipping.
To clean and care for your furniture:

• Use a soft, clean cloth that will not scratch the surface when dusting.
• Use of furniture polishes is not necessary. Should you choose to use polishes, test first in an inconspicuous area.
• Using solvents of any kind on your furniture may damage the finish.
• Never use water to clean your furniture as it may cause damage to the finish.
• Always use coasters under beverage glasses and flowerpots.
• Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
• Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish.
• In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture.
• Check bolts/screws periodically and tighten them if necessary.

CARING FOR WOOD FURNITURE

Itis best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.

CLEANING THE FIREPLACE TRIM

Clean the metal trim using a soft cloth, slightly dampened with citrus oil based product and buff with a clean soft cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim. Citrus oil based products can be obtained at supermarkets or hardware stores.
WARNING

• Unit must be placed on a level surface or leveled with included hardware (when applicable).
• Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
• For safety reasons, it is imperative that this unit be mounted to the wall or floor.
• Unit can tip over causing severe injury or death.
• Never open more than one drawer at a time.
• Do not exceed the recommended weight limits.
• Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical, plumbing and gas lines. Cutting may cause serious injury.

Questions, problems, missing parts?
Before returning to the store,
call StyleWell Customer Service
8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>