LARK 84122 Betty LED Wall Sconce Instruction Manual

84122 Betty LED Wall Sconce
Instruction Manual Assembly Instructions
Item No: 84122

84122 Betty LED Wall Sconce

start here

1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.

DRAWING 1 – MOUNTING

1. To begin installation of your fixture it will first be necessary to remove the mounting plate (A) from the backplate (B). This is accomplished by first removing the three screws (C), located at the top and two on the lower side of the backplate. Set screws in a safe place for use later.

2. Next attach mounting plate (A) to junction box (J) with two screws (D), NOT PROVIDED.
   * NOTE:** make sure when installing mounting plate (A) that one of the holes (E) is facing toward the ceiling, before tightening screws (D) – see Drawing 1.

3. Make all necessary electrical connections following instruction sheet IS-18 provided. NOTE: additional anchor holes (X) are provided on the fixture mounting plate. Please use appropriate mounting hardware. (Not Provided)
   SAFETY WARNING: READ WIRING AND GROUNDING INSTRUC-TIONS (LS. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

4. After all connections are made, tuck wires into junction box (J) and slip backplate (B) over mounting tabs (A) and align threaded holes in tab (A) with holes (H) in backplate (B).

5. Thread in screws (C) removed earlier, and tighten to secure fixture to wail.

DRAWING 2 – GLASS INSTALLATION

GLASS INSTALLATION:

1. To install glass, first align notches (N) in glass (1) with tabs (T) inside glass fitter (2) located inside shade (S) – see Drawing 2. CAUTION: When installing the bottom glass make sure glass in engaged correctly to prevent it from falling out.
2. Now slip glass into fitter and twist to lock in place. NOTE: lamp fixture before installing glass.

I.S. 1 8 wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIO NS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS
wiring instructions
Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth, unsnap rked side of the two-conduc for cord) to positive fixture lead (B ) with appropriately sized twist on connector – see Dra wings I or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conduc for cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connec tons

Drawing 1 – Flush Mount

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unsnap rked side of the two-conduc for cord) to positive fixture lead (11) with appropriately sized twist on connector – see Drawings 2 Of 3.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Cover open end of connec tors with silicone sealant to form a watertight seal. B If installing a wall rnoun t fixture, use caulk to seal gaps between the fixture mounting plate (backpla te) and the wall. This will help prevent water from entering the outlet box. If the wal I surface is lap siding, use caulk and a fixture mounting platform specially.
4. Please refer to the grounding Instructions below to complete all electrical connections.

Drawing 2 – Chain Hun g

grounding instructions
Flush Mount Fixtures For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mom ting strap (M) with the ground screw (5) – see Draw in g I.
Note: On straps for screw supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.
Drawing 3 – Post-Mount

Chain Hung Fixtures
Loop fixture ground wire (E) (typically coppe r or green plastic coated) under the head of the ground screw (5) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connec tors – see Draw in g 2.
Post-Moo es
Fixtures Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal-see Drawing 3.

LARK 33000 PIN OAK PARKWAY,
AVON LAKE, OH 44012 LarkLiving.com

References

• Lark Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>