MELODYSUSIE P Series Atena Cordless Nail Drill Instruction Manual

MELODYSUSIE P Series Atena Cordless Nail Drill

Thank you for choosing MelodySusie! Please read this user guide carefully and keep it in an accessible location so you may refer to it later.

IMPORTANT SAFEGUARDS

• READ ALL INSTRUCTIONS BEFORE USING.
• To reduce the risk of burns, electrocution, fire or al A injury to persons.
• Please be sure to read the safety instruction as follow to avoid potential hazards that could result in personal injuries or damage to the device.
  NOTE: If the use cable connects to the adapter, it is recommended to use an adapter of 5V/2A. Please do not exceed 5V/2A, or the drill will burn out.

Check before Using

1. Check the power supply cord before the first time use and during the life of the device. Do not use the device if it has a damaged cord or plug, or if it is not working properly.
2. Do not plug the device into a voltage system that is not specified on the device or charger. Use with improper voltage will damage the device and VOID warranty.
3. Use the original charger only.

Note for Battery

1. The Battery needs to be charged fully before first use to ensure optimal performance.
2. Do not overcharge the device or use it when it is charging.Charge the device in well-ventilated condition with 0’C-40’C.
3. Do not charge the device close to flammable or explosive materials. When charging the device, please do not cover it with clothes or other things.
4. If the device is not used for long periods of time, you should charge and discharge once every three months. In normal conditions, the battery performance will decline over several years.

Note for Using

1. To prevent electric leakage and shock or fire, do not draw out the connecting wires during use or touch the plug with the wet hand. Turn the power off after use.
2. Do not use the crooked or damaged nail drill bit or replace the bit when power is on.
3. Do not adjust the speed abruptly, stop use once the unusual movement and noise happens.
4. Misuse, dropping or excessive force may cause device damage.
5. Minor should not use this device without parental consent and supervision.

Maintenance Work

1. Do not disassemble the device. Doing so could be dangerous and constitutes voiding warranty conditions.
2. Do not keep the device in a metal box, car, or other places at high temperature(more than 50°G). Keep the handpiece dry and away from oil and grease.
3. Do not store the device in a hot or humid environment. Store it in a cool and dry place.
4. Keep the electrical cord away from heated surfaces.
5. Do not dispose of the device in heat or fire.
6. Do not clean the device with harmful chemicals or detergents.

Note for Injury

1. Having manicures done frequently can cause injuries to the nails as well.
2. If you need to remove the gel polish of natural nails, try to use the nail polish remover pads to avoid damage to the nail bed with improper operation.
3. Do not use the device if you have an open wound on your nail or hand.
4. If you have any skin diseases, heat-sensitive, allergic reactions, onychomycosis, or any other disorder, you should consult your doctor and medical professionals before using the device.

Six Drill Bits

How to use

• Step 1: Choose one nail drill bit, release the hand piece, insert the drill bit into the handpiece and lock it in place.
• Step 2: Press the ON/OFF button for 2 seconds to turn on or off the device.
• Step 3: Press the Speed control to accelerate or decelerate the rotation speed.
• Step 4: Change the rotation direction of the grinding drill bit on the F/R button if needed.

How to Replace Drill Bit?
Please make sure that the desired bit is suitable for the collet.
Do not move central barrel during operation.

1. Turn central barrel clockwise until hearing a “click” sound to release drill bit. Taking out the blank bar. Put the desired bit into the hand piece.
2. Turn central barrel counterclockwise until hearing a “”click”” sound to lock drill bit in place.
3. Be sure to confirm the rotation of the bit and col let. Please take care of your fingers not to be hurt by bit edge.

Charging

1. Take out the cord and connect it with the DC socket.
2. The indicator light of the hand piece shows red and flashes, which means that the drill needs to be charged.
3. The indicator light of the hand piece shows green or blue when the drill is fully charged.

Problem and Terms of Settlement

Specifications

• Input voltage range: 5V/2A
• E-mail: service@melodysusie.com
• E-mail: service.uk@melodysusie.com
• Website: www.melodysusie.com

Warranty and Customer Service

MelodySusie offers a 6 months limited warranty on quality related issues. Please apply for your extra 6 months warranty extension and download the instruction manual in other languages by registering on www.melodysusie.com if needed.

https://www.melodysusie.com
US Service: service@melodysusie.com
UK Service: service.uk@melodysusie.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>