StyleWell SP5293 Wallmount Fireplace with Mood Light User Manual
- June 3, 2024
- StyleWell
Table of Contents
- StyleWell SP5293 Wallmount Fireplace with Mood Light User Manual
- ELECTRIC FIREPLACE HEATER
- Warning
- SAFETY INFORMATION
- IMPORTANT INSTRUCTIONS
- SAFETY INFORMATION
- Electrical Connection
- ELECTRICAL SPECIFICATIONS
- PRE-INSTALLATION
- Hardware Contents
- PRE-INSTALLATION
- IMPORTANT:
- Before you install
- INSTALLATION
- Step 2.
- Step 3.
- Step 4.
- Step 5.
- Step 6.
- Step 7.
- Step 8.
- Step 1.
- Step 2.
- Step 3.
- Step 4.
- OPERATING INSTRUCTIONS
- [](https://manuals.plus/wp-content/uploads/2022/12/StyleWell-SP5293
- [](https://manuals.plus/wp-content/uploads/2022/12/StyleWell-SP5293
- OPERATING INSTRUCTIONS
- [](https://manuals.plus/wp-content/uploads/2022/12/StyleWell-SP5293
- OPERATING INSTRUCTIONS
- CARE AND MAINTENACE
- CARE AND MAINTENACE
- Replacing the Remote Control Battery|
- Note:
- Disposal of Used Battery
- TROUBLE SHOOTING GUIDE
- 1 YEAR LIMITED WARRANTY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
StyleWell SP5293 Wallmount Fireplace with Mood Light User Manual
ELECTRIC FIREPLACE HEATER
ATTENTION
FIND A LOCATION FOR THE FIREPLACE HEATER THAT IS PROTECTED FROM DIRECT SUNLIGHT. FAILURE TO READ ALL INSTRUCTIONS MAY RESULT IN A POSSIBLE ELECTRIC SHOCK, FIRE HAZARD AND / OR INJURY WILL VOID THE WARRANTY
CONSUMER SAFETY INFORMATION PLEASE READ THIS MANUAL BEFORE INSTALLING AND OPERATING THIS APPLIANCE
Warning
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY AN ELECTRIC SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
This equipment has been tested and found to comply with the limits for Class B
digital devices, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. The equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on. The user is
encouraged to try and correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and the receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed
to reduce the risk of fire, electric shock and injury to persons, including
the following:
Read all instructions before installing or using the heater.
DANGER: If the information in this
manual is not followed exactly, an electric shock or fire may result causing
property damage, personal injury or loss of life.
WARNING: This appliance is hot
when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. Keep
combustible material, such as furniture, pillows, bedding, papers, clothes and
curtains, at least 3 feet from the front of the heater and keep them away from
the side and rear.
WARNING: Extreme caution is
necessary when any heater is used by or near children or individuals with
disabilities and whenever the fireplace is left operating and unattended.
WARNING: DO NOT run cord under
carpeting. DO NOT cover cord with throw rugs, runners, or similar covering.Do
not route cord under furniture or appliances. Arrange cord away from traffic
areas and where it will not be tripped over.
WARNING: Do NOT insert or allow
foreign objects to enter any ventilation or exhaust opening as this may cause
an electric shock or fire, or damage the appliance.
WARNING: This appliance has hot
and arcing or sparking parts inside. DO NOT use it in areas where gasoline,
paint or flammable vapors or liquids are used or stored. This fireplace should
not be used as a drying rack for clothing. Christmas stockings or decorations
should not be hung in the area of it.
SAFETY INFORMATION
Use this appliance only as described in the manual. Any other use is NOT recommended by the manufacturer and may cause fire, electric shock or injury to persons.
CAUTION
- If possible, ALWAYS unplug this appliance when not in use.
- DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions.
- DO NOT operate any heater if it has been dropped or damaged in any manner. Disconnect power at service panel and have heater inspected by a reputable electrician before reusing.
- Any repairs to this fireplace should be carried out by a qualified service person.
- Under no circumstances should this fireplace be modified. Parts having to be removed for servicing must be replaced prior to operating this fireplace again.
- DO NOT use outdoors.
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER place heater where it may fall into a bathtub or other water container.
- To disconnect this appliance, turn controls to the off position, then remove plug from outlet.
- ONLY connect to properly grounded outlets.
- This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian Electrical Code or follow the National Electrical Code, ANSI/NFPA N0.70.
- To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where opening may become blocked.
- The heaters MUST NOT be located immediately below a socket-outlet.
- ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip).
- There is a thermostat protective device provide inside of unit. If the inner temperature overheats or abnormal heating occurs, the thermostat protective device will cut off power supply to prevent damage or risk of fire.
- DO NOT place any objects on top of insert and top air intake vents as this will cause unit to overheat and can cause a fire.
Electrical Connection
- A 15-amp, 120-volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with 6-ft. three-wire cord, exiting from the rear of the fireplace. DO NOT exceed the current rating of the current tap. ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip).
- This heater is for use on 120 volts. The cord has a plug as shown below. See illustration for grounding instruction. An adapter as shown at C is available for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
ELECTRICAL SPECIFICATIONS
Voltage: 120 VAC, 60 Hz
Amps: 11.7 Amps
Watts: 1400 Watts
PRE-INSTALLATION
Package Contents
Part | Description | Quantity |
---|---|---|
A | Front Glass Cover | 1 |
B | Base | 1 |
C | Fireplace | 1 |
Part | Description | Quantity |
--- | --- | --- |
D | Mounting Bracket | 1 |
E | Remote Control | 1 |
F | Rocks | 1 Bag |
Hardware Contents
Number of the hardware in ( ) is separated for backup
PRE-INSTALLATION
Tools Required
IMPORTANT:
Please read and understand this manual before any assembly. Before beginning
assembly of product, make sure all parts are present. Compare parts with
packaging contents list. If any part is missing, or if
you have any questions, contact the service center at
1-844-455-4621. Place all parts from
the box in a cleared area and position them on the floor in front of you.
Remove all packing materials and place them back into the box. Do not dispose
of the packing materials until assembly is complete.
Read each step carefully before beginning any assembly and make sure you
understand each step. If you are missing a part, please call for assistance
1-844-455-4621.
Before you install
Before installing your new fireplace, decide whether you want to install your
new fireplace using a surface mount or freestanding.
Select a location that is not susceptible to moisture, dust and is away from
high traffic locations and things that many catch fire or block openings such
as drapes, pillows, furniture etc.
It is strongly recommended that the screws be screwed into the wall studs
where possible.
If the wall studs cannot be used, wall anchors must be used.
CAUTION: Enclosed wall anchors (BB) only can be use on the concrete wall.
For the best effect install the fireplace out of direct sunlight and away from
overhead lighting.
INSTALLATION
WALL MOUNT INSTALLATION
Step 1.
Remove mounting bracket (D) from back of fireplace (C) by unscrew two screws at the top of the unit.
Step 2.
Release the latches on the both side to unlock the front glass as illustrated below. Carefully pull the front glass (A) slightly away from the fireplace (C) and set down. Then gently pull the release tab on the cable and finish removing front glass (A).
Step 3.
Remove the base (B) of fireplace (C) by unscrewing three screws at the rear base of the unit
Step 4.
Choose a wall location to attach the mounting bracket (D). Position the
mounting bracket (D) in the desired location. Use a level to align the bracket
and mark the four holes with a pencil.
Step 5.
Select the hardware appropriate for mounting bracket installation.
STUD WALL
- Secure the mounting bracket (D) to wall using screws (AA) at marked stud locations.
DRYWALL
- Drill holes at marked locations and secure the mounting bracket (D) to the wall with toggle bolts and washers (not included).
CONCRETE WALL
- Drill 5/16-inch holes at marked locations, then insert wall anchors (BB) into holes. Secure the mounting bracket (D) to wall using screws (AA).
Step 6.
Hang the fireplace (C) on the hooks at bottom of mounting bracket (D) and push the fireplace (C) into mounting bracket (D). Re-fasten the two screws removed in Step 1
Step 7.
Distribute the rocks (F) evenly in the tray of the fireplace (C).
Step 8.
Re-install the front glass (A) to the fireplace (C), and connect the mood light cable.
FREESTANDING INSTALLATION
Step 1.
Assembly the base (B) of fireplace (C) by fasten three screws.
Step 2.
Release the latches on the both side to unlock the front glass as illustrated below. Carefully pull the front glass (A) slightly away from the fireplace (C) and set down. Then gently pull the release tab on the cable and finish removing front glass (A).
Step 3.
Distribute the rocks (F) evenly in the tray of the fireplace (C)
Step 4.
Re-install the front glass (A) to the fireplace (C), and connect the mood light cable.
OPERATING INSTRUCTIONS
[](https://manuals.plus/wp-content/uploads/2022/12/StyleWell-SP5293
-Wallmount-Fireplace-with-Mood-Light-User-Manual_19.jpg)Power Button
- Pressing the power button will turn ON or OFF the unit.
- When the unit is in ON mode, touch control panel light will fully light up for 8 sec and then shut down if without any others operation including remote control.
- When the unit is in OFF mode, the POWER symbol LED will Semi-bright. When power OFF, unit will be stopped, if heater is working before power OFF the unit, fan will have 20 seconds delay to ensure heat will not be trapped inside the unit.
[](https://manuals.plus/wp-content/uploads/2022/12/StyleWell-SP5293
-Wallmount-Fireplace-with-Mood-Light-User-Manual_20.jpg)Flame Button
- Press the flame button to cycle through the setting as:
Flame Brightness (FL), Flame Color (FC), Mood Light Brightness (bL), Mood Light Color (bC)
Flame Brightness Setting
- Press “Flame” key until FL0 / FL1 / FL2 / FL3 / FL4 / FL5 shown on the display, and then press “+” key or “-” key to adjust the flame brightness from level 0 to level 5.
Flame Color Setting
- Press “Flame” key until FC1 / FC2 / FC3 / FC4 / FC5 /FC6 shown on the display, and then press “+” key or “-” key to adjust the flame color.
Setting | Color |
---|---|
FC1 | Yellow |
FC2 | Blue |
FC3 | Yellow + Red |
Setting | Color |
--- | --- |
FC4 | Yellow + Blue + Red |
FC5 | Yellow + Blue |
FC6 | Auto Change |
OPERATING INSTRUCTIONS
Mood Light Brightness Setting
- Press “Flame” key until bL0 / bL1 / bL2 / bL3 / bL4 / bL5 shown on the display, and then press “+” key or “-” key to adjust the mood light brightness from level 0 to level 5.
Mood Light Color Setting
- Press “Flame” key until bC1 / bC2 / bC3 / bC4 / bC5 / bC6 / bC7 / bC8 / bC9 / bC10 shown on the display, and then press “+” key or “-” key to adjust the mood light
Setting | Color |
---|---|
bC1 | Red |
bC2 | Orange |
bC3 | Yellow |
bC4 | Green |
bC5 | Cyan |
Setting | Color |
--- | --- |
bC6 | Blue |
bC7 | Purple |
bC8 | White |
bC9 | Above 8 colors gradually changed |
bC10 | RGB 3 colors gradually changed |
Timer Setting
- Timer can be adjusted when heater is ON. It can adjusted from 0 hour (OFF) to 9 hours with 0.5 hour interval.
- When TIMER is activated, the symbol will be displayed.
- When TIMER digital is 0 H, TIMER function is invalided. The TIMER symbol will automatically disappear
Clock Setting
- For clock setting, hold the TIMER key for 5s, hour display will flashing. Push UP “+” or DOWN “-” key, Hours setting can be adjusted. Touch the TIMER key once more, minute display will flashing. Minutes setting can be adjusted as the same way as hours setting.
- When clock is at the setting mode, hold UP (“+”) and DOWN (“-”) keys together to select 12H or 24H mode. The unit default setting is The AM or PM symbol will automatically displayed when the 12H mode was selected.
- Press the timer key can exit the setting or it will automatically exit after 8s without any further operation.
[](https://manuals.plus/wp-content/uploads/2022/12/StyleWell-SP5293
-Wallmount-Fireplace-with-Mood-Light-User-Manual_22.jpg)Heater Button:
Temperature Setting
- HEATER key is used to control ON/OFF of the heater. Push UP (“+”) or DOWN (“-”) key to to scroll through the pre-set temperature range from 59°F (15°C) to 86°F (30°C), ON & OF (OFF). Heater will turned ON accordingly to the set temperature. When the ambient temperature is higher than the set temperature, heater will automatically turned OFF.
- When the temperature is set at “ON”, heater will be working continuously.
- When HEATER is activated, the heater & temperature symbol will displayed.
- When the heater is ON, hold the HEATER key for 3 sec; this allow the temperature unit change from °C to °F or
°F to °C. The unit default setting is °F.
OPERATING INSTRUCTIONS
- Control the setting of flame brightness, flame color, mood light brightness, mood light color, timer, clock and temperature .
Child Lock
Activate Child Lock
When the unit is ON, holding the POWER button for 10 seconds to activate the Child Lock fuction. E3 will be displayed that indicate the Child Lock fuction acticate. All function keys are lcoked. When pressing any button, E3 will be displayed that indicate the Child Lock fuction acticate.
Inactivate Child Lock
To inactivate the Child Lock function, holding the POWER button for 10 seconds.
Remote Control
Functions are same as the touch control except Child Lock, Change the temperature unit, Clock Setting and Change between
12H and 24H.
CARE AND MAINTENACE
- Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool whenever you are cleaning the heater.
- Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim.
- The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/output vents is recommended.
- Any other servicing should be performed by an authorized service representative.
WARNING: Make sure the power is turned off before proceeding. Any electrical
repairs or rewiring of this unit should be carried out by a licensed
electrician in accordance with national and local codes.
If repairing or replacing and electrical component or wiring, the original
wire routing, color coding and securing locations must be followed.
WARNING: Electrical outlet wiring must comply with local building codes and
other applicable regulations to reduce the risk of fire, electrical shock and
injury to persons.
CARE AND MAINTENACE
Note: When the heater is not in use, the heater should be stored in a dry location, away from possible damage. The power cord should be stored properly to avoid contact with hot or sharp objects.
Replacing the Remote Control Battery|
When the remote control (E) stops operating or its range seems reduced, it is
time to replace the batteries.
Note: The batteries should be removed if the product is to be left unused
for a long time.
- The battery compartment is located on the back of the remote control (E).
- Remove battery cover from the back of remote control (E).
- Insert 2pcs AAA batteries, ensuring the polarities of the battery match the inside of the battery
- Re-insert the battery
Note:
Do not mix old and new batteries.
Do not mix alkaline, standard (carbonzinc), or rechargeable (nicad, nimh, etc)
batteries.
Non-rechargeable batteries are not to be recharged. Exhausted batteries are to
be removed from the product.
Disposal of Used Battery
A battery may contain hazardous substances that could be endangering to environment and human health.
- This symbol marked on the battery and/or packaging indicates that used battery shall not be treated as municipal waste. Instead it shall be left at the appropriate collection point for
- By ensuring the used battery is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources.
For more information about collection and recycling of used batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased this item.
TROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE
PROBLEM| POSSIBLE CAUSE| SOLUTION
1. No power, logs do not glow.| 1. The unit does not have power.| 1a, Check
that unit is plugged into a standard 120 volt outlet. Then make sure power is
set at “ON” position.
2. E1 displayed on control panel.| 2. The overheat protection device has
been engaged.| 2. Unplug unit, wait 5-10 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the problem persists,
call customer service.
3. E2 displayed on control panel.| 3. The ambient temperature sensor is
broken or not working correctly.| 3. Unplug unit, wait 5-10 minutes, then the
sensor will reset itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
4. E3 displayed on control panel.| 4. Child lock function activate.| 4. To
inactivate the Child Lock function, holding the POWER button for 10 seconds.
5. Fan motor continues to blow after unit is powered off.| 5. Normal
operation.| 5. This is a standard feature; the blower runs for an additional
20 seconds to ensure heat will not be trapped inside the unit.
6. Power cord gets warm to the touch.| 6. Normal
operation.
| 6. This is normal for a heater appliance as it requires more current to
operate. Check the connections of the appliance cord and the outlet. Make sure
the plug fits tightly into the outlet. During use, check the plug and outlet
frequently to determine if it is HOT; if so, discontinue use of the appliance
and consult with a qualified electrician to check or change the overheating
outlet(s).
15
1 YEAR LIMITED WARRANTY
Soupro Limited Inc. (hereinafter referred to collectively as “the Company”) warrants that your new KOMODO Electric Fireplace is free from manufacturing and materials defects for a period of one (1) year from date of purchase. Subject to the following conditions and limitations:
- The electric fireplace must be installed and operated at all times in accordance with the installation and operating instructions furnished with the product. Any unauthorized repair, alteration, willful abuse, accident, or misuse of the product shall nullify this warranty.
- This warranty is non-transferable, and is made to the original owner, provided that the purchase was made through an authorized supplier of the Company.
- The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship — provided that such part(s) have been subjected to normal conditions of use and service —after said defect is confirmed by the Company’s inspection. All replacement parts or products will be new, remanufactured, or refurbished.
- The Company may, at its discretion, require that any defective part(s) be returned in exchange for the replacement part(s).
- The Company may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s).
- This warranty does not cover the LED light bar included with the electric fireplace.
- Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor shall the Company assume responsibility for the same.
- The owner/user assumes all other risks — if any — including but not limited to the risk of any direct, indirect or consequential loss or damage arising out of the use, or inability to use the product, except as provided by law.
- All other warranties — express or implied — with respect to the unit, its components and accessories, or any obligations/liabilities on the part of the Company are hereby expressly excluded.
- The Company neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities with respect to the sale of the unit.
- The warranties as outlined within this document do not apply to non-accessories used in conjunction with the installation of this product. 12. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void if:
(a) The fireplace is subjected to prolonged periods of dampness or condensation.
(b) Any unauthorized alteration, willful abuse, accident, or misuse of the product.
(c) You do not have the original purchase receipt.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>