THON 547938 Studio Side Rack XL 10U Black Instruction Manual
- June 12, 2024
- THON
Table of Contents
Thon Studio Side Rack XL 10U
Studio Rack
Assembly Instructions
Safety instructions
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are properly disposed of and are not
in the reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like)
from the product. They could swallow the pieces and choke!
Never let children play unattended with the product.
CAUTION!
Risk of injury to the hands
When assembling and screwing the individual parts, pay attention to sharp
edges on tools, screws and components.
Scope of delivery
Before you assemble your rack, make sure the contents of package is complete according to the following list.
- 2 × side panel, melamine-coated 19 mm furniture board
- 1 × floor panel, melamine-coated 19 mm furniture board
- 1 × cover panel, melamine-coated 19 mm furniture board
- 1 × front panel, melamine-coated 19 mm furniture board
- 2 × rack rails, 3 U, stepless, equipped with nuts and rubber piping
- 2 × rack rails, 10 U, stepless, equipped with nuts and rubber piping
- 2 × rack rails, 13 U, stepless, equipped with nuts and rubber piping
- 32 × woodscrew for rack rail
- 16 × connector housing
- 16 × connector bolts
- 8 × wooden dowel
- 4 × braking furniture caster
- 16 × raised countersunk screw 4,8×16
- 1 × assembly instruction
- 1 × installation template for rack rail
Installation
Place all components on a suitable mounting surface for mounting. Use a soft
padding to prevent damages to the surfaces.
Overview
The following figure shows an overview of the individual components.
| 1 | Left side panel | C | Wooden dowel |
|---|---|---|---|
| 2 | Right side panel | D | Woodscrew for rack rail |
| 3 | Base panel | E | Raised countersunk screw 4,8×16 |
| 4 | Cover panel | F | Furniture caster |
| S | Front panel | G | Rack rail 3 U |
| A | Connector bolt | H | Rack rail 10 U |
| B | Connector housing | I | Rack rail 13 U |
Preparing the components
Insert the connector housings, the connecting bolts and the wooden pegs into
the holes provided in the components, as shown in the figure below.
Position all connector housings so that the respective connecting bolts can be
completely sunk into the holes and the arrow posi‐ tion of the connector
housings points towards the hole.
After insertion, the connecting bolts sit loosely in the drill holes and only
spread apart when the connector housings on the associated component are
tightened.
| 1 | Left side panel | 5 | Front panel |
|---|---|---|---|
| 2 | Right side panel | A | Connector bolt |
| 3 | Base panel | B | Connector housing |
| 4 | Cover panel | C | Wooden dowel |
Assembling the components
Place the base panel, the cover plate and the front panel onto the connecting
bolts of the left side panel. Tighten the connector housings clockwise to lock
the connection with the inserted connecting bolts.
Place the right side panel onto the pre-assembled unit consisting of the base
panel, cover panel and front panel. Tighten the con‐ nector housings clockwise
to lock the connection with the inserted connecting bolts. Check all
connections for tight fit.
| 1 | Left side panel | 4 | Cover panel |
|---|---|---|---|
| 2 | Right side panel | 5 | Front panel |
| 3 | Base panel |
Set the fully assembled unit onto the rack rail front. Screw the four casters into the holes provided in the base panel , each with four raised countersunk screw.
| E | Raised countersunk screw 4,8×16 | F | Furniture caster |
|---|
Set up the rack. Use the wood screws provided to screw the rack rails to the
inside of the rack parallel to the front and rear edges. We recommend a
distance of approx. 1.5 cm from the front edge. A mounting template is
included for easy installation.
| D | Woodscrew for rack rail | H | Rack rail 10 U |
|---|---|---|---|
| G | Rack rail 3 U | I | Rack rail 13 U |
Technical specifications
| Thon Studio Side Rack XL 10U black, graphite | Item number 547938 |
|---|---|
| Thon Studio Side Rack XL 10U white | Item number 547939 |
| Thon Studio Side Rack XL 10U oak | Item number 547941 |
| Thon Studio Side Rack XL 10U maple | Item number 547944 |
| Thon Studio Side Rack XL 10U beech | Item number 547946 |
| Rack units | 3, 10, 13 |
| Installation depth | min. 340 mm |
| Inclination | 45° |
| Dimensions (W × H × D) | 540 mm × 700 mm × 620 mm |
| Weight | approx. 15.9 kg |
Protecting the environment
Disposal of the packaging material For the transport and protective
packaging, environmentally friendly materials have been chosen that can be
supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but
make sure that they are collected for recycling. Please follow the notes and
markings on the packaging.
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
Internet: www.thomann.de
29.09.2022, ID: 547938, 547939, 547941, 547944, 547946