BEZGAR HQ051 Remote Control Drone User Manual

BEZGAR HQ051 Remote Control Drone

Product Information

• Product Name: REMOTE CONTROL DRONE
• Model: HQ051
• Manufacturer: SHANTOUSHI CHENGHAIQU XIONGMUWANJUSHANGHANG
• Address: NO.3-2, BLDG 4, NORTH OF THE XINXIN LU, XIMEN, CHENGHUA, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG, CHINA 515800

Product Usage Instructions

1. Ensure the drone is fully charged before use. Connect the included charging cable to the drone and a power source.
2. Place the drone on a flat surface and turn on the power switch located on the drone.
3. Take the remote control and turn it on by pressing the power button.
4. Ensure that the drone and remote control are paired by following the pairing instructions in the user manual.
5. Once paired, use the joystick on the remote control to control the movement of the drone. Push the joystick up to make the drone ascend, and pull it down to make it descend.
6. To make the drone move forward, push the joystick forward. To make it move backward, pull the joystick backward.
7. To rotate the drone, use the left and right controls on the remote control.
8. Make sure to fly the drone in an open area away from obstacles and people. Avoid flying in windy conditions.
9. If the drone starts losing control or the battery is running low, land it immediately to prevent accidents.
10. After use, turn off the power switch on both the drone and remote control.
11. Store the drone in a safe and dry place, away from direct sunlight and extreme temperatures.

REGISTERING YOUR MODEL
In order to serve you better as our customer, please register your product within 15 days of your purchase online at www.bezgar.com–Register your drone.

IMPORTANT INSTRUCTION

1. This product is not a toy but a precision equipment with integrated mechanics and electronics. This product requires expertise in aerodynamics and high-frequency transmitting. This product needs to be correctly assembled and debugged to avoid accidents. The product owner should operate and control it in as safe manner. Please note that we are not liable or responsible for any accidents that may result in injury, damage or loss of property. We urge you to handle with care.
2. This product is suitable for users that have prior operating experience or users no less than the age14.
3. The flying ground suggested is an open space that is legally viable for remote drone control.
4. To avoid the drone losing control, we recommend indoor use only!
5. If you encounter any problems while operating or repairing this product, kindly contact us. We will provide you with the technical support and after-sale service.

BATTERY REPAIR & MAINTENANCE

1. DO NOT mix new and old batteries.
2. DO NOT mix alkaline, standard(carb con-zinc, or rechargeable nickel-cadmium) batteries.
3. Battery should be put in the dry or well ventilated area with a room temperature of about 18-25°C.
4. In order to prolong the battery life, please avoid repeatedly charging or excessive discharging.
5. If the battery needs to be stored away for while, please charge the battery first. The battery needs to be charged to at least 50-60% of its capacity.
6. If you do not use it for more than a month, it is highly recommended that you need to check the battery voltage every month to make sure the voltage is no less than 3V. Otherwise please do not follow step NO.(5).

GET TO KNOW YOUR TRANSMITTER

HOW TO CHARGE DRONE BATTERY

1. Pull the battery out of the drone.

2. Take out the USB char insert into the battery
   (Make sure the ports are connected correctly)

3. Connect the USB charger to the computer USB port, then connect the charging socket to the ithium battery. While charging. the LED wil light up; when fully charged, the LED will turn off

4. Reconnect the battery to the drone.
   Charging time: about 70-90 minutes. When drone’s power getting low, the indicator light will flash rapidly.

CAUTIONS WHEN CHARGING

1. Charging by using power socket can cause fire! Please always charge the battery by using the USB port from your computer and not a telephone or tablet wall charger.

2. When charging, please put this product in a dry or well ventilated area.
   Keep it away from any heat sources or explosive products.

3. Before charging, remove the batteries from the drone. Charging process should be supervised by an adult to prevent an accident.

4. After flying, please do not charge the battery if the surface temperature is still not cool. Otherwise it may cause the battery to swell, this could be a fire hazard.

5. Please make sure that you use the original USB charging cable provided. If the battery has been used for a long time, or appears to be swollen, please replace them.

6. If you do not play with the drone for a long time, please remove the battery.

READY TO FLY YOUR DRONE

STEP 1
Slide open the battery cover on the drone. Insert the battery, connect the battery cable into the drone plug point. Make sure it fits correctly, then slide the battery cover to close. Turn the switch on the drone to ON, and place it down onto a flat surface making sure the drone is facing away from you.

STEP 2
Make sure the drone is switched on, turn on the controller power switch, and you will hear beeping sounds. Then push the left stick to the top and pull it down to bottom (as photo 1 & 2), the drone will automatically connect with the controller. All the LEDS will flash and stay on. Now it is ready to fly. Click the one key takeoff button (as photo 3) to start your flight!

FLIGHT CONTROL

SPEED CONTROL

The first time you turn on the drone, the initial speed is set to 40%. You will hear one beep. When you press the speed button, you will hear two beeps which will increase the speed level to 60%. Pressing the speed button again you will hear three beeps and this will increase the level to 100%. Pressing again will bring you back to 40% speed and you will hear one beep. Always learn to fly at 40% speed, and then you can increase it as you get better at flying.

FLIGHT ADJUSTMENT SECTION

When you lift your drone into the air, without the use of any control levers, it should hover in one spot. If it doesn’t, you can follow the instructions below to bring your drone back to a perfect hover.

HOW TO LAND YOUR DRONE

Option 1:
After playing, control the drone to the ground and keep the throttle at the lowest position for 3-4 seconds or until the motor stops working. Finally switch off the transmitter and drone.
Option 2:
For a fast turn off, press the one key landing button, the drone will slowly land on the ground and motor will shut down.

RESETTING THE DRONE

Pull the left stick to lower left quarter, and pull the right stick to lower right quarter (as photo), you will hear beeping sound and the LED lights begin to flash and stay on the gyro will auto reset and keep better balance. Please notice that the drone should be put on the flat surface.

HOW TO DO A 360 FLIP

1. Make sure the drone is flying at least 1.5 meters above the floor, or 1.5 meters below i ceiling.
2. Press the flip button on the controller, the controller will make “beep” sound, then flick the right hand lever in any direction, the drone will flip in that direction.
3. You may need to push up on the Up/Down lever after the flip, if your battery is low on power to keep the drone high in the air after the flip.

HEADLESS MODE

When drone successfully enter the headless mode, the indicator light will flicker repeatedly.

When signal connection is finished as picture below (the directions of the drone and player are the same), press the headless mode button for 3 seconds to enter headless mode, no matter what direction the head of the drone towards, it wil fly forward when you push the control stick forward, it will fly backward when you pull the control stick backward.

Please notice that:
Once signal connection is finished, the direction of the drone (but not the player) will be marked. In this case (same direction), enter headless mode. Push the control stick forward, it will fly towards the direction which is marked front when signal connection. Push the control stick back / left / right to fly back / left / right.

When signal connection is finished as picture below (the directions of the drone and player are opposite), press the headless mode button for 3 seconds to enter headless mode, no matter what direction the head of the drone towards, it will fly close to you, when you push the control stick forward, it will fly away from you, when you pull the control stick backward.

Please notice that:
Once signal connection is finished, the direction of the drone (but not the player) will be marked. In this case (opposite direction) enter headless mode, push the control stick forward, it will fly towards the direction which is marked front when signal connection. (Now the front is the opposite direction of the player) Push the control stick back/ left / right to fly forward / right / left. (Now the directions are also opposite to the plays)

ONE KEY RETURN

This function helps you to fly it back in case of any lost. When pressing this button for 3 seconds, the drone will automatically fly backward. Quit the mode when pushing the right control stick towards any direction.

Situation 1
Please notice that:
In this case (same direction), press the auto-back fly button for 3 seconds, it will fly dose to you automatically.

This function helps you to fly it back in case of any lost. When pressing this button for 3 seconds, the drone will automatically fly backward. Quit the mode when pushing the right control stic towards any direction.

Sítuation 2.
Please notice that:
In this case (opposite direction), press the auto-back fly button for 3 seconds, it will fly away from you automatically.

BLADE REPLACEMENT INSTRUCTION

The drone comes with replacement blades, if the originals are broken or badly damaged. It is extremely important to use the correct blade (A or B) for replacement. The marking can be found on the blades. Using the incorrect blade will make it impossible to control the drone.
(Assembly of the blades: Clip the small cap of the blade, and then aim at the shaft of the motor and press it. It may require a little force. Please be careful so you don’t break it.)

PRECAUTIONS
Adult’s Supervision Required
This product needs to be used safe environment in order to avoid electric shock.
Users aged 14 or below are better to play it under adults accompanied.

CUSTOMER SUPPORT

If you have any questions about your model or its operation, call BEZGAR Customer Support at +1 833-325-1118 or E-mail: SUPPORT@BEZGAR.COM.

Produce name: REMOTE CONTROL DRONE
Model: HQ051
Manufacturer: SHANTOUSHI CHENGHAIQU XIONGMUWANJUSHANGHANG
Address: NO.3-2.BLDG 4,NORTH OF THE XINXIN LUXIMEN, CHENGHUA, CHENGHAI
DISTRICT,SHANTOU CITY,GUANGDONG,CHINA 515800

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>