EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point User Guide

June 3, 2024
EnGenius

EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point
User Guide

Introduction

This Quick Start Guide is designed to guide you through the installation of the Fit 2×2 access point, model EWS850-FIT, including hardware mounting and configuration.
Model: EWS850-FIT

  • Wi-Fi 6 technology for high-performance Wi-Fi in high-density, multi-device environments.
  • Two spatial streams support up to 1,200 Mbps (5GHz) & 574 Mbps (2.4GHz).
  • Multiple applications for cloud and on premises solutions.

Package Contents

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
1

System Requirements

Web Browser

  • Google Chrome (57.0.2987.110 and later)
  • Microsoft Edge (80.0.361.103 and later)
  • Mozilla Firefox (52.0 and later)

Hardware Overview

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
2

Reset Button:
Reset to default: Press and hold the reset button on the PoE adaptor for over 60 seconds, and the LED (PWR) will start Fast Flashing (0.2 sec). Then, the device will be reset to factory default settings.
LEDs

STATUS                                                               LED COLOR                                                          LED BEHAVIOR

Connecting to the management (Fixtures/Fit Controller)| PWR (Orange)| Flashing (0.5 Sec.)
Management Connected (Fixtures/Fit Controller/Standalone)| PWR (Orange)| Solid On
LAN Connected| LAN (1G)| LAN (2.5G)| Solid On
LAN Transmitting|  | Flashing
LAN (1G)| LAN (2.5G)
2.4GHz Radio On| 2.4GHz (Green)| Solid On
2.4GHz Transmitting| 2.4GHz (Green)| Flashing
5GHz Radio On| 5GHz (Green)| Solid On
5GHz Transmitting| 5GHz (Green)| Flashing
Firmware Upgrading| PWR| LAN| 2.4GHz| 5GHz| Flashing (0.5 Sec.)
Reset to Default| PWR (Orange)| Fast Flashing
AP Location Mode| PWR| LAN| 2.4GHz| 5GHz| Flashing (1.5 Sec. on ->0.5 Sec. off)

Hardware Mounting

The access point can be mounted on the Wall and Pole, and please perform the steps for the appropriate installation.
Wall Mount

  1. Determine where the Access Point will be placed and mark the location on the surface for the two mounting holes. Use the appropriate drill bit to drill two 8.1mm
    diagram and 26mm-deep holes on the marks.

  2. Screw the Anchors into the holes until they are flush with the wall.

  3. Fasten the Mounting Bracket with the included Screws into the Anchors.
    EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
4

  4. Hang the Access Point against the wall on the Mounting Bracket.
    EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
5

  5. Secure the Access Point on the Mounting Bracket with the secure lock on the side.

Pole Mount

  1. Thread the open end of the Pole Mounting Strap through the two tabs on the Mounting Bracket.
  2. Lock and tighten the Pole Mounting Strap to secure the Mounting Bracket onto the pole.EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point - 7
  3. Hang the Access Point onto the Mounting Bracket.
  4. Secure the Access Point on the Mounting Bracket with the secure lock on the side.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
8

Powering Ingenious Fit AP

Ingenious Fit AP devices can be powered by any of the following:

  • Ingenious Fit Poe switches or 802.3af/ 802.3at Poe+ compliant switches
  • Ingenious Poe Injector (EPA5006GR)

Caution: Do not use both power sources at the same time. Connecting to a PoE Switch
Connect the Ethernet cable from the Ingenious Fit AP directly to the Poe port of the PoE switch.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
9

Powering with a PoE Injector
(A) Connect one end of the Ethernet cable into the LAN (PoE) port of EnGenius FIT AP and the other end to the PoE port on the PoE Adapter.
(B) Connect the power cord with the PoE Adapter and plug the other end into an electrical outlet.
(C) Connect the second Ethernet cable into the LAN port of the PoE Adapter and the other end to the Ethernet port to the network.
Note: Please make sure to use Cat6 RJ45 Ethernet cables.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
10

Management Plane

Ingenious Fit provides flexible options to manage your devices based on your network planning and deployment.
Option A: Cloud Management
Option B: On-Premises Management
Option C: Standalone Configuration

Cloud Management

Manage and monitor the Access Point through the FitXpress Platform with a mobile app or through the web portal.
FitXpress App (iOS/ Android)
Download the Fixtures mobile app App Store click here
Download the Fixtures mobile app Google Play click here

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point - QR
CODEhttps://qr.engenius.ai/app/fitcloud

On-Premises Management

If you want to manage the device in on-premises mode, you need an onsite management station running the Fit Controller connected to the same Layer 2 network.
Fit Controller
Fit Controller is a custom-built appliance with optimized network management software installed to ease onsite deployment without manual server configurations.

Standalone Configuration

Using your computer, you can connect to the same network (subnet) as the Access Point and use the web browser to access the device’s local web GUI page for configurations whenever the device is set to Standalone mode.

Option A: Cloud Management with Fixtures

Step 1: Connecting Ethernet
Connect the Ethernet cable from the Ingenious Fit AP directly to the DHCP- enabled network and make sure the AP can reach the Internet.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
11

Step 2: Register Device
You can register the access point with the Fixtures app.

  1. Open the Fixtures mobile app and create an account.

  2. Login and go to the Devices section. Click the Add (+) button.

  3. Scan the QR code on the back of the device via the app.
    EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
12

  4. If the camera successfully scans the QR code, the app will display the device information. You can tap “Register” to complete the registration.
    EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
13

Step 3: Connect to FitXpress
Once the device is powered on and ready to connect to the Internet, the PWR LED will stay Solid On, which means the device is now connected to the Fixtures platform. It will automatically download the default configuration settings from Fixtures for automated provisioning.
When the Access Point is connected to the Fixtures Platform for the first time, it will automatically check the latest firmware version available. If a firmware upgrade is required, it might take 8~10 minutes to complete the process. All LED indicators will be Flashing (0.5 sec) till the process is finished.
Step 4: Manage with the FitXpress
Log in to the Fixtures app to configure detailed settings and monitor your devices.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
14

Option B: On-premises Management with Fit Controller

Step 1: Connecting Ethernet
Connect the Ethernet cable from the Ingenious Fit AP directly to the DHCP- enabled network, which is the same Layer-2 network as Fit Controller.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
15

Step 2: Log in to the FitController
Launch your web browser to access the login page of Fit Controller and create an account. Enter the email address and password that you created and click Sign In.
The Fit Controller default IP address in DHCP client mode will get an IP address (e.g. X.X.X.X:8080) from the DHCP server. If Fit Controller cannot get an IP address from the DHCP server, the default IP address will be 192.168.1.250:8080.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
16

Step 3: Register Device and Assign to Network

  1. Go to the system > Inventory page and click “Register Device (+)”.
  2. Fit Controller will list all Ingenious Fit devices discovered from the same L2 network in the Pending Approval section. Select the device and Click “Register” to add to inventory. You can also tap “Manually” tab and register Fit device by entering Serial Number.
  3. From the Inventory page, Select the newly added device and click “Assign to Network” to add the device to your personalized network.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
17

Step 4: Pairing the Device

  1. Go to access point or switch list.
  2. Select the newly added device and click “Pairing” to allow the access point to build an encrypted connection between the device and Fit Controller

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
18

Step 5: Manage with FitController
Navigate to the left side menu to configure & manage your network and view network statistics using the Fit Controller management interface.

Option C: Standalone Configuration

Step 1: Access to Local Web

  1. Use your client device (e.g., a laptop, mobile device, or tablet) to find the SSID: “EnMGMTxxxx” and connect to it. 1) EnMGMTxxxx – xxxx is the last four digits of MAC – MAC can be found on the device label on the back of the access point.
  2. Under your web browser, enter the URL: http://EnGenius.local or http://192.168.1.1 to access the device’s user interface.
  3. Use the default login credential (ID/PWD: admin/admin) to log in to the device’s local web page.

Step2: Configure and Manage the Device
After logging into the device’s local web page, navigate to the left side menu to configure and manage the AP accordingly.

EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point -
19

How to Change Management Mode?

Ingenious Fit devices support versatile network management methods, but the device can only be managed under one management mode at a time – either Fixtures, Fit Controller, or Standalone. Therefore, you need to reset the device before changing to a different management mode. Then follow Quick Start Guide instructions for the device onboarding.
Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on distance between devices or traffic and bandwidth load in the network.
Features and specifications subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For United States of America: Copyright
©2022 Ingenious Technologies, Inc. All rights reserved.

Ingenious Technologies
1580 Scenic Ave. Costa Mesa, CA 92626
Email:partners@engeniustech.com 
Website:engeniustech.com
Version:11/2022

Documents / Resources

| EnGenius EWS850-FIT Fit Wi-Fi 6 2×2 Outdoor Wireless Access Point [pdf] User Guide
EWS850-FIT Fit Wi-Fi 6 2 2 Outdoor Wireless Access Point, EWS850-FIT, Fit Wi- Fi 6 2 2 Outdoor Wireless Access Point, Outdoor Wireless Access Point, Wireless Access Point, Access Point
---|---

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals