THON Studio Side Rack 10U Instruction Manual

June 12, 2024
THON

Thon Studio Side Rack 10U
Studio RackHON Studio Side Rack 10U

Assembly Instructions

Safety instructions

DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are properly disposed of and are not in the reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from the product. They could swallow the pieces and choke!
Never let children play unattended with the product.
CAUTION!
Risk of injury to the hands

When assembling and screwing the individual parts, pay attention to sharp edges on tools, screws and components.

Scope of delivery

****Before you assemble your rack, make sure the contents of package is complete according to the following list.

  • 2 × side panel, melamine-coated 19 mm furniture board
  • 1 × floor panel, melamine-coated 19 mm furniture board
  • 1 × cover panel, melamine-coated 19 mm furniture board
  • 1 × base, melamine-coated 19 mm furniture board
  • 1 × front panel, melamine-coated 19 mm furniture board
  • 2 × rack rails, 10 U, stepless, equipped with nuts and rubber piping
  • 12 × woodscrew for rack rail
  • 16 × connector housing
  • 16 × connector bolts
  • 8 × wooden dowel
  • 4 × braking furniture caster
  • 16 × raised countersunk screw 4,8×16
  • 1 × assembly instruction
  • 1 × installation template for rack rail

Installation

** Place all components on a suitable mounting surface for mounting. Use a soft padding to prevent damages to the surfaces.
Overview**
The following figure shows an overview of the individual components.HON
Studio Side Rack 10U - Overview

1 Left side panel A Connector bolt
2 Right side panel B Connector housing
3 Base panel C Wooden dowel
4 Cover panel D Woodscrew for rack rail
5 Front panel E Raised countersunk screw 4,8×16
6 Base F Rack rail 10 U
G Furniture caster

Preparing the components
Insert the connector housings, the connecting bolts and the wooden pegs into the holes provided in the components, as shown in the figure below.
Position all connector housings so that the respective connecting bolts can be completely sunk into the holes and the arrow position of the connector housings points towards the hole.
**** After insertion, the connecting bolts sit loosely in the drill holes and only spread apart when the connector housings on the associated component are tightened.HON Studio Side Rack 10U - PreparingHON Studio
Side Rack 10U - Preparing1

1 Left side panel 6 Base
2 Right side panel A Connector bolt
3 Base panel B Connector housing
4 Cover panel C Wooden dowel
5 Front panel

Assembling the components
Place the base panel, the base and the front panel onto the connecting bolts of the left side panel. Tighten the connector housings clockwise to lock the connection with the inserted connecting bolts.HON Studio Side Rack 10U -
Assembling

1 Left side panel 5 Front panel
3 Base panel 6 Base

Place the cover panel onto the connecting bolts of the left side panel. Tighten the connector housings clockwise to lock the connection with the inserted connecting bolts.
Place the right side panel on the pre-assembled unit consisting of the left side panel, base plate, base, front panel and cover plate.
Tighten the connector housings clockwise to lock the connection with the inserted connecting bolts. Check all connections for tight fit.HON Studio
Side Rack 10U - Overview1

2 Right side panel 4 Cover panel

Set the fully assembled unit onto the rack rail front. Screw the four casters into the holes provided in the base panel , each with four raised countersunk screw.
Set up the rack. Screw the rack rails to the inside of the rack, parallel to the front edge, using six wood screws each. We recommend a distance of approx. 1.5 cm from the front edge. A mounting template is included for easy installation.HON Studio Side Rack 10U - Preparing2

D Woodscrew for rack rail F Rack rail 10 U
E Raised countersunk screw 4,8×16 G Furniture caster

Technical specifications

Thon Studio Side Rack 10U WH, white Item number 547450
Thon Studio Side Rack 10U BK, graphite Item number 547455
Thon Studio Side Rack 10U oak Item number 547457
Thon Studio Side Rack 10U beech Item number 547460
Thon Studio Side Rack 10U maple Item number 547461
Rack units 10
Installation depth min. 276 mm
Inclination 45°
Dimensions (W × H × D) 540 mm × 632 mm × 570 mm
Weight approx. 12.6 kg

Protecting the environment

Disposal of the packaging material

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.

Notes

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach Germany
Telephone: +49 (0) 9546 9223-0
Internet: www.thomann.de
21.07.2022, ID: 547450, 547455, 547457, 547460, 547461

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals