Shinex Electronic Industries DCPC03 Device User Manual
- June 5, 2024
- Shinex Electronic Industries
Table of Contents
Shinex Electronic Industries DCPC03 Device User Manual
Product Name: SHINEX ACDK
Model Name: DCPC03
Please refer the following information for setting up.
Control, Operation, Settings
- Login settings
- Individual control
- Collective starting/stopping and settings for control group
- Schedule control
- Interlocking control
- Emergency stop control for fires
- Power failure and recovery processing control
- Centralized control of air conditioners
| Parameter | Description |
|---|---|
| USB2 | USB_ACDK |
| USB1 | USB_ACDK |
| Micro SD | Micro SD Solt |
| LAN | Network |
| RS485 | RS485 D1+、D1-、D2+、D2- |
| Type C | Power In 5V3A |
| CPU | Dual-Core |
| --- | --- |
| Memory | RAM System |
| Storage | Emmc |
Input Power Range
|
Type C
| 5VDC power input, +-5% tolerance
Use USB type C as power connector on rear I/O
M/B Form Factor| | PCB dimension 168 x 82mm
Other Components| Battery| CR2032 coin cell,by on board socket
Display Interface|
Panel
| Screen Size 10.1 inches (diagonal)
Display Format 1024(H) x (R,G,B) x 600(V) dots Back-light LED
LCD Active Area 222.72(H) × 125.28(V) mm
LVDS
| 1 x LVDS: resolution up to 1024*600@60Hz LVDS header follows panel spec
Panel Power default 3.3V,5V can be optional
Backlight
| 1 Pin wafer for backlight with 5V, 1A current.
Signal includes PWM brightness control,power on/off signal
Interface|
LAN
| 1 GbE speed LAN on rear I/O,by AR8033 Ethernet transceiver.
CPU has Iimitation note on full speed throughput
USB 2.0| 2 x USB 2.0 Type A on rear I/O
RS485
| 2 x RS485 on rear I/O
6 pin terminal block connector
I2C| One I2C header for touch control
SD Card| 1 x Micro SD card on rear I/O
M.2 2230
| M.2 socket E key,support type 2230
With Wi-Fi M.2 2230 Moudule Card RTL8822CE(ENLI) on M.2 socket
Test port| Debug UART
USB OTG| USB2 OTG,micro USB,for service purpose
Other
| Thermal sensor| One thermal sensor
Auto power on| Auto power on
Other Jumper| Dip switch| Dip switch for system setting
OS Support| OS Support| Support Linux NXP i.MX6 Yocto 2.5
Temperature
| Store
Operating
| 0 to 60 °C
0 to 40 °C
Weight
Size
|
Host bady
| 1098.65g ± 50g
(W)272.2 ± 0.7mm (D)181.6 ± 0.7mm (H)36.1 ± 0.7mm
Federal Communication Commission Interference Statement
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Note, Supplier’s Declaration of Conformity §2.1077(a)(3)
Name: __SHINEX ACDK Address: @USA
Telephone number or Internet contact